Epson Projector Emp 732 User Manual

							70
Using the Configuration Menu FunctionsUser’s Guide
Select a sub-menu item.
Tilt the [ ] button on the remote control up and down or press 
the [ ] and [ ] buttons on the projectors control panel to 
move to the sub-item to be set, and then press the [Enter] 
button.
The items that are displayed in the Image menu, Signal 
menu and Info menu vary depending on the input source that 
is being projected.
Change the setting.
(1) Tilt the [ ] button on the remote control or press the [ ] 
and [ ] buttons on the projectors control panel to change 
the setting.
 : Current setting value
 : Currently-selected setting item
(2) If you press the [Enter] button when at items with a   
displayed, the setting screen for that item will be 
displayed.
After making the setting, press the [Enter] button to accept 
the setting. The   will change to green.
Tilt the [ ] button on the remote control to the left or right or 
press the [ ] and [ ] buttons on the projectors control panel to 
change the setting.
Press the [Enter] button to accept the setting.
4
5
Example 1Example 2 
						

							71
Using the Configuration Menu FunctionsUser’s Guide
Close the menu.
Press the [Menu] button.
6
TIP
Refer to List of Functions for details on the functions of each menu 
item. 
s
p.56 
						

							TroubleshootingThis chapter describes how to identify problems and what to do if a problem is found.Using the Help ..................................................... 73
Problems Solving................................................ 75
 Reading the Indicators........................................................ 75 Power indicator lights red .......................................................... 75
 Lamp or Temp indicator flashes orange .................................... 76
 Power indicator lights green or orange/flashes 
green or orange .......................................................................... 77 When the Indicators Provide No Help .............................. 78 Problems relating to images ...................................................... 80
 Problems when projection starts ................................................ 86
 Other problems .......................................................................... 87
 Problems Relating to Monitoring and Controlling Projectors 
Using a Network (EMP-745/737 only)...................................... 88 
						

							73
User’s Guide
Using the HelpIf a problem occurs with the projector, the Help function uses on-screen 
displays to assist you in solving the problem. It uses a series of menus in a 
question and answer format.
PROCEDURE
Press the [Help] button.
The help menu will be displayed.Select a menu item.
Tilt the [ ] button on the remote control or press the [ ] and 
[ ] buttons on the projectors control panel to select an item.
Confirm the selection.
Press the [Enter] button to confirm the selection of a menu item.
1
Projector
Remote control
2
Remote controlProjector
3
Remote control Projector 
						

							74
Using the HelpUser’s Guide
Repeat the operations in steps 2 and 3 to proceed 
through the menu to more detailed items.
The help menu is cleared when the [Help] button is pressed.
4
TIP
If the Help function does not provide a solution to the problem, refer 
to Problem Solving 
s
p.75  
						

							75
User’s Guide
Problems SolvingIf you are having a problem with the projector, first check the projectors indicators and refer to Reading the Indicators below.
If the indicators do not show clearly what the problem might be, refer to When the Indicators Provide No Help. sp.78Reading the Indicators
The projector is provided with the following three indicators which indicate the operating status of the projector.
The following tables show what the indicators mean and how to remedy problems that they indicate.
If all indicators are switched off, check that the power cable is connected correctly and that power is being supplied normally.Power indicator lights red
       : lit    : flashing    : off
Status
Cause
Remedy or Status
Internal error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your 
dealer or the nearest address provided in the International Warranty Conditions section of the 
Safety Instructions/World-Wide Warranty Terms 
booklet.
Fan related error/
Sensor error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your 
dealer or the nearest address provided in the International Warranty Conditions section of the 
Safety Instructions/World-Wide Warranty Terms 
booklet.
Lamp indicatorPower indicatorTemp indicator
Abnormal
Red
Red
RedRed
Red 
						

