Epson Projector Emp 71 User Manual
Here you can view all the pages of manual Epson Projector Emp 71 User Manual. The Epson manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 21
19 Compatible Mode Chart for Connectable Computers If the resolution and frequency of the video signals which are output from the computer do not correspond to any of the values in the table below, those video signals cannot be projected. (In some cases it may be possible to project such signals, but they will not produce clear images.) Check the instruction manual for the computer for details on the resolution and frequency of the video signals. Furthermore, some computers may let you change the...
Page 22
20 Connecting to a Computer Tip: Before connecting, switch off power to the projector and computer. Check that cable and port interfaces match each other. [Projecting Computer Video] You can make presentations on a large screen by projecting computer video from your projector. * If your computer port style is not a mini D-Sub 15-pin interface, use a connection adapter that provides this interface. When connecting to a Macintosh, you may need to use the optional Mac adapter. Tip: When connected do...
Page 23
21 Connecting to an A/V Device [Inputting a Composite Video Signal] [Inputting an S-Video Signal] To Video port (Yellow) To Audio (L) port (White) To Audio (R) port (Red)Video port (Yellow) Audio (R) port (Red) Audio (L) port (White) A/V cable (accessory) To Audio (L) port (White) To Audio (R) port (Red)S-Video port Audio (R) port (Red) Audio (L) port (White) A/V cable (accessory) To S-Video port S-Video cable (sold separately)
Page 24
22 [Inputting a Component Video Image Signal] If using a component video cable Tip: When projecting a component video image, select YCbCr or YPbPr in the Video > Input Signal menu. Select YCbCr if using a DVD player, and select YPbPr if using a HDTV video source. To change the aspect ratio of the projected image between 4:3 and 16:9, select Video > Aspect Ratio menu. To Y port (Green) To Pb or Cb port (Blue) To Pr or Cr port (Red) Audio (L) port (White) Computer/Component Video port DVD player,...
Page 25
23 Providing Sound Through an External Audio Device Connecting the Audio Out port of your projector to a PA system, active speaker system, or other speakers with built-in amplifiers provides powerful, pleasing sound. Use a separately sold audio connection cable (pin ring) connecting to a 0.14inches (3.5mm) stereo mini-jack plug. Tip: When a cable is connected at the Audio Out port the sound output will be switched from the built-in speaker to external sound output. Though the projector outputs...
Page 26
24 Projecting Images Here we begin projecting images from an A/V device. Preparation Warning: Never look into the lens when the projector is switched on. The intense light can damage your vision. Use only the power cord supplied. Use of other cables may cause fire or electric shock. Caution: Do not attempt projection with the lens cover in place. Heat may deform the lens cover. 1.Check that the projector and computer or A/ V device are connected. 2.Remove the lens cover. 3.Attach the power cord...
Page 27
25 Projection When preparations are complete, you are ready for projection. 1.To use the remote control, turn the remote control R/C switch to On. 2.Press the Power button to switch power on. The operation display indicator begins to flash green, and projection begins. After approximately 30 seconds, the operation display indicator changes from flashing green to steady green. Projector Remote control No-Signal is displayed. Depending on your settings, there may be no display. (See page 47) The...
Page 28
26 3.Press the Source button on the projector or the Computer, S-Video or Video button on the remote control to select the video source you wish to project. Each time the Source button on the projector is pressed, the video source cycles between Computer, S-Video and Video. If there is no input at the S-Video port, the Source button switches the video source from Computer to Video. Tip: If projecting a component video picture, change the setting to Computer. 4.Switch on power to the computer or...
Page 29
27 [Settings for laptop and integrated LCD computers (when connected)] When a laptop or integrated LCD computer is connected to the projector, some computers require key commands or settings to change the output destination of a video signal. Keep Fn depressed while pressing F0 to change the setting. For details, consult the instruction manual of the computer you are using. Tip: Some computers may not be able to have images displayed on the computer screen at the same time as they are being projected....
Page 30
28 Adjusting Images This section describes how to obtain the best video performance. See Setup (page 13) for details on setting-up position and projection size. Adjusting the Image Projection Angle Adjust the projection angle of the projector. Adjust the projector to face the screen as directly as possible. 1.Lift the projector to your desired angle of projection. 2.Use your fingers to pull up the foot adjust levers. Front adjustable feet emerge. 3.Release the foot adjust levers. 4.Make fine...