Epson Projector BrightLink Pro 1430Wi User Manual

Setting
OptionsDescription
Net. Info - Wireless LAN Connection mode Displays wireless network status
and details
Wireless LAN Sys.
Antenna level
Projector Name
SSID
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Net. Info - Wired LAN Projector NameDisplays wired network status
and details
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Network Configuration Accesses additional network Configures your network settings
menus
Parent topic: Adjusting the Menu Settings
Related references...

Projector Setup Settings - ECO Menu
Settings on the ECO menu let you customize projector functions to save power. When you select a
power-saving setting, a leaf icon appears next to the menu item.
Setting OptionsDescription
Power Consumption AutoSelects the brightness mode of
the projector lamp
Normal
Auto: sets the projector to sense
ECO
the optimum lamp brightness and
adjust the lamp brightness
accordingly
Normal: sets maximum lamp
brightness
ECO: reduces lamp brightness
and fan noise, and saves power...

Setting
OptionsDescription
Sleep Mode OnAutomatically places the
projector in standby mode after
Off
an interval of inactivity
Sleep Mode Timer 1 to 30 minutesSets the interval for Sleep Mode
A/V Mute Timer OnAutomatically turns off the
projector after 30 minutes ifA/V
Off
Muteis enabled
Standby Mode Communication OnEnable this setting to allow the
following operations to occur
Communication Off
when the projector is in standby
mode:
• Monitor and control the
projector over a network
• Output audio and...

Projector Information Display - Info Menu
You can display information about the projector and input sources by viewing the Info menu. However,
you cannot change any settings in the menu.
SelectVersion to display the projectors firmware version. Select Projector Infoto display the settings
described below.
Note: Available settings depend on the current input source. The lamp usage timer does not register any
hours until you have used the lamp for at least 10 hours.
Information item Description
Lamp Hours...

Information item
Description
Refresh Rate Displays the refresh rate of the current input source
Sync Info Displays information that may be needed by a service technician
Status Displays information about projector problems that may be needed
by a service technician
Serial Number Displays the projectors serial number
Event ID Displays the Event ID number corresponding to a specific projector
problem; see the list of Event ID codes
Event ID Code List
Parent topic: Adjusting the Menu Settings
Event ID Code...

Event ID code Cause and solution
0479
A projector system error has occurred. Turn the projector off and then on again.
04FF
0891 Cannot find an access point with the same SSID. Set your computer, access point,
and projector to the same SSID.
0892 The WPA/WPA2 authentication type does not match. Make sure the wireless
network security settings are correct.
0893 The WEP/TKIP/AES encryption type does not match. Make sure the wireless
network security settings are correct.
0894 Communication with...

Projector Reset Options - Reset Menu
You can reset most of the projector settings to their default values using the Reset Alloption on the
Reset menu.
You can also reset the projectors lamp usage timer to zero when you replace the lamp using the Reset
Lamp Hours option.
You cannot reset the following settings using the Reset Alloption:
• Input Signal
• Users Logo
• Language
• Network menu items
• Lamp Hours
• Password
• Zoom
• Image Shift
Parent topic: Adjusting the Menu Settings
257 

Maintaining and Transporting the Projector
Follow the instructions in these sections to maintain your projector and transport it from place to place.
Projector Maintenance
Transporting the Projector
Projector Maintenance Your projector needs little maintenance to keep working at its best.
You may need to clean the projection window and obstacle sensor periodically, and clean the air filter
and air vents to prevent the projector from overheating due to blocked ventilation.
The only parts you should...

• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the
projection window.
Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the
projector lamp may cause a fire.
Caution: Do not use canned air, or the gases may leave a flammable residue.
Parent topic: Projector Maintenance
Related tasks
Turning Off the Projector
Cleaning the Obstacle Sensor Clean the projectors obstacle sensor glass (circled in red) periodically, or if...

Caution:
Do not use canned air, or the gases may leave a flammable residue.
Parent topic: Projector Maintenance
Related tasks
Turning Off the Projector
Cleaning the Projector Case Before cleaning the projector case, turn off the projector and unplug the power cord.
• To remove dust or dirt, use a soft, dry, lint-free cloth.
• To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquiddirectly on the projector.
Caution: Do not use wax, alcohol, benzene, paint thinner,...