Epson Projector 7350 User Manual

Connecting to a Computer
n  n  n  n  n  n
31
4. Connect the other plugs on the audio/video cable to the 
Audio jacks of the projector: insert the white plug into the 
L jack and the red plug into the R jack. Connect the plug 
at the other end of the audio/video cable to the audio 
output jacks of the video source. 
5. For S-Video, insert one end of an S-Video cable into the 
projector’s S-Video connector. Insert the other end into 
the S-video-out jack of your video source.
6. For component, insert three...

n  n  n  n  n
32
Connecting to an External Speaker or 
PA System 
  
Although the projector’s internal speakers are enough for 
most small- or medium-size rooms, you can connect the 
projector to an external speaker or public address (PA) system 
for large rooms or to gain maximum benefit from the 
projector’s built-in 3D sound function.
To connect the projector to an external sound system, you 
need to obtain an RCA-to-3.5 mm stereo audio cable. You 
can get one from your computer dealer.
1. Turn off...

  n     n        n     n     n    n     n     n    n    n     n     n      n      n      n
n  n  n  n  n  n
33
2
Using the Projector
This chapter provides the following information about using 
your projector:
• Turning the equipment on and off
• Focusing and positioning the screen image
• Controlling the projector with the remote control and the 
operation panel
• Monitoring the projector’s operating status 

n  n  n  n  n
34
The illustration below identifies the parts of your projector.
operation panel
operation indicator
zoom ring
focus ring
front foot
foot adjust lever speaker
remoto 
control 
receiverspeaker 

Turning the Equipment On and Off
n  n  n  n  n  n
35
Turning the Equipment On and Off
Turn on the projector and its attached equipment in the 
following order.
1. Video source
2. Audio source (if different from computer or video source)
3. Projector
4. External speaker or PA system
5. Computer
When you turn off the equipment, do so in the reverse order.
Turning the Projector On and Off
1. Remove the projector lens cap.
2. When you plug in the projector power cord, the power 
indicator flashes orange for...

n  n  n  n  n
36
After you press the power button to turn off the projector, a 
confirmation message appears. If you want to turn off the 
projector, press the power button again. If you don’t want to 
turn off the projector,press any button. The fan will remain 
on and the operation indicator will flash orange for about one 
minute as the projector cools down.
When the projector has cooled down, the operation indicator 
stops flashing and remains orange.
¨
Note: If you press the Power button to turn the...

Focusing and Positioning the Screen Image
n  n  n  n  n  n
37
Focusing and Positioning the Screen 
Image
When an image appears on the screen, check that it is in focus 
and correctly positioned on the screen.
• To focus the image, rotate the focus ring (the outer ring on 
the lens). 
• To adjust the size of the image, rotate the inner zoom ring. 
Rotate the zoom ring clockwise to make the image larger, 
or counterclockwise to make it smaller.
zoom ringfocus ring 

n  n  n  n  n
38
If you need to raise or lower the image on the screen, extend 
or retract the two feet at the bottom of the projector as 
follows:
1. Stand behind the projector and support the front of it 
while you lift the foot adjust levers above the feet. This 
unlocks the feet so they can move up and down freely. Do 
not let the projector drop.
¨
Caution: Do not hold the projector by its lens. This can damage 
the lens.
2. While lifting the foot adjust levers, raise or lower the 
projector until...

Focusing and Positioning the Screen Image
n  n  n  n  n  n
39
Resize Button 
The Resize button allows you to select the projection method 
for certain types of image input signals from a computer.
With images up to XGA (1024 ´ 768 pixels) size for the 
EMP-7350/7250 and SVGA (800 ´ 600 pixels) size for the 
EMP-5350, you can choose from two projection methods. 
You can either display the image in the center of the 
projection area(Window display) or display the image full 
size(Resize display).
You can...

n  n  n  n  n
40
Controlling the Projector
You can use the operation panel on top of the projector or the 
remote control to perform the following actions:
• Turn power on or off
• Auto set-up of the computer image
• Switch between input images (Computer 1, Computer 2, 
video-computer)
• Access the projector menus to adjust the image, audio, 
video, and display settings
• Control resizing
• Control display freeze
• Control display blanking
• Adjust or mute audio output
• Use custom functions
• Move the...