Epson Projector BrightLink Pro 1430Wi User Manual

							Setting a Password
To use password security, you must set a password.
1. Hold down the Freezebutton on the remote control for about ten seconds or until you see this menu.
2. Press the down arrow to select Passwordand pressEnter.
You see the prompt Change the password?.
3. Select Yesand press Enter.
4. Press and hold down the Numbutton on the remote control and use the numeric buttons to set a
four-digit password.
The password displays as **** as you enter it. Then you see the confirmation prompt.
5. Enter the password again. You see the message Password accepted.
6. Press Escto return to the menu.
151  
						

							7. Make a note of the password and keep it in a safe place in case you forget it.
Parent topic:
Password Security Types
Selecting Password Security Types After setting a password, you see this menu, allowing you to select the password security types you want
to use.
If you do not see this menu, hold down the Freezebutton on the remote control for five seconds until the
menu appears.
1. To prevent unauthorized use of the projector, select Power On Protection, pressEnter, selectOn,
press Enter again, and press Esc.
2. To prevent changes to the Users Logo screen or related display settings, select Users Logo
Protection, press Enter, selectOn, pressEnteragain, and press Esc.
3. To prevent changes to network settings, select Network Protection, pressEnter, selectOn, press
Enter again, and press Esc.
4. To prevent changes to the projectors time or schedule settings, select Time/Schedule Protection,
press Enter, select On, pressEnteragain, and press Esc.
You can attach the Password Protect sticker to the projector as an additional theft deterrent.
Note: Be sure to keep the remote control in a safe place; if you lose it, you will not be able to enter the
password required to use the projector.
Parent topic: Password Security Types
Related references
Projector Feature Settings - Settings Menu
152 
						

							Projector Network Settings - Network Menu
Related tasks
Turning On the Projector
Saving a Users Logo Image to Display
Related topics
Scheduling Projector Events
Entering a Password to Use the Projector If a password is set up and a Power On Protectionpassword is enabled, you see a prompt to enter a
password whenever you turn on the projector.
You must enter the correct password to use the projector.
1. Press and hold down the Numbutton on the remote control while you enter the password using the
numeric buttons.
153  
						

							The password screen closes.
2. If the password is incorrect, the following may happen: • You see a wrong password message and a prompt to try again. Enter the correct password toproceed.
• If you enter an incorrect password several times in succession, the projector displays a request code and a message to contact Epson Support. When you contact Epson Support, provide the
displayed request code and proof of ownership for assistance in unlocking the projector.
Parent topic: Password Security Types
Related tasks
Selecting Password Security Types
Saving a Users Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on. You can
also display the image when the projector is not receiving an input signal or when you temporarily stop
projection (using the A/V Mute feature). This transferred image is called the Users Logo screen.
The image you select as the Users Logo can be a photo, graphic, or company logo, which is useful in
identifying the projectors owner to help deter theft. You can prevent changes to the Users Logo by
setting up password protection for it.
1. Display the image you want to project as the Users Logo.
2. Press theMenubutton, select the Extendedmenu, and press Enter.
154 
						

							3. Select the
Users Logosetting and press Enter.
You see a prompt asking if you want to use the displayed image as a users logo.
4. Select Yesand press Enter.
You see a selection box overlaying your image.
5. Use the arrow buttons on the remote control to surround the image area you want to use as the Users Logo and press Enter.
You see a prompt asking if you want to select this image area.
6. Select Yesand press Enter. (If you want to change the selected area, select No, pressEnter, and
repeat the last step.)
You see the Users Logo zoom factor menu.
7. Select a zoom percentage and press Enter.
You see a prompt asking if you want to save the image as the Users Logo.
8. Select Yesand press Enter.
Note: It takes a few moments for the projector to save the image; do not use the projector, its remote
control, or any connected equipment until it is finished.
You see a completion message.
9. Press Escto exit the message screen.
10. Select the Extendedmenu and press Enter.
11. Select Displayand press Enter.
155 
						

