Epson Powerlite Pro Z8000wunl Users Guide

							List of Functions
71
*1 When inputting numbers and passwords, the following software keyboards are displayed. Use the [h] button on the remote control to move the cursor to the target 
key, and then press the [Enter] button. Enter figures by holding down the [Num] button on the Remote Control and pressing the numeric buttons. After inputting, 
select Finish on the keyboard to confirm your input. Select Cancel on the keyboard to cancel your input.
Each time the CAPS key is selected, it sets and changes between upper case 
and lower case letters. Each time the SYM1/2 key is selected, it sets and 
changes the symbol keys for the section enclosed by the frame. 
						

							List of Functions
72
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status of the projector. Items that can be displayed vary depending on the image 
signal being projected as shown in the following screen shots. 
Analog RGB/Digital RGB/
Component Video/Digital Component VideoComposite video/S-Video
Sub Menu
Function
Lamp HoursYou can display the cumulative lamp operating time
*.
When it reaches the lamp warning time, the characters are displayed in yellow.
Lamp StatusThe following icons show the status of the lamps.
 : Lighted  : Disable
When   is displayed, the lamp is not operating normally. See "Reading the Indicators". 
SourceYou can display the Source name for the connected equipment currently being projected. 
Input SignalYou can display the Input Signal selected in the Signal menu. 
ResolutionYou can display the Resolution. 
Video SignalYou can display the Video Signal selected in the Signal menu.
Refresh RateYou can display the Refresh Rate. 
Sync InfoYou can display the image signal Info.
This information may be needed if service is required. 
						

							List of Functions
73
* The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours and above is displayed as "10H", "11H", etc.
Reset Menu
StatusThis is Info about errors that have occurred on the projector.
This information may be needed if service is required.
Serial NumberDisplays the projector's serial number.
Sub Menu
Function
Reset AllYou can reset all items in the configuration menu to their default settings.
The following items are not reset to their defaults: Input Signal, User's Logo, Multi-screen, all items for Network menus, Lamp Hours, 
and Language. 
Sub Menu
Function 
						

							Projector Menu and Options List
74
Projector Menu and Options List
The table below summarizes the options you can select based on the 
projector menu you are viewing. Some options may not be available 
depending on the input source you are using.
For more information on these menus and options, read this chapter.
Menu
Options
Image Color Mode
Brightness
Contrast
Color Saturation
Tint
Sharpness
Abs. Color Temp.
Color Adjustment
Auto Iris
Reset
Signal Auto Setup
Resolution
Tracking
Sync.
Position
Progressive
Noise Reduction
DVI/HDMI Video Range
Input Signal
Video Signal
Aspect
Overscan
Reset
Settings Keystone
Control Panel Lock
Lens Operation Lock
Pointer Shape
Power Consumption
Remote Receiver
User Button
Test Pattern
Reset
Extended Display
Closed Caption
User’s Logo
Projection
Direction
Operation
Standby Mode
Air Filter Notice
Projector ID
Multi-screen
Language
Reset
Network Wired LAN
PJLink Password
Web Control Password
SNMP
Mail
AMX Device Discovery
Projector Name
Reset
Menu
Options 
						

							Projector Menu and Options List
75
Info Lamp Hours
Lamp Status
Source
Input Signal
Resolution
Video Signal
Refresh Rate
Sync Info
Status
Serial Number
Reset Reset All
Menu
Options 
						

							Projector Menu and Options List
76 
						

							77
Troubleshooting
This chapter explains how to identify problems and what to do if a problem is found.  
						

							Using the Help Screen
78
Using the Help Screen
If a problem occurs with the projector, press the [Help] button to display 
the Help screen. You can solve problems by answering the questions. 
ProcedureA
Press the [Help] button. 
The Help screen is displayed.
B
Select a menu item. 
Remote Control
Remote Control 
						

							Using the Help Screen
79
C
Confirm the selection. 
Questions and solutions are displayed as shown on the screen 
below.
Press the [Help] button to exit Help.
If the Help screen does not provide a solution to the problem, refer 
to "Problem Solving" p.80.
Remote Control 
						

							Problem Solving
80
Problem Solving
If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators". sp.81
If the indicators do not show clearly what the problem might be, refer to "When the Indicators Provide No Help". sp.86