Epson Powerlite S5 Multimedia Projector Users Guide

							Fine-tuning the Projector61
Customizing Projector Features
The Settings menu lets you customize the way you use the projector, 
from adjusting lamp brightness and speaker volume to applying 
security controls. 
1. Press the 
Menu button.
2. Select the 
Settings menu. 
PowerLite S5 Series
PowerLite 77c 
						

							62Fine-tuning the Projector3. Press 
Enter. Then use the up and down arrow buttons and the 
Enter button to set the following options:
■Keystone
Adjusts a distorted image from a trapezoid shape to 
rectangular. 
■Auto Keystone (PowerLite 77c only)
Automatically adjusts a distorted image from a trapezoid 
shape to rectangular when the projector’s foot is extended or 
retracted. (Not available when you’re projecting from the 
ceiling or using rear projection.) Select 
ON or OFF.
■Zoom (PowerLite S5 Series only)
Adjusts the image size from Wide (larger) to Tele (smaller).
■Operation Lock
When turned on, this function disables all projector buttons, 
or all buttons except the P
Power button. Changes to this 
setting take effect after you restart the projector. (After you 
turn off the projector, wait for the Ppower light to turn a 
steady orange before turning it on again.) See page 71 for 
more information.
■Brightness Control
Select Low lamp brightness when the projection is too bright 
for the room. The 
Low setting also reduces electricity 
consumption and fan noise. Select 
High to project the 
maximum brightness. (Also check the 
Brightness setting in 
the Image menu; see page 56.)
■Volume
Adjusts the volume for the projector’s speaker.
4. When you’re finished, press 
Esc or Menu.
note
To cancel the Operation 
Lock function from the 
projector, press the 
Enter 
button for about seven 
seconds. 
						

							Fine-tuning the Projector63
Selecting Projector Setup Options
Use the Extended menu to customize the way you set up the 
projector. You can configure the projector for rear and/or ceiling 
projection, change the language for the menus and messages, set the 
screen background color, capture and store a custom image or logo for 
the startup screen.
1. Press the 
Menu button.
2. Select the 
Extended menu. You see the features and their settings 
on the right side:
3. Press 
Enter. Then use the up and down arrow buttons and the 
Enter button to set the following options:
■Display
Message: 
Lets you turn screen messages on or off.
Display Background: Sets the screen background to Black, 
Blue, or Logo when no signal is available.
Startup Screen: Enables or disables display of the startup 
screen when the projector is turned on.
A/V Mute: Sets the screen background to Black, Blue, or 
Logo when the A/V Mute button is pressed.
■User’s Logo
Turn on to display the image or logo you have captured 
whenever the projector is turned on. See page 67 for more 
information.
note
Logo settings cannot be 
changed if the User’s Logo 
Protect feature has been 
turned on. See page 68.
 
  
						

							64Fine-tuning the Projector
■Projection
Front:
 Projector is in front of the screen.
Front/Ceiling: Projector is in front of the screen, mounted 
upside-down from the ceiling.
Rear: Projector is behind the screen.
Rear/Ceiling: Projector is behind the screen, mounted 
upside-down from the ceiling.
To change from 
Front to Front/Ceiling or Rear to 
Rear/Ceiling, press and hold the A/V Mute button on the 
remote control for five seconds. 
■Operation
Direct Power:
 When this feature is enabled, projection starts 
as soon as you plug in the power cord. You don’t have to 
press the P
Power button. 
Sleep Mode: When Sleep Mode is on, the projector turns 
off the lamp if it has not received any input signals for a 
period of time (as defined in the Sleep Mode Time setting). 
Sleep Mode Time: When Sleep Mode is on, you can set the 
period of time before the projector turns off automatically, 
from 1 to 30 minutes.
Lens Cover Timer: This feature is enabled by default to turn 
the power off automatically when the 
A/V Mute slide is 
closed for more than 30 minutes. 
High Altitude Mode: When using the projector at an 
altitude above 4,900 feet (1,500 meters), turn this setting on 
to ensure that the internal temperature of the projector is 
regulated properly. Turn this setting off for lower elevations.
■Link 21L
Turn this setting on only if you’re controlling the projector 
from a computer with the EMP Link 21L software and the 
USB communication driver. This software can be 
downloaded from the Epson website at support.epson.com. 
(You must turn the projector off and then on again and 
connect a USB cable to use this setting.)
note
When Direct Power 
is turned on, press the 
P 
Power button to turn 
the projector off, wait until 
the P
power light turns a 
steady orange, then unplug 
the power cord. 
						

