Epson Projector Emp 5300 User Manual

Turning the Equipment On and Off
n  n  n  n  n  n
31
Turning the Equipment On and Off
Always turn on the projector and its attached equipment in 
the following order.
1. Video source
2. Audio source (if different than computer or video source)
3. Projector
4. External speaker or PA system
5. Computer
Turning the Projector On and Off
1. Remove the projector lens cap.
2. Press the Power button on the remote control or control 
panel. The green power indicator comes on.
If computer or video equipment is...

Using the Projector
  n  n  n  n
32
Reverse the order shown above to turn off the projector and 
other equipment. After you press the Power button to turn 
off the projector, the fan will remain on and the operation 
indicator will flash orange for about one minute as the 
projector cools.
 The indicator stops blinking (and remains lit in orange) when 
the cooling operation is complete.
¨
Note: The projector is designed so that it cannot be turned back 
on while the power indicator is flashing green....

Focusing and Positioning the Screen Image
n  n  n  n  n  n
33
Focusing and Positioning the Screen 
Image
After an image appears on the screen, check to see if it is in 
focus and whether it fits properly on the screen.
• To adjust the focus of the image, rotate the focus ring, 
which is the outer ring on the projector’s lens. 
• To adjust the size of the image, rotate the inner zoom ring. 
Rotate the zoom ring clockwise to make the image larger, 
and counterclockwise to make it smaller.
zoom ringfocus ring 

Using the Projector
  n  n  n  n
34
If you need to raise or lower the image on the screen, extend 
or retract the two feet at the bottom of the projector as 
follows.
1. Stand behind the projector and support the front of it 
while you lift the foot adjuster lever located above the feet. 
This unlocks the feet so they can move up and down 
freely. Do not let the projector drop.
¨
Caution: Do not hold the projector by the lens as you may 
damage it.
2. While lifting the foot adjuster lever, raise or lower...

Focusing and Positioning the Screen Image
n  n  n  n  n  n
35
Resize Button 
The Resize button allows you to select the projection screen 
mode for certain types of image input signals from a 
computer.
EMP-7300/7200
With images up to XGA size(1024x768 pixels), you can 
choose from two projection methods. Either display the 
image in the center of the projection area(Window display) or 
display the image full size(Resize display).
You can also choose from two projection methods with 
images greater than...

Using the Projector
  n  n  n  n
36
Controlling the Projector
Normally you control the projector using the remote control. 
The buttons on the remote control allow you to do the 
following:
• Switch power on and off.
• Auto-set-up of the computer image screen.
• Switch between input images (Computer 1, Computer 2, 
video-computer).
• Access menu for adjustment of image, audio, video, and 
display settings.
• Control resizing.
• Control display freeze.
• Control display blanking.
• Adjust and mute audio...

Controlling the Projector
n  n  n  n  n  n
37
Using the Remote Control
When using the remote control, always point it towards the 
remote control receivers located at the front and at the back 
of the projector.
To be able to use the remote control as a cordless mouse 
connect the projector to your computer with all cables came 
with the EMP-7300/7200/5300.
To use the remote control, always point it towards the remote 
control receivers located at the front of the projector.
You can use the remote...

Using the Projector
  n  n  n  n
38
In addition to the remote control, you can also control the 
projector by using the buttons on the projector’s operation 
panel located on top of the projector.
This table summarizes the functions on the remote control.   
* When the computer 2/5 BNC switch on the back of the projector is turned to 5 
BNC, the source is switch to 5 BNC.
Button Function
Menu Displays or hides the menu.
Source Switches to Computer 1 , Computer 2*, or Video.
Pointer button Use the pointer...

Controlling the Projector
n  n  n  n  n  n
39
Using the Control Panel
You can use the control panel to control the printer instead of 
the remote control. However, you can program and access the 
custom features only when you are using the remote control. 
Power
Blank Source
Resize
Menu
MuteVolume
Sync.
Sync.
TrackingTracking
Enter button
Operation Panel 

Using the Projector
  n  n  n  n
40
The following table summarizes the functions on the control 
panel.   
* When the computer 2/5 BNC switch on the back of the projector is turned to 5 
BNC, the source is switch to 5 BNC.
Button Function
Power Starts or stops projection.
Source Switches to Computer 1 , Computer 2*, or Video.
Menu Displays or hides the menu.
Up, down arrows 
(Sync+/Sync-)Synchronizes the computer’s graphic signal.
Use these buttons to adjust an overall image that is 
fuzzy or streaked,...