Epson Projector Eb W8d User Manual

49
Advanced Operations
Connecting with a component video cable
Connecting with an HDMI cable
Use a HDMI cable that meets the HDMI standard. Otherwise, the image may not be displayed clearly or lost.
For a D port output device, use a commercially available D port - component conversion cable.
PCM Audio is supported. If no audio is output, set the destination device to the PCM out mode.
RCA audio cable 
(commercially available) To Audio input 
port
White
Output
Audio L
RRed
Component video cable...

50
This unit automatically detects input signals and changes the projected image.
The projector automatically detects signals being input from connected equipment, and the image being input from the 
equipment is projected.
You can project the target image quickly as input ports with no image signal being input are ignored when you change by 
pressing the
  .
1Open the lens cover and press  .
2Turn the device power switch on, and press the [Play] or 
[Playback] button on the video device.
3Press  to...

51
Advanced Operations
When a computer image is not projected
You can switch the image signal destination from the computer by holding 
down   and pressing   (the key is usually labeled   or  ). 
s Computer “Documentation”
After switching, wait a few seconds for projection to start.
Depending on the computer, each time the key to change the output is pressed, 
the display status may also change as follows.
Examples of Switching Output
Epson Toshiba
NEC IBM/Lenovo
Panasonic Sony
SOTEC Dell
HP Fujitsu...

52
Connecting commercially available headphones.
Audio Settings
Caution
•When listening with headphones, make sure the volume is not too high. You may damage your hearing when 
listening to sounds at high volume over an extended period of time.
•Do not set the volume too high from the outset. A loud sound may be produced suddenly that may cause damage 
to your headphones or your hearing. As a precaution, lower the volume before you switch off this unit then raise it 
gradually after you switch it back...

53
Advanced Operations
You can output microphone audio from the projectors speaker by connecting a microphone to the projectors Mic Input Port.
To adjust audio from the Mic input port, press   . 
•When the Mic Input Level is too low, adjust it using   . sp. 70
•You can select Mic Input Level from the Option page in the Visual Setup menu. 
sp. 63
The projector is compatible with a dynamic mic. It does not support plug-in-power type.
Connecting a microphone
To Mic Input Port 

54
You can connect to AV amplifiers and so on or equipment capable of making digital recordings when they are equipped 
with a coaxial digital audio input port. When connecting, use a commercially available coaxial digital cable.
When you turn the Virtual surround sound function on, you can enjoy real 
stereo sound although sound is usually provided through multiple speakers.
1Press .
The current settings are displayed on the screen.
2Select the desired settings by pressing   repeatedly.
The signal being...

55
Advanced Operations
You can select the sound effects appropriate to the musical genre of the current 
disc.
1Press .
The current settings are displayed on the screen.
2Select the desired settings by pressing   repeatedly.
The sound effects, which you can select according to the inserted disc or 
the connected source, are switched as follows: 
Select “Concert” or “Classic” sound effects for flat sound output.
Selecting the digital sound effects
Set the [Function] position before 
performing operations...

56
Settings and 
Adjustments
The settings of this unit can be adjusted to suit the environment in which it is used.
1Press   during playback or when stopped.
The following setup menu is displayed.
2Press   and select the desired icon.
Setup Menu Operation and 
Functions
Using the setup menu
Language 
setup
Others setup Audio setup 

57
Settings and 
Adjustments
3Press   to select the item to be set, and then 
press .
The settings are displayed on the right.
4Select the setting you wish to change, and press  .
To display other setting pages, select a desired icon by repeatedly 
pressing .
5After setup is complete, press   to close the setup menu.
Language page
Eject the disc before the setup. You cannot make the setting below when a disc is inserted.
Setting ItemSetting Contents
Disc Menu
Select the DVD video menu language.For “6978”...

58
Audio page
Others page
Setting ItemSetting Contents
Digital Output
Select the kind of output signal according to 
the equipment connected to the Digital 
Coaxial Audio-Out port.
For detailed information sp. 60All: Use when connected to a DTS/Dolby Digital Decoder, 
or when connected to equipment with these functions.
PCM Only: Use when connected to equipment that is only 
compliant with Linear PCM.
Night Mode
Compensates for the variation in the way we 
hear loud and quiet sounds when playing back 
at...