							Fine-tuning the Projector65
■Language
Select the language to be used for the projector menus.
4. When you’re finished, press 
Esc or Menu.
Viewing Lamp Usage and Other 
Information
Use the Info menu to view information about the display settings of 
your computer and the number of hours the lamp has been used.
1. Press the 
Menu button and select the Info menu. You see a screen 
displaying the following information:
■Lamp Hours
Displays the number of hours the lamp has been used. The 
life span of the lamp ranges from about 3000 hours in 
High 
brightness mode to about 4000 hours in 
Low brightness 
mode. If the number shown is close to 3000 or the 
information is displayed in red, make sure you have a spare 
lamp handy.
■Source
Displays the input source currently being projected.
■Input Signal (computer, RGB video, and component video)
Displays the input signal setting.
■Resolution (computer, RGB video, and component video)
Displays the input resolution.
■Video Signal (composite and S-Video)
Displays the video signal format.
■Refresh Rate (computer, RGB video, and component video)
Displays the refresh rate.
■Sync Info (computer, RGB video, and component video)
Provides information that may be needed by the service 
technician.
note
You can make changes to 
many of the signal settings on 
the Signal menu. See page 58 
for details.
note
The lamp usage timer doesn’t 
register until you’ve used the 
lamp for at least 10 hours. 
						

							66Fine-tuning the Projector
■Status
Displays information about projector problems. This 
information may be needed if service is required.
2. When you’re finished, press 
Esc or Menu.
Using the Projector’s Security Features
To prevent unauthorized use of the projector, you can do the 
following:
■Create an identifying user logo that is displayed at startup and/or 
when the 
A/V Mute button is pressed
■Assign a password
■Disable the projector’s buttons; this is useful, for example, if 
you’re projecting in a classroom and you want to ensure that no 
one touches the projector’s buttons while you’re using the remote 
control
■Install an anti-theft lock
If you create a user’s logo for the projector, you can lock the logo on so 
it is displayed as the startup screen and/or AV/Mute screen. 
Unauthorized users cannot turn it off or change it. This feature is 
intended to discourage theft and provides a way to identify the 
projector should it be stolen. 
If you assign the projector a password, a screen appears requesting the 
password whenever the projector is turned on. If you enter the 
password incorrectly three times in succession, the projector’s 
operation is locked and you’ll need to disconnect the power cord, then 
reconnect it to redisplay the password screen. If an incorrect password 
is entered 30 times in a row, the projector is locked and you’ll need to 
contact Epson to unlock it. See “Where To Get Help” on page 93.
When you enable the Operation Lock feature, all of the projector’s 
buttons are disabled except the P
 Power button.
note
If you should happen to 
enable the password before 
you set one and you see the 
prompt to enter the 
password, enter the default 
password 0000 to proceed. 
						

							Fine-tuning the Projector67
Creating Your Own Screen Logo
You can transfer any image on your computer to the projector, and 
then use it as the startup screen and/or the screen that is displayed 
when you press the 
A/V Mute button. The image can be a company 
logo, slogan, photograph, or any other image you want to use. The 
projector considers this image the “User’s Logo.” 
Follow these steps to capture the image and transfer it to the projector:
1. Display the image you want to use on the projector. You can use 
an image from either a computer or video source, such as a DVD 
player. 
2. Press the 
Menu button and select the Extended menu.
3. Use the down arrow button and press 
Enter to select User’s 
Logo
.
4. When you see a message asking if you want to use the present 
image as a user’s logo, select 
Yes and press Enter. A selection box 
displays over the image.
5. Use the arrow buttons on the projector or remote control to select 
the area of the image you want to use. Once you have selected the 
area, press 
Enter.
6. When you see the message 
Select this image?, choose Yes and 
press 
Enter. If you want to change the area selected, select No, 
press
 Enter and repeat steps 5 and 6. 
note
If the User’s Logo Protect 
function is 
ON, you see a 
message that the logo cannot 
be recorded. You’ll need to 
disable the User’s Logo 
Protect function before you 
can create or change the 
User’s Logo. See page 69. 
						

