Epson Projector Emp S5 User Manual

							61
Connecting to External EquipmentConnecting to an External Monitor
Computer images being input to the Computer1 input port or the 
Computer Input port can be displayed on an external monitor and the 
screen at the same time when connected to the projector. This means that 
you can check projected images on an external monitor when giving 
presentations even if you cannot see the screen.
Connect to an external monitor using the cable supplied with the monitor.
Connecting to External Speakers (EMP-83/822 Only)
You can connect speakers with built-in amplifiers to the projectors Audio 
Out port to enjoy a fuller quality of sound.
Connect with a commercially available audio cable (pin plug W 3.5 mm 
stereo mini plug and so on). Use an audio cable compatible with the 
connector on the external speakers.
q
 Component video signals and images connected to the 
Computer2 port, Video port, and S-Video port cannot be 
output to an external monitor.
 The setting gauge for Keystone, the configuration and 
help screen, and so on are not output to an external 
monitor.
Cable supplied 
with monitor
To Monitor Out port Monitor port
q
When an audio cable plug is inserted in the Audio Out port, 
the audio changes to the external destination, and audio is 
no longer emitted from the projectors built-in speaker.
To external speakers
To Audio Out port
Audio cable
(commercially available) 
						

							62
Connecting a LAN Cable (EMP-83/822 Only)Connect with a commercially available 100baseTX or 10baseT type 
LAN cable.
AttentionTo prevent malfunctions, use a category 5 shielded LAN cable.To LAN port
To LAN port
LAN cable
(commercially available) 
						

							63
Connecting a USB Cable (EMP-X5/S5 Only)Connect the USB
g port of a computer and the USBport (TypeB) on 
the rear of the projector with a commercially available USB cable.
USB cableTo USB port 
(Type B) To USB port 
						

							64
Optional Accessories and ConsumablesPrepare the following options and consumables. Purchase depending 
on usage. The following list of optional accessories is current as of 
March, 2007. Details of accessories are subject to change without 
notice and availability may vary depending on the country of purchase. fOptional accessories
* A special method of installation is required to suspend the projector from a 
ceiling. Contact your dealer or the nearest address provided in the 
International Warranty Terms if you want to use this installation method. 
sInquiries
fConsumables
Soft carrying case ELPKS16B
Use this case if you need to travel with the projector.60 portable screen ELPSC07
80 portable screen ELPSC08
100 screen ELPSC10
Portable roll-type screens (Aspect ratio
g 4:3)
50 portable screen ELPSC06
A compact screen that can be carried easily. (Aspect ratio 4:3)HD-15 cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
This is the same as the computer cable supplied with the projector. HD-15 cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
HD-15 PC cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Use one of these longer cables if the computer cable bundled with the product is too 
short. Component video cable ELPKC19
(3 m - for mini D-Sub 15-pin/RCA male^3)
Use to connect a component video
g source 
Ceiling plate
* ELPFC03 
Pipe 370 (370 mm silver)
* ELPFP04
Pipe 570 (570 mm silver)* ELPFP05
Pipe 770 (770 mm silver)* ELPFP06
Ceiling mount (For use with the ceiling plate)
* ELPMB18
Use when installing the projector on a ceiling. 
Lamp unit (For EMP-X5/S5) ELPLP41
Lamp unit (For EMP-83/822) ELPLP42
Use as a replacement for used lamps. Air filter (by 2) ELPAF13
Use as a replacement for used air filters.  
						

