Epson Powerlite S1+ Users Guide

21
Connecting to Video Equipment For Component Video (DVD, Video games)
For RGB Video
Playing sound from video equipmentVolume adjustmentPress [l] or [r] on the remote control.
You can also adjust the volume with the configuration menu.
([Menu] button → “Setting” → “Volume”) See “
Setting menu
” on page 39
.
p
After projection starts, change the “Input Signal” setting in the “Image” 
menu to either “Component Video (YCbCr
g)” or “Component Video 
(YPbPr
g)” to match the signals from the video equipment....

22
Turning on the Projector Basic OperationTurning on the Projector 
1Connect the computer/video.
See “
Connecting to a Computer
” on page 14
, “Connecting to Video 
Equipment
” on page 20
.
2Remove the lens cover.3Attach the power cable to the projector.
4Insert the power plug into a wall socket.
The power indicator lights orange.
5Turn on the power of the computer/video.
If connected to a video source, start playback.
c
Turn off the power of the projector and the equipment you are connecting 
to.
p...

23
Turning on the Projector 
6Press the [Power] button.
The projector beeps and the power supply indicator begins to blink 
green.
7Wait until the power indicator lights green.
It takes about 35 seconds. 

24
Turning off the Projector Turning off the Projector
1Turn off the power to the computer/video equipment.
2Press the [Power] button.
The projector beeps and a confirmation screen is displayed.
3Press the [Power] button again.
The power indicator begins to blink.4Wait until the power indicator lights orange.
Cool-down
g takes place. It takes about 20 seconds.
5Unplug the projector from the outlet.
6Unplug the power cable at the projector.
7Replace the lens cover.
p
The confirmation screen disappears if...

25
Adjusting the Display Adjusting the DisplayAdjusting the projection sizeThe size of the projected image is basically determined by the distance from 
the projector to the screen. See “
Projection distance and screen size
” on 
page 12
.
1Press the [Wide] or [Tele] buttons on the control panel to adjust 
the projection size.
[Wide]: increase the size
[Tele]:   reduces the size
The image can be enlarged in this way to 1.2 times the normal size.
If you would like to enlarge the image further, move the...

26
Adjusting the Display Adjusting the projection angle
1Set up the projector so that it is at right angles to the screen.
If it is not possible to set up the projector so that it is at right angles to 
the screen, it can be set up at a slight vertical angle instead. (Max 
10°)2Raise the front of the projector while pressing the buttons on 
both sides.
3Extend the front feet and release the buttons when the projector 
is adjusted to the desired height.
Seen from the side
Center of 
lens
Seen from above...

27
Adjusting the Display KeystoneWhen the projector is not set at right angles to the screen, the display distorts 
in the shape of a trapezoid. This distortion can be corrected.
Press the [u] or [d] buttons.Images can be corrected without distortion when the projector is tilted to a 
maximum of ±15°.
p
You can correct only vertical distortion with this function. Horizontal 
distortion cannot be corrected.
p
 Screen size changes when keystone correction is performed.
 If the images become uneven in...

28
Selecting the Input Source Selecting the Input Source When a device is connected, projection commences automatically without 
having to select the input source, however when connected to two or more 
devices, you need to switch between the input sources. ProjectorThe input source changes each time [Source] is pressed.
The items selected using the “Input signal” command in the “Image” menu are 
displayed. See “
Image menu
” on page 36
.
Remote controlThe input source switches between Computer and...

29
Functions for Enhancing Projection Advanced OperationFunctions for Enhancing ProjectionAdjusting computer generated imagesThe computer signal is analyzed and the following settings are adjusted to 
ensure the optimum image quality.
◗Tracking
g
◗Position
◗Sync.
g
When Auto setup is set to off, press the [Auto] 
button on the remote control to perform auto 
setup.Adjust the Tracking and Sync settings manually if Auto setup cannot be 
performed. ([Menu] button → “Image” → “Picture Quality” → “Tracking,”...

30
Functions for Enhancing Projection The color mode changes each time you press the 
[Color Mode] button on the remote control.
Dynamic → Presentation →  Theatre → Living 
Room → sRGBDefault Value◗Computer input: Presentation
◗Other input: DynamicA/V MuteTemporarily stops the image and sound.
◗Press the [A/V Mute] button on the remote 
control. The sound and image disappear.
◗Projection is resumed when you press the 
[A/V Mute] button again or press the [Esc] 
button.
FreezePauses the projected images....