Epson Projector Emp 51 User Manual

29
Adjusting the Focus
This section describes how to adjust the video focus.
1.Turn the focus ring on the projector to adjust 
the focus.
Tip:
 Focus cannot be achieved if the lens is dirty or 
covered with condensation.  Wipe off any dirt 
or condensation (See page 64).
 If adjustment does not succeed, make sure the 
setup distance is between 39.37inches (1.0m)  
and 515.75inches (13.1m).
Keystone Correction (Using Projector Button)
When the foot adjust levers are used to change the projection angle,...

30
Adjusting Images (Remote Control Only)
[Optimizing Computer Video (Using the Auto button)]
This function applies automatically optimized adjustment values to a 
computer input signal.
If the input is a video signal, this function does not operate.
Adjusted values set automatically are Tracking, Position (vertical and 
horizontal), and Sync.
Tip:
 This function cannot optimize the adjustment 
for some signal types.  In these cases, use the 
Video Menu commands to perform adjustment 
(See page 43).
...

31
Ending After the Projection
Ending
1.Press the Power button.  A Power Off 
confirmation message is displayed.
2.Press the Power button again.
The projector lamp goes out, the operation 
display indicator flashes orange, and after 
cool-down
* is complete, the indicator 
switches to steady orange.
Tip:
If you do not wish to shut the power, press 
another button.
Or, if no action is taken, the message disappears 
after 7 seconds.
3.Check that the operation display indicator 
lights orange.
Tip:
 The...

32
4.Pull the power cord plug out of the outlet.
Caution:
Do not pull the power cord plug out of the outlet 
while the operation display indicator is flashing 
orange.  This may cause a malfunction or 
shorten the projector lamp life.
5.Set the remote control R/C switch to Off.
Tip:
Unless the remote control R/C switch is switched 
off, a small amount of current will be supplied to 
the remote control and exhaust the batteries.  If 
the remote control will not be used for a long 
period or you are moving...

33
What You Can Do
Using the Wireless Mouse ...................................... 34
Enlarging an Image................................................. 36
Adjusting Image Size.............................................. 37
Adding Image Effects ............................................. 38
Freezing and Deleting Images ................................ 39
Displaying Help Screens ........................................ 40 

34
Using the Wireless Mouse
The remote control included allows you to control a computers mouse 
operations at a separate location.
The Enter button has the same action as a left mouse button, and the Esc button 
has the same action as a right mouse button.
Mouse operation by remote control allows you to make a presentation at the 
screen without assistance.
Presenter
Unassisted presentation is possible
Tip:
 If mouse button functions are swapped on your 
computer, the functions on the remote control...

35
Making a Connection
Before making a connection, switch off power to the projector and computer.
Caution:
 Connecting a non-USB mouse cable with the power on can cause malfunction or 
failure.
 Use only the mouse cable supplied.  Any other cable may cause failure.
When using a USB mouse, note the following.
 Windows
The only compatible models are those pre-installed with the standard USB 
interface configuration in Windows2000/Me and Windows98.
If the computer is running a version of Windows...

36
Enlarging an Image
The remote control included lets you enlarge portions of an image.
1.Press the E-Zoom button on the remote 
control to enlarge or reduce the display on 
screen.
(The Esc button releases this feature.)
Tip:
24-step partial enlargement and reduction by 
factors of 1x-4x is available.
2.Tilt the Enter button up, down, left or right 
to scroll the projected image in that 
direction.
Magnification factor is displayed.
Reduction Enlargement
Push up
Push downPush right Push left 

37
Adjusting Image Size
The Wide/Tele button on the projector allows you to adjust the size of images.
1.When you press the T (Tele) side of the 
button, the images are reduced.
2.When you press the W (Wide) side of the 
button, images are enlarged.
Tip:
 The enlargement/reduction ratio for 
adjustment with the Wide/Tele button is 
0.8 – 1.0 in 32 steps.
 This function is active until the Reset All menu 
is executed (See page 51). 

38
Adding Image Effects
Using the Effect1 and Effect2 buttons, you can add effects to images during 
presentation (to cancel this function, press the Esc button).
For effects settings, see Effect Menu (page 46).
Cursor/Stamp
This effect displays a cursor on the screen and freezes it at a desired location.
1.Press the Effect1 button to display a cursor.
2.Tilt the Enter button to move the cursor to a 
desired position.
3.Press the Enter button, and the cursor 
position is displayed as a stamp.
Tip:
...