Epson Projector Emp 54 User Manual

							60
Using the Configuration Menu Functions
Using the Configuration Menu Functions
User’s Logo Menu
Sub-menu
Function
Default
Execute
Records a users logo.   p.90
 Press the [Enter] button on the remote control and follow  the procedure appearing on the screen.
 A users logo cannot be recorded if the User’s Logo  Protect function of Password Protect has been set to ON. 
Cancel the Password Protect function before recording a 
users logo.
EPSON logo 
						

							61
Using the Configuration Menu Functions
Using the Configuration Menu Functions
Advanced Menu
Sub-menu
Function
Default
Brightness 
Control
This lets you set the lamp brightness to one of two settings.
Select Low if the images being projected are too bright 
such as when projecting images in a dark room or onto a 
small screen.
When Low is selected, the brightness of the images is 
reduced, the amount of electricity consumed and noise 
produced during projection are reduced and the lamps 
operating life is extended.
High
Startup 
Screen
Sets whether the startup screen is displayed or not.
To change the users logo, you need to record your own users 
logo.
 
 p.90
This cannot be changed from enabled (ON) to disabled 
(OFF) if the User’s Logo Protect function of Password 
Protect has been set to ON. Cancel the Password Protect 
function before changing the setting.
ON 
						

							62
Using the Configuration Menu Functions
Using the Configuration Menu Functions
Color 
Adjustment
Adjusts the absolute Abs. Color Temp.
 and intensity of 
each RGB (red, green, blue) colour for each input source. Abs. Color Temp.: Lets you adjust bright colours within a 
range from reddish tinges to bluish 
tinges. 
If the colour temperature is lower, 
colours appear reddish and color tones 
appear softer. 
If the colour temperature is higher, 
colours appear bluish and colour tones 
appear sharper. Press the [Enter] button 
on the remote control and make the 
adjustment in the colour adjustment sub-
menu that appears. 
RGB : Press the [Enter] button on the remote 
control, select R (Red), G (Green) or 
B (Blue) and make the adjustment in 
the colour adjustment sub-menu that 
appears. 
The settings can be made while viewing 
the projected image on the screen.
(This item cannot be selected if  sRGB has been selected as 
the Color Mode setting in the Image menu.)
Abs. Color 
Temp.: 
Depends on 
connection
Projection
Sets the projection position for the projector. Front : Select when the projector is in front of the 
screen.
Front/Ceiling : Select when the projector is in front of the  screen and suspended from the ceiling.
Rear : Select when the projector is behind the 
screen.
Rear/Ceiling : Select when the projector is behind the  screen and suspended from the ceiling.
Front
Sub-menu
Function
Default 
						

							63
Using the Configuration Menu Functions
Using the Configuration Menu Functions
COM Port
This can be set to either RS-232C or USB, depending on 
the port that is being used for communication with a 
computer.
When this setting is changed, turn off the power 
momentarily, and when the cool-down
 period has finished, 
turn the power back on again. The new setting will be 
applied after the power turns back on.
RS-232C
Language
Sets the language for message displays.  Press the [Enter] button on the remote control and select the  language.
English
(Varies 
depending on 
country of 
purchase)
Reset
Resets all adjustment values for the Advanced menu 
functions except for the Language setting to their default 
settings. Press the [Enter] button on the remote control to reset the  settings.
 Select Reset All to return all settings for menus such as  Image and Audio to  their default settings.    p.65
-
Sub-menu
Function
Default 
						