							12. Select when you want to display the Users Logo screen:
• To display it whenever there is no input signal, select Display Backgroundand set it toLogo.
• To display it whenever you turn the projector on, select Startup Screenand set it toOn.
• To display it whenever you press the A/V Mutebutton, select A/V Muteand set it to Logo.
To prevent anyone from changing the Users Logo settings without first entering a password, set a
password and enable Users Logo security.
Parent topic: Password Security Types
Related tasks
Setting a Password
Locking the Projectors Buttons You can lock the buttons on the projectors control panel to prevent anyone from using the projector. You
can lock all the buttons or all the buttons except the power button.
1. Press theMenubutton.
2. Select the Settingsmenu and press Enter.
3. Select the Control Panel Lock setting and pressEnter.
4. Select one of these lock types and press Enter:
• To lock all of the projectors buttons, select Full Lock.
156 
						

							• To lock all buttons except the power button, select
Partial Lock.
You see a confirmation prompt.
5. Select Yesand press Enter.
Unlocking the Projectors Buttons
Parent topic: Projector Security Features
Unlocking the Projectors Buttons If the projectors buttons have been locked, hold the Enterbutton on the projectors control panel for
seven seconds to unlock them.
Parent topic: Locking the Projectors Buttons
Installing a Security Cable You can install two types of security cables on the projector to deter theft.
• Use the security slot on the projector to attach a Kensington Microsaver Security system, availablefrom Epson.
• Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture.
Note: Do not pass drop-prevention cables through the security cable attachment point when mounting
the projector on a wall or ceiling.
Parent topic: Projector Security Features
157  
						

							Creating a User Pattern to Display
You can transfer an image to the projector and then display it as a pattern to aid in presentations when
you use the Pattern Display feature. This transferred image is called the User Pattern.
1. Display the image you want to project as the User Pattern from a connected computer or videosource.
2. Press the Menubutton, select the Settingsmenu, and press Enter.
3. Select the Patternsetting and press Enter.
4. Select the User Patternsetting and press Enter.
You see a prompt asking if you want to use the displayed image as a User Pattern.
5. Select Yesand press Enter.
Note: It takes a few moments for the projector to save the image; do not use the projector, its remote
control, or any connected equipment until it is finished.
You see a completion message.
6. Press Escto exit the message screen.
Parent topic: Adjusting Projector Features
158 
						

							Using the Interactive Features
Follow the instructions in these sections to use your projectors interactive features.
Interactive Modes
Using the Interactive Pens
Using Finger Touch Interactivity
Using BrightLink With a Computer
Whiteboard Mode
Annotation Mode (PC Free)
Splitting the Screen
Interactive Modes The BrightLink interactive features turn any wall into an interactive whiteboard, either with or without a
computer. These interactive modes are available:
• In whiteboard mode, you can use one or both interactive pens or your finger (BrightLink Pro 1430Wi)to write on the projected whiteboard. You can split the screen and interact with the whiteboard and
another source. You can insert images from a thumbdrive or scanner and save, print, or email your
pages, without connecting a computer.
• In annotation mode (PC Free Annotation), you can annotate over content projected from a computer, tablet, document camera, or other source. You can capture your annotated pages, then save or print
them. You can even split the screen and annotate on two images at the same time, using one or both
pens.
• In PC Interactive mode, you can use the interactive pen or your finger (BrightLink Pro 1430Wi) as a mouse to navigate, select, and scroll through content from your computer. You can split the screen
and interact with two projected images at the same time.
Note: You can also use the Easy Interactive Tools software to provide additional interactive features,
such as saving your annotations and printing them. See the online Easy Interactive Tools Operation
Guide for detailed instructions.
Parent topic: Using the Interactive Features
Related concepts
Whiteboard Mode
Using BrightLink With a Computer
159 
						

							Annotation Mode (PC Free)
Using the Interactive Pens The BrightLink interactive pens turn any wall into an interactive whiteboard, either with or without a
computer.
• With a computer, you can use Easy Interactive Tools. This software lets you use the pen as a mouseto annotate, save, and interact with content from your computer. Two people can annotate at the same
time.
• Without a computer, you can use the built-in toolbar. This lets you annotate images from a document camera, iPad, DVD player, or other source.
Follow the instructions in these sections to use the interactive pens.
Using the Pens
Pen Calibration
Parent topic: Using the Interactive Features
Related concepts
Easy Interactive Tools
Related tasks
Selecting a Networked Device Source
Using the Pens Your projector came with a blue pen and an orange pen, identified by the color on the end of the pen.
You can use either pen, or both pens at the same time (one of each color), with Easy Interactive Tools.
Make sure the pen batteries are installed.
160