							65
GlossaryThis section briefly explains terms that are used with the projector and difficult terms that are not explained in the text of this guide. For details, 
refer to other commercially available publications.
Aspect ratio
The ratio between an images length and its height. HDTV images have an aspect ratio of 16:9 and appear elongated. The aspect ratio for 
standard images is 4:3. 
Component Video
A video signal which has the luminance component and color component separated to provide better image quality. 
Refers to images that consist of three independent signals: Y (luminance signal), Pb and Pr (color difference signals). 
Composite video
Video signals that have the video brightness signals and color signals mixed together. The type of signals commonly used by household 
video equipment (NTSC, PAL, and SECAM formats). The carrier signal Y (luminance signal) and chroma (color) signal that are 
contained in the color bar are overlapped to form a single signal.
Contrast
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more 
clearly, or to make them appear softer. Adjusting this particular property of an image is called contrast adjustment. 
DHCP
An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP address
g to equipment connected to 
a network.
Dolby Digital
A sound format developed by Dolby Laboratories. Normal stereo is a 2-channel format that uses two speakers. Dolby Digital is a 6-
channel (5.1-channel) system which adds to this a center speaker, two rear speakers, and a sub-woofer. 
Gateway address
This is a server (router) for communicating across a network (subnet) divided according to subnet masks
g.
HDTV
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions. 
 Vertical resolution of 720p or 1080i or greater (p = progressive
g, i = interlace
g)
 Screen aspect ratio
g of 16:9 
 Dolby Digital
g audio reception and playback (or output) 
Interlace
A method of image scanning whereby the image data is divided into fine horizontal lines that are displayed in sequence starting from left 
to right and then from top to bottom. The even-numbered lines and odd-numbered lines are displayed alternately. 
IP address
A number to identify a computer connected to a network.
Progressive
A method of image scanning whereby the image data from a single image is scanned sequentially from top to bottom to create a single 
image. 
Refresh rate
The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image 
must be scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the 
Refresh rate and is expressed in hertz (Hz). 
SDTV
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for 
HDTV
g High-Definition Television. 
SNMP
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers 
and computers connected to a TCP/IP network.
SNMP Trap IP address
This is the IP address
g for the destination computer used for error notification in S NMP 
						

							Glossary
66
Squeeze mode
In this mode, wide-screen images in 16:9 mode are compressed in the horizontal direction so that they are stored on the recording 
medium as 4:3 images. 
When these images are played back by the projector in squeeze mode, they are restored to their original 16:9 format. 
sRGB
An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled 
easily by computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the 
connected signal source to sRGB.
Subnet mask
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
SVGA
A type of video signal with a resolution of 800 (horizontal) ^ 600 (vertical) dots that is used by IBM PC/AT-compatible computers. 
S-Video
A video signal which has the luminance component and color component separated to provide better image quality. 
Refers to images that consist of two independent signals: Y (luminance signal) and C (color signal). 
SXGA
A type of video signal with a resolution of 1280 (horizontal) ^ 1024 (vertical) dots that is used by IBM PC/AT-compatible computers. 
Synchronization
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting 
images are not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in 
the signal) is called Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur. 
Tracking
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting 
images are not of a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called 
Tracking. If tracking is not carried out correctly, wide vertical stripes appear in the signal. 
VGA
A type of video signal with a resolution of 640 (horizontal) ^ 480 (vertical) dots that is used by IBM PC/AT-compatible computers. 
XGA
A type of video signal with a resolution of 1024 (horizontal) ^ 768 (vertical) dots that is used by IBM PC/AT-compatible computers.  
						

							67
ESC/VP21 CommandsCommand List
When the power ON command is transmitted to the projector, the power 
turns on and it enters warm-up mode. When the projectors power has 
turned on, a colon : (3Ah) is returned. 
When a command is input, the projector executes the command and 
returns a :, and then accepts the next command. 
If the command being processed terminates due to a problem, an error 
message is output and a : is returned. * Add a Carriage Return (CR) code (0Dh) to the end of each command and 
transmit.
Cable LayoutsfSerial connection (EMP-83/822 Only)
Item
Command
Power ON/OFF
ON
PWR ON
OFF
PWR OFF
Signal selection
Vid e o
SOURCE 41
S-Video
SOURCE 42
A/V Mute ON/OFF
ON
MUTE ON
OFF
MUTE OFF
A/V Mute selection
Black
MSEL 00
Blue
MSEL 01
Logo
MSEL 02
Item
Command
Computer1 
Port
Computer2 
Port
Signal selection
Computer (Auto)
SOURCE 1F
SOURCE 2F
Computer
SOURCE 11
SOURCE 21
Component Video
SOURCE 14
SOURCE 24
 Connector shape : D-Sub 9-pin (male)
 Projector input connector : RS-232C
At the projector
(PC serial cable)
At the computer
Signal
Function
GND
5
5
GND
GND
Signal wire 
ground
RD
2
3
TD
TD
Transmit data
TD
3
2
RD
RD
Receive data
DTR
4
6
DSR
DSR
Data set ready
DSR
6
4
DTR
DTR
Data terminal 
ready
  
						

							ESC/VP21 Commands
68
Connecting a USB (EMP-X5/S5 Only)
Connector shape: USB (Type B)
USB Connection Setup
To control the projector using ESC/VP21 commands via a USB 
connection, the following preparations must be carried out.A
Download the USB driver (USB-COM Driver) from 
the Epson Web site to your computer.Go to http://www.epson.com and select the support section of your 
local Epson Web site.
B
Install the downloaded USB driver onto your 
computer.Read the instructions displayed on the download screen.
C
Set Extended-Link 21L to On from the 
projectors configuration menu.
 
