Epson Projector EH-TW5350 User Manual

Adjusting the Image
40
Deleting a Saved Memory
a
Press the  button, and then select Erase Memory.
The Erase Memory screen is displayed.
b
Select the target memory name.
A confirmation message is displayed. If you select Yes, the content of the saved memory is erased.
c
When erasing all saved memories, perform Reset Memory. s Reset - Reset
Memory  p.74
Renaming a Memory
You can rename each memory name using up to 12 characters. Giving the memory a name that is easy to
remember is useful when loading the...

Adjusting the Image
41
d
Enter a new name.
Use the  buttons to select a character, and then press the  button to confirm
the selection. Enter up to 12 characters.
When you have finished entering the name, select Finish.
The memory name is changed. 

Useful Functions
42
Enjoying 3D Images
Preparing to View 3D Images
Check the following before viewing 3D images.
•The source is HDMI1 or HDMI2.
•Set 3D Display to Auto or 3D.
When 2D is set, press the 
 button on the remote control and switch to Auto or 3D. s Signal - 3D Setup - 3D
Display  p.66
•Pair 3D Glasses.  
s  p.44
This projector supports the following 3D formats.
•Frame Packing
•Side by Side
•Top and Bottom
If the 3D image cannot be viewed
The projector automatically projects a 3D image when...

Useful Functions
43
c
•I f  y o u  a r e  u s i n g  a  d e v i c e  o r  c a b l e  t h a t  d o e s  n o t  s upport 3D images, 3D projection cannot be performed.
•F o r  d e t a i l s  o n  3 D  f o r m a t  s e t t i n g s  o n  t h e  A V  d e v i c e ,  s e e  t h e  d o c u m e n t a t i o n  s u p p l i e d  w i t h  t h e  A V  d e v i c e .
•When the 3D format has not been correctly set up, an image will not be correctly projected as shown
below.
•If a 3D image is not projected correctly even...

Useful Functions
44
Attention
•Only connect to an electrical outlet that uses the voltage displayed on the adapter.
•Note the following points when handling the USB cable.
- You should not bend, twist, or pull the cable with too much force.
- You should not modify the cable.
- You should not perform wiring near an electric heater.
- You should not use the cable if it is damaged.
Pairing 3D Glasses
To view 3D images, you first need to pair the 3D Glasses with the projector.
Press the [Pairing] button for...

Useful Functions
45
Indicators Status
Flashes red two times ×5 Weak battery
Lit red Charging
Lit green Charging completed
Flashes green and red in turn Pairing
Lit green for ten seconds and then turns
offPower on or pairing succeeded
Converting 2D Images to 3D
You can convert 2D images from HDMI1 or HDMI2 into 3D images.
a
Press the  button to set 3D
Display to Auto.
The  button toggles 3D Display
between Auto, 3D, and 2D.
b
Press the  button, to display the
menu in the order Signal - 3D Setup
- 2D-to-3D...

Useful Functions
46
Warnings Regarding Viewing 3D Images
Note the following important points when viewing 3D images.
Warning
Disassembling or remodeling
•Do not disassemble or remodel the 3D Glasses.
This could cause a fire to occur or the images to appear abnormal when viewing, causing you to feel unwell.
Storage locations
•Do not leave the 3D Glasses or the supplied parts within reach of children.
They could be accidentally swallowed. If anything is accidentally swallowed, contact a doctor...

Useful Functions
47
Caution
Viewing Time
•When viewing 3D images, always take periodic breaks during extended viewing.
Long periods of viewing 3D images may cause eye fatigue.
The amount of time and frequency of such breaks varies from person to person. If your eyes still feel tired or
uncomfortable even after taking a break from viewing, stop viewing immediately.
Caution
Watching 3D Images
•If your eyes feel fatigued or uncomfortable when viewing 3D images, stop viewing immediately.
Continuing to view...

Useful Functions
48
Using the HDMI Link Function
HDMI Link Function
When an AV device that meets the HDMI CEC standards is connected to the projector's HDMI port, you can
perform linked operations such as linked power on and volume adjustment for the AV system from one
remote control.
c
•As long as the AV device meets the HDMI CEC standards, you can use the HDMI link function even if
the AV system in-between does not meet the HDMI CEC standards.
•Up to 3 multi-media players that meet the HDMI CEC...

Useful Functions
49
c
To use the HDMI Link function, you must configure the connected device. See the documentation
supplied with the connected device for more information.
Connecting
You can check the connected devices that are available for HDMI Link, and select on the device you want to
project the image from. Devices that can be controlled by HDMI Link automatically become the selected
device.
Before displaying the list of connected devices, check that HDMI Link is set to On. 
s Settings - HDMI
Link...