							64
Using the Configuration Menu Functions
Using the Configuration Menu Functions The Info menu shows the setting details for the current image source.
 The Lamp Hours item appears as 0H for 0–10 hours,  and after that, it appears in units of 1 hour.
Info MenuComputer (Analogue-RGB)/RGB Video/
Component video
 (YCbCr
, YPbPr
)
Video ( Composite video
, S-Video
)
Sub-menu
Function
Default
Lamp 
Hours
Displays the cumulative lamp operating time for both High 
and Low brightness operation.
 When the lamp warning period is reached, the display  characters appear in red.
0H
Lamp-
Hours 
Reset
Initialises the lamp operating time. When this command is 
selected, the cumulative lamp operating time is reset to the 
initial default value.
-
Source
Displays the input source which is currently being projected.
Input 
Signal
Displays the input signal settings. 
(Does not appear when the input source is composite video 
or S-video.)
Vi d e o  
Signal
Shows the video signal format.
(Not displayed for computer, RGB video or component 
video images)
-
Frequency
Displays the horizontal and ve rtical scanning frequencies. 
(Does not appear when the input source is composite video 
or S-video.)
-
SYNC
 
Polarity
Displays the sync polarity. 
(Does not appear when the input source is composite video 
or S-video.)
-
SYNC 
Mode
Displays the sync attributes. 
(Does not appear when the input source is composite video 
or S-video.)
-
Resolution
Displays the input resolution. 
(Does not appear when the input source is composite video 
or S-video.)
-
Refresh Rate
Displays the refresh rate. 
(Does not appear when the input source is composite video 
or S-video.)
- 
						

							65
Using the Configuration Menu Functions
Using the Configuration Menu Functions
Reset All Menu
Sub-menu
Function
Default
Execute
Resets all items in all menus to their default settings. Press the [Enter] button on the remote control to reset the  settings.
 Select Reset in an individual sub-menu such as the  Image or Audio menu to reset only the settings for the 
items in each sub-menu.
 The Input Signal, User’s Logo, Lamp Hours and  Language settings will not retu rn to their default values.
 If Background Color has been set to Logo, the setting  cannot be returned to the default setting if the User’s Logo 
Protect function of Password  Protect has been set to ON.
- 
						

							66
Using the Configuration Menu FunctionsUsing the Configuration Menus
The configuration menus can be operated using the remote control only.PROCEDURE
Press the [Menu] button.
The configuration menu appears.Select a menu item.
Press the [ ] or [ ] button to move to an item to be selected.
Confirm the selection.Press the [Enter] button to confirm the selection of a menu item.The selected sub-menu will then be displayed. 
1
Remote control
2
3 
						

							67
Using the Configuration Menu Functions
Select a sub-menu item.
Press the [ ] and [ ] buttons to select the sub-menu item to be 
set, and then press the [Enter] button.
The items appearing in the Image menu and the Info menu 
will vary depending on the type of input source being projected.
Change the setting.
 Press the [ ], [ ], [ ] and [ ] buttons to change the setting. : Current setting value
 : Currently-selected setting item
 If you press the [Enter] button at items with a   displayed, the  setting screen for that item will be displayed.
After making the setting, press the [Enter] button to accept the 
setting. The   will change to green.Select other menu items in the same way.
Press the [Esc] button once to return to the previous level. 
Alternatively, select Return and then press the [Enter] button.Close the menu.
Press the [Menu] button.
4
567
TIP
Refer to List of Functions for de tails on the functions of each menu 
item. 
 p.51 
						

							TroubleshootingThis chapter describes how to identify problems and what to do if a problem is found.Using the Help ..................................................... 69
Problem Solving.................................................. 71
 Reading the Indicators........................................................ 71 Power Indicator .......................................................................... 71
    (Warning) Indicator ........................................................... 72 When the Indicators Provide No Help ..............................74 Problems relating to images ...................................................... 75
 Problems when projection starts ................................................ 80
 Other problems .......................................................................... 81 
						

							69
Using the HelpIf a problem occurs with the projector, the Help function uses on-screen 
displays to assist you in solving the problem. It uses a series of menus in a 
question and answer format.
PROCEDURE
Press the [Help] button.
The help menu will be displayed.Select a menu item.
If using the control panel, the [ Select ] buttons function as 
the up and down keys.
If using the remote control, press the [ ] and [ ] buttons to 
select an item.
Confirm the selection.
Press the [Enter] button to confirm the selection of a menu item.
1
Projector
2
Remote control Projector
3
Remote control Projector