(Type B)
Procedure 
						

							69
PJLink (EMP-83/822 Only)PJLink Class 1 was established by the JBMIA (Japan Business 
Machine and Information System Industries Association) as a standard 
protocol for controlling network-compatible projectors as part of their 
efforts to standardize projector control protocols.
The projector complies with the PJLink Class 1 standard established 
by the JBMIA.
It complies with all commands except for the following commands 
defined by PJLink Class 1, and agreement was confirmed by the 
PJLink standard adaptability verification.
Refer to the JBMIA (Japan Business Machine and Information System 
Industries Association) Web site for more details on PJLink.
URL http://pjlink.jbmia.or.jp/english/fNon-compatible commands
fInput names defined by PJLink and corresponding 
projector connectorsfManufacturer name displayed for Manufacture name 
information query
EPSON
fModel name displayed for Product name information 
query
EMP-83
EMP-822
Function
PJLink Command
Mute settings
Image muting set
AV M T  1 1
Image muting cancel
AV M T  1 0
Audio muting set
AV M T  2 1
Audio muting cancel
AV M T  2 0
Input Connector
PJLink Command
Computer1 input 
INPT 11
Computer2 input 
INPT 12
Video input
INPT 21
S-Video input 
INPT 22 
						

							70
List of Supported Monitor DisplaysfComputer image
*1 Connection is not possible if the equipment does not have a VGA output port.
*2 EMP-S5 is not supported.
Even when signals other than those mentioned above are input, it is likely that the 
image can be projected.
However, not all functions may be supported. 
fComponent Video
fComposite video/S-video
Signal
 Refresh Rate
g
 (Hz)
Resolution
 (dots)
Number of 
Pixels Used 
Display 
Aspect is 
Resized 
(dots)
VGAEGA
640 ^ 350
1024 ^ 560
VGA
g
60/72/75/85, iMac
*1
640 ^ 480
1024 ^ 768
SVGA
g
56/60/72/75/85, iMac
*1
800 ^ 600
1024 ^ 768
XGA
g
60/70/75/85, iMac
*1
1024 ^ 768
1024 ^ 768
SXGA
g
70/75/85
1152 ^ 864
1024 ^ 768
SXGA
60/75/85
1280 ^ 960
1024 ^ 768
SXGA
60/75/85
1280 ^ 1024
960 ^ 768
UXGA
*2
60
1600 ^ 1200
1024 ^ 768
MAC13
640 ^ 480
1024 ^ 768
MAC16
832 ^ 624
1024 ^ 768
MAC19
1024 ^ 768
1024 ^ 768
MAC19
60
1024 ^ 768
1024 ^ 768
MAC21
1152 ^ 870
1016 ^ 768
SDTV
g 
(480i)
60
720 ^ 480
1024 ^ 768
SDTV (576i)
50
720 ^ 576
1024 ^ 768
SDTV (480p)
60
720 ^ 480
1024 ^ 768
SDTV (576p)
50
720 ^ 576
1024 ^ 768
HDTV
g 
(720p)
50/60
1280 ^ 720
1024 ^ 576
HDTV (1080i)
50/60
1920 ^ 1080
1024 ^ 576
Signal
Refresh Rate
g
 (Hz)
Resolutions (dots)
Aspect Ratio
g 4:3
Aspect Ratio 
16:9
SDTV
g (480i)
60
1024 ^ 768
1024 ^ 576
SDTV (576i)
50
1024 ^ 768
1024 ^ 576
SDTV (480p)
60
1024 ^ 768
1024 ^ 576
SDTV (576p)
50
1024 ^ 768
1024 ^ 576
HDTV
g 
(720p)
16:9
50/60
1024 ^ 768
1024 ^ 576
HDTV (1080i)
16:9
50/60
1024 ^ 768
1024 ^ 576
Signal
Refresh Rate
g
 (Hz)
Resolutions (dots)
Aspect Ratio
g 4:3
Aspect Ratio 
16:9
TV (NTSC)
60
1024 ^ 768
1024 ^ 576
TV
(PAL, 
SECAM)
50
1024 ^ 768
1024 ^ 576