Epson Projector Emp 30 User Manual

9
Basic Operations
Turning Off the Projector
Follow the procedure below to turn off the power for the projector.
Procedure
1Turn off the power for the signal 
sources that are connected to the 
projector.
Check that the power for all connected 
components has been turned off.
2Press the [Power] button on either the 
projectors control panel or the remote 
control.
The confirmation message shown left will appear.
If you do not want to turn off the power, press any 
button except the [Power] button.
If you...

Turning Off the Projector
10
5
Retract the front adjustable feet if they 
are extended.
Gently push down on the projector while 
simultaneously pressing the two foot adjust 
buttons.
6Attach the lens cover.
Attach the lens cover to the lens when not using 
the projector, in order to stop the lens from 
getting dusty or dirty.
Foot adjust buttons
Lens cover 

11
Basic Operations
Adjusting the Screen Image
You can correct and adjust the screen image in order to obtain the best possible picture.
The size of the projected image is basically determined by the distance from the projector to the screen. 
(Setup Guide)
If further minor adjustment is required, press the [Zoom] button on the projectors control panel to make the 
adjustment. Minor adjustments can be made to the image size to between a zoom ratio of approximately
0.8 to 1.0 in 33 steps.
Procedure...

Adjusting the Screen Image
12
The projector should be set up so that it is as perpendicular to the screen as possible.
If it is not possible to set up the projector so that it is perpendicular to the screen, it can be set up at a slight 
vertical angle instead. You can extend or retract the front adjustable feet to adjust the projection angle within 
a maximum range of 10º.
ProcedureWhile pressing the two foot adjust 
buttons at either side, lift up the front of 
the projector so that the front...

13
Basic Operations
When the projector is tilted, it will cause keystone distortion to appear in the image, but this distortion can be 
corrected using the keystone correction function as long as the vertical angle of tilt is within a range of 
approximately 15º.
Procedure
Correcting Keystone Distortion
•
•• •When keystone correction is carried out, the projected image will become smaller.
•
•• •The keystone correction settings are memorised. If you change the position or angle of the 
projector, you may...

14
Adjusting the Image Quality
The quality of the screen images can be adjusted as follows.
When the accessory cinema filter is attached to the projector and the Cinema Filter command is set to 
ON, the images are adjusted to the optimum tint for movie theatre images.
If a computer is connected and the projector is being used for a presentation at such times, images will 
appear darker than normal, so remove the cinema filter and change the Cinema Filter setting to OFF.
Procedure
1Attach the accessory...

15
Basic Operations
The following six preset colour modes are available for use depending on the characteristics of the images 
that are being projected. You can easily obtain the optimum image quality simply by selecting the colour 
mode that corresponds to the projected images. The brightness of the images will vary depending on which 
colour mode is selected.
ProcedureThe colour mode changes as follows 
each time the [Color Mode] button on 
the remote control is pressed.
Normal → Meeting →...

Adjusting the Image Quality
16
Procedure
1
Press the [Menu] button on the remote 
control, and then select Aspect Ratio 
from the Video menu.
For details on this operation, refer to Using the 
Configuration Menus. (p.27)
2Press the [ ] and [ ] buttons to set the 
aspect ratio to either 4:3 or 16:9, 
and then press the [Enter] button.
3
After making the adjustment, press the [Menu] button to exit the configuration 
menu.
Automatic setup detects the status of the signals coming from the connected computer,...

17
Basic Operations
If vertical stripes appear in the projected images, and this cannot be fixed 
using automatic setup, you will need to adjust the tracking
 manually using 
the following procedure.
Procedure
1
Press the [Menu] button on the remote 
control, and then select Tracking from 
the Video menu.
For details on this operation, refer to Using the 
Configuration Menus. (p.27)
2Press the [ ] and [ ] buttons to set the 
tracking value.
The tracking value increases or decreases each 
time a button is...

Adjusting the Image Quality
18
If flickering, fuzziness or interference appear in images that are input from 
the computer, and this cannot be fixed using automatic setup, you will need to 
adjust the sync
 manually using the following procedure.
Procedure
1Press the [Menu] button on the remote 
control, and then select Sync. from 
the Video menu.
For details on this operation, refer to Using the 
Configuration Menus. (p.27)
2Press the [ ] and [ ] buttons to set the 
sync value.
The sync value increases...