							76
Problems SolvingUser’s Guide
Internal temperature error
(overheating)
The lamp will turn off automatically and projection will stop. Wait for about 5 minutes. After 
about 5 minutes the projector will switch to standby mode, so check the following two points. 
After checking, press the [Power] button to turn the power back on.
 Check that the air filter and air exhaust vent are clear, and that the projector is not positioned 
against a wall. sp.16
 If the air filters are blocked, clean or replace them. sp.99, p.104If this does not solve the problem and the projector continues to overheat or the indicators continue 
to show a problem when the power is turned on, stop using the projector, disconnect the power cable 
from the wall outlet, and contact your dealer or the nearest address provided in the International 
Warranty Conditions section of the Safety Instructions/World-Wide Warranty Terms 
booklet.
Lamp timer failure/
Lamp out
Take out the lamp and check if it is broken. sp.101
If the lamp is not broken, put it back in and then turn the power on. If the lamp still does not turn 
on, replace it with a new lamp.
If this does not solve the problem, stop using the projector and disconnect the power cable from 
the electrical outlet. Then contact your dealer or the nearest address provided in the International 
Warranty Conditions section of the Safety Instructions/World-Wide Warranty Terms 
bookletIf the lamp is broken replace it with a new lamp, or contact your local dealer for further advice.
If replacing the lamp yourself, be careful to avoid pieces of broken glass.
 (Projection cannot be carried out until the lamp is replaced.)Check that the lamp and the lamp cover are securely installed. If the lamp or lamp cover is not 
securely installed, the lamp will not switch on.
Lamp or Temp indicator flashes orange
       : lit    : flashing    : off
Status
Cause
Remedy or Status
High-speed cooling in progress
(This is not an abnormality, but if the temperature rises too high again, projection will stop 
automatically.)
 Check that the air filters and air exhaust vent are clear and that they are not up against a surface 
such as a wall. sp.16
 If the air filters are clogged, clean or replace them. sp.99, p.104       : lit    : flashing    : off
Status
Cause
Remedy or Status
Red
RedRed
Red
War ning
Red
Orange 
						

							77
Problems SolvingUser’s Guide
Lamp replacement notification
Replace the lamp with a new one. sp.101
If you continue to use the lamp after it has passed the replacement period, the possibility that the 
lamp may break will increase. Replace the lamp with a new one as soon as possible. The Power 
indicator status will vary depending on the projector status at the time.
Power indicator lights green or orange/flashes green or orange
     : lit    : flashing    : off
Status
Cause
Remedy or Status
Standby condition
Projection starts again when the [Power] button is pressed.
You can disconnect the power plug from the electrical outlet when the status light is in this 
condition.
Warm-up in progress
Warm-up time is approximately 40 seconds. After warm-up is complete, the indicator stops 
flashing.
Projection in progressCool-down in progress
Please wait.
 The cool-down
g period lasts about 20 seconds.
 The [Power] button will not operate if it is pressed while cool-down is in progress. When the 
cool-down period is finished and the confirmation buzzer has sounded and the indicator changes 
to light orange, repeat the operation.       : lit    : flashing    : off
Status
Cause
Remedy or Status
Orange
Normal
OrangeGreenGreenOrenge
TIP
 If the projector is not operating properly even though the indicators are all showing normal, refer to When the Indicators Provide No Help 
on the following page.
 If an indicator is showing a status which does not appear in the previous tables, contact your dealer or the nearest address provided in the 
International Warranty Conditions section of the Safety Instructions/World-Wide Warranty Terms booklet. 
						

							78
Problems SolvingUser’s GuideWhen the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem.
No images appear sp.80
Projection does not start, the projection area is completely black, the 
projection area is completely blue, etc.Can not switch projection to a video source by pressing the 
[Source Search] button sp.80Projection stops automatically sp.81The message Not Supported. is displayed sp.81The message No Signal. is displayed sp.82Images are fuzzy or out of focus sp.82Interference or distortion appear in images sp.83
Problems such as interference, distortion or black & white checked 
patterns appear.Image is truncated (large) or small sp.84
Only part of the image is displayed.Image colours are not right sp.85
The whole image appears purplish or greenish, images are black & 
white, colours appear dull, etc.
(Computer monitors and LCD screens have different colour 
reproduction performance, so that the colours projected by the 
projector and the colours appearing on the monitor may not 
necessarily match, but this is not a sign of a problem.)Images appear dark sp.86Problems relating to images
Power does not turn on sp.86No sound can be heard or the 
sound is faint sp.87The remote control does not work 
sp.87The projectors control panel does 
not work sp.87The fans do not stop when power 
is turned off (EMP-745/737 only) 
sp.88Problems when projection startsOther problems 
						

							79
Problems SolvingUser’s Guide
Mail notification messages are not 
being sent when a problem occurs 
with the projector sp.88The projector cannot be monitored 
and controlled using the EMP 
Monitor function sp.89An error message is displayed (error message when EMP 
Monitor is running) sp.97
You cannot connect from another computer when images are 
being projected during a network connection sp.89 
EMP NS Connection starts, but a projector is not found 
sp.90
Connection cannot be established in access point mode or 
wired LAN connection mode sp.91
Connection cannot be made in ad hoc mode sp.91
Network Screen images are not displayed, or the display is 
slow sp.92
The PowerPoint slideshow does not work when using the 
Network Screen sp.92
Keynote slideshows cannot be played back with Network 
Screen sp.92
Network Screen cannot be used sp.93
When running Microsoft Office applications using Network 
Screen, the screen does not change as required sp.93
Files do not work correctly with EMP SlideMaker2 sp.93
An error message is displayed sp.94–p.97Problems Relating to Networks and EasyMPFor EMP-745/737 only