Epson Projector BrightLink 1430Wi User Manual

Note:
The pen turns off automatically after 20 minutes of inactivity. Tap the pen tip or press the button on
the side to turn the pen back on.
1 Pen tip
2 Battery light
3 Power/function button
4 Attachment for optional strap or cord
5 Battery cover
• To turn on the pen, tap the pen tip or press the power/function button. Note: If you press the button, the battery light flashes briefly, then turns off. If the battery is low, the
battery light flashes continuously.
161  

• For best performance, hold the pen perpendicular to the board, as shown below. Do not cover the
black section near the tip of the pen.
• To write or draw on the projection surface in annotation mode or whiteboard mode, do the following: • To select a projected item, such as an icon, tap the projection surface with the pen tip.
• To draw on the projected screen, tap the projection surface with the pen and drag it as necessary.
• To move the pointer, hover over the surface without touching it.
• To...

• To use the pen as a mouse in PC Interactive mode, do the following:
• To left-click, tap the board with the pen tip.
• To double-click, tap twice.
• To right-click, press the power/function button on the side.
• To click and drag, tap and drag with the pen.
• To move the cursor, hover over the board without touching it.Note: If you do not want to use the hovering feature, you can turn it off using the Easy Interactive
Function setting in the projectors Extended menu.
Parent topic: Using the Interactive...

• Using the Image Shift feature
• Moving the projector
Note:
Move any pen you are not using away from the projection screen while calibrating.
Calibrating Automatically
Calibrating Manually
Parent topic: Using the Interactive Pens
Related tasks
Correcting Image Shape with the Keystone Buttons
Resizing the Image with the Wide and Tele Buttons
Adjusting the Image Position
Calibrating Automatically You do not need the pens or a computer for Auto Calibration.
Note:You can start Auto Calibration by pressing...

2. Select the
Easy Interactive Function setting and pressEnter.
3. Select Auto Calibration and pressEnter.
4. Adjust the image focus, if necessary.
5. Press Enterto select Yes.
A pattern appears then disappears, and the system is calibrated. If you see a message that
calibration failed, you need to calibrate manually.
165 

The cursor location and pen position should match after calibration. If not, you may need to calibrate
manually.
Parent topic:
Pen Calibration
Calibrating Manually If the cursor location and pen position do not match after auto calibration, you can calibrate manually.
1. Press theMenubutton, select the Extendedmenu, and press Enter.
2. Select the Easy Interactive Function setting and pressEnter.
166 

3. Select
Manual Calibration and pressEnter.
4. Adjust the image focus, if necessary.
5. Press Enterto select Yes.
A flashing green circle appears in the upper left corner of your projected image.
6. Touch the center of the circle with the tip of the pen. The circle disappears, and you see another circle below the first one.
167  

Note:
For the most accurate calibration, make sure you touch the center of the circle.
7. Touch the center of the next circle, then repeat. When you get to the bottom of the column, the next circle appears at the top of a new column.
Note: Make sure you are not blocking the signal between the pen and the interactive receiver (next
to the projection window on the projector).
If you make a mistake, press the Escbutton on the remote control to go back to the previous circle.
To restart the calibration...

Using Finger Touch Interactivity
You can use your finger to perform the same functions as the interactive pens when you install the
Touch Unit (BrightLink Pro 1430Wi).
Note:See the Installation Guide for detailed instructions on installing the Touch Unit.
Touch Unit Safety Instructions
Calibrating for Finger Touch Interactivity
Using Finger Touch Operations
Parent topic: Using the Interactive Features
Related concepts
Whiteboard Mode
Using BrightLink With a Computer
Annotation Mode (PC Free)
Related...

Follow these precautions when using the Touch Unit and finger touch interactivity:
• Children using finger touch interactivity should always be accompanied by an adult.
• Never disassemble or modify the Touch Unit.
• Do not look into the laser diffusion ports on the back of the Touch Unit. The laser can damage your
eyes. Extra care should be taken when children are present.
• Do not allow the laser light from the Touch Unit to pass through or be reflected by any optical devices, such as a magnifying...