Epson Projector Emp 51 User Manual

49
Advanced Menu
Displaying Menus
Press the Menu button, use the Enter button to select Advanced from the top 
menu displayed, and press the Enter button to move to a submenu.
Settings
MenuContent
Language Select the menu language.
Select from Japanese, English, German, French, Italian, Spanish, 
Portuguese, Chinese and Korean.
Color Setting Use color temperature or RGB to create settings for the colors displayed 
on screen. 
Color Temp: Adjusts the color temperature
* of the video.  
Select Color Temp...

50
About Menu
Displaying Menus
Press the Menu button, use the Enter button to select About from the top 
menu displayed, and press the Enter button to move to a submenu.
Setting and Display Information
The settings information displayed in the About menu differs as shown below 
during video projection from a computer/component versus a video device.
D-Sub15: Computer/Component video  Video: Video image
: Display   : No display
MenuContentVideo Projection
D-Sub15Video
Lamp Displays cumulative lamp-on...

51
Reset All Menu
Displaying Menus
Press the Menu button, and use the Enter button to select Reset All from the 
top-level menu displayed.
Settings
MenuContent
Reset All Returns all menu settings to initial settings.
(Lamp and language settings excluded)
* Note that rear and invert settings will also be cleared by this 
operation. 

52
Initial Settings List
Initial settings at product shipment are shown below.
Main Menu TitleSubmenu TitleInitial Settings
Video (Computer/
Component Video)Position Central value
Tracking Dependent on the connected signal
Sync. 0
Brightness
Central value Contrast
Sharpness
Gamma Normal
Input Signal RGB
Auto Setup ON
Aspect Ratio 4:3
Video (Video) Position
Central value Brightness
Contrast
Color
Tint
Sharpness
Gamma Normal
Mode Auto
Aspect Ratio 4:3
Audio Volume
Central value
Tone
Audio Input Auto
Effect...

53
Troubleshooting
Possible Failures ..................................................... 54
When Indicators Do Not Help ................................ 57 

54
Possible Failures
If you think your projector may have failed, first check the indicators on the 
unit.
Your projector includes an operation display indicator and a problem/alarm 
display indicator which provide information on projector status.
Operation Display Indicator 
Indicator 
StatusCauseRemedy or StatusSee 
Page
Steady 
orangeStandby 
status(Not abnormal)
Press the Power button to begin projection.24
Flashing 
orangeCool-down 
in progress(Not abnormal)
Please wait.
Cool-down
* time takes about...

55
Problem and Alarm Display Indicator 
Indicator 
StatusCauseRemedy or StatusSee 
Page
Steady red High 
internal 
temperatureThe lamp will turn off automatically and projection 
will stop. Wait for about 5 minutes without operating 
the projector. After 5 minutes, disconnect the power 
plug and connect it again.
If the projector overheats, check the following two 
points.
Is the setting-up location well ventilated?
Check that the air inlet and air outlet are clear, and 
that the projector is not...

56
Tip:
 If the indicator is normal but you experience problems with video projection, refer to 
When Indicators Do Not Help on the following page.
 If an indicator is showing a status which does not appear in the previous tables, 
contact your dealer or the nearest address provided at “International Warranty 
Conditions” in “Safety Instructions/World-Wide Warranty Terms” included in the 
package.
Flashing 
orangeHigh-speed 
cooling in 
progressNot a problem, but projection will be interrupted...

57
When Indicators Do Not Help
Video is Not Projected
[Nothing is Displayed]
• Is the lens cover still on?  See page 24
 Have you turned the power off and then immediately 
on?  See page 31
The Power button cannot be operated immediately  after the 
projection has been switched off.  The Power button 
becomes operable after cool-down
* is complete.
 Is Sleep Mode on?  See page 48
If Sleep Mode is set to on and no video signal is input for 30 
minutes, the projector lamp shuts off automatically.
 Is...

58
Carefully review sections such as Providing External 
Output and Providing Output to an Externally Connected 
Monitor in the instruction manual of the connected 
computer.
Image is Unclear
 Is the focus adjusted correctly?  See page 29
 Is the projection distance optimal?  See page 16
The recommended projection distance is 39.37inches (1.0m)  
to 515.75inches (13.1m). Set up the projector in this range.
 Is the lens dirty?  See page 64
 Is the projection beam facing the screen directly?  
See page...