							68Fine-tuning the Projector7. When you see this screen, select a zoom rate (display size), and 
then press 
Enter. 
8. When you see the message 
Save image as user’s logo?, select 
Yes and press Enter. Saving the logo takes a few moments. Do 
not use the projector or other sources (computer, video, etc.) 
while the logo is being saved.
9. When you see the message 
Completed, press Esc.
10. To display the logo as the background screen when the 
A/V Mute 
button is pressed, select the 
Extended menu and press Enter.
11. Select 
Display and press Enter.
12. Select Display 
Background and press Enter. Then select Logo 
and press 
Enter.
13. When you’re finished, press 
Menu to exit the menus. 
Setting a Password 
1. Press the Freeze button on the remote control for about 7 seconds 
until you see the Password Protect menu:
note
The default setting for the 
Startup Screen option 
menu is 
ON. If the Startup 
Screen
 is set to OFF, the 
logo will not display at 
startup.
If the User’s Logo Protect 
function has been set to 
ON, 
the 
Display Background 
setting cannot be changed. 
You need to turn the protect 
function off first. See page 69 
for details.
Once you’ve saved a user’s 
logo, you cannot reset the logo 
setting to its factory default 
(no logo).
note
If a password has already 
been set, you see the 
Password Protect Release 
screen. See “Starting the 
Projector with a Password” 
on page 70. 
						

							Fine-tuning the Projector69
2. Select Password and press Enter. You see the message Change 
the password?
 
3. Select 
Yes and press Enter.
4. Enter a 4-digit number using the numeric buttons on the remote 
control, as shown. 
The password will be displayed as 
****. After you enter the last 
digit, a confirmation screen appears. Enter the password again. 
You see the message 
Password accepted.
5. After you finish setting the password, press the 
Esc button to 
return to the Password Protect menu.
Make a note of the password and keep it in a safe place in case you 
forget it. 
Turning On the Password and User’s Logo
1. Press the Freeze button on the remote control for about 
7 seconds until you see the Password Protect menu.
2. To enable the password, select 
Power On Protect and press 
Enter. Select ON then press Esc. 
3. To enable your screen logo, select 
User’s Logo Protect and press 
Enter. Select ON and press Enter. 
When this feature is on the logo appears whenever the projector is 
turned on (if the 
Startup Screen is enabled in the Extended 
menu; see page 63) and as the A/V Mute screen (if you selected 
the 
Logo as the Display Background in the Extended menu). 
None of the User’s Logo features can be changed when the User’s 
Logo Protect function is enabled.
4. Press 
Menu to close the Password Protect menu.
If you lose the remote control, you will not be able to enter the 
password, so keep the remote control in a safe place at all times.
You can attach the password protect sticker to the projector as an 
additional theft deterrent.
Numeric buttons on 
remote control 
						

							70Fine-tuning the Projector
Starting the Projector with a Password
When the password function is enabled, you see this screen when you 
turn on the projector:
Use the numeric buttons on the remote control to enter the password. 
Once you have entered the password correctly, the password screen 
closes, and projection begins.
If the password is not correct, you see the message 
Wrong password. 
Please try again.
 If you enter an incorrect password three times in 
succession, you see the message 
The projector’s operation will be 
locked. Request code xxxxx
 and the projector switches to standby 
mode for approximately 5 minutes. Write down the request code. 
Then disconnect the projector’s power cord from the electrical outlet, 
reconnect it, and turn the projector back on. 
When you see the Password Protect Release screen again, you can try 
to enter the correct password.
If you have forgotten the password, contact Epson with the request 
code number that appears in the Password Protect Release screen for 
assistance. See “Where To Get Help” on page 93.
If you enter an incorrect password 30 times in succession, the 
projector remains locked and you must contact Epson to have the 
projector serviced.