Epson Powerlite Pro Z8000wunl Users Guide

							Positioning the Projector
21
16:10 image, Middle throw zoom lens 1 (ELPLM06)
57.6 to 87.6 ft
(17.6 to 26.7 m)22.8 to 34.8 ft
(6.9 to 10.6 m)11.2 to 17.2 ft
(3.4 to 5.2 m)Distance from screen
16:10 image, Middle throw zoom lens 2 (ELPLM07)
84.3 to 127.9 ft
(25.7 to 39.0 m)33.3 to 50.7 ft
(10.1 to 15.5 m)16.2 to 25 ft
(5.0 to 7.6 m)Distance from screen 
						

							Positioning the Projector
22
16:10 image, Long throw zoom lens (ELPLL07)
125.2 to 175.2 ft
(38.2 to 53.4 m)49.4 to 69.4 ft
(15.1 to 21.2 m)24.2 to 34.2 ft
(7.4 to 10.4 m)Distance from screen 
						

							Removing and Attaching the Interface Cover
23
Removing and Attaching the Interface CoverRemoving
Attaching
When you’ve finished connecting the projector to your equipment 
(sp.24) and plugging the power cord into the projector (sp.29), 
attach the interface cover as described below.
1 Loosen the screw.
2 While pulling up the interface cover open switch, pull the 
interface cover straight out.
1 Remove the top of the interface cover.
2 Install the cover along the guide.
3 Tighten the screws. 
						

							Connecting the Projector to Your Equipment
24
Connecting the Projector to Your EquipmentConnecting to a ComputerConnecting to the VGA Port
ProcedureA
Connect one end of the VGA computer cable to the 
projector’s Computer port, and the other end to your 
computer’s monitor port.
B
Turn the projector on (sp.29), select the image source 
(sp.38), and adjust the image (sp.30).
Make sure the Input Signal setting in the Signal menu is set to Auto or 
RGB. sp.62
Connecting to the BNC Ports
ProcedureA
Attach the BNC connectors on one end of your cable (not 
included) to the projector’s BNC ports. Connect the other 
end of the cable to your computer.
B
Turn the projector on (sp.29), select the image source 
(sp.38), and adjust the image (sp.30).
Make sure the Input Signal setting in the Signal menu is set to Auto or 
RGB. sp.62 
						

							Connecting the Projector to Your Equipment
25
Connecting to the HDMI Port
ProcedureA
Connect one end of your HDMI cable (not included) to the 
projector’s HDMI port, and the other end to your computer’s 
HDMI port.
B
Turn the projector on (sp.29), select the image source 
(sp.38), and adjust the image (sp.30).
Connecting to the DVI-D Port
ProcedureA
Connect one end of your DVI-D cable (not included) to the 
projector’s DVI-D port, and the other end to your computer’s 
DVI-D port.
B
Turn the projector on (sp.29), select the image source 
(sp.38), and adjust the image (sp.30). 
						

							Connecting the Projector to Your Equipment
26
Connecting to Video EquipmentConnecting to the HDMI Port
ProcedureA
Connect one end of your HDMI cable (not included) to the 
projector’s HDMI port, and the other end to the HDMI 
connector on your equipment.
B
Turn the projector on (sp.29), select the image source 
(sp.38), and adjust the image (sp.30).
Connecting to the DVI-D Port
ProcedureA
Connect one end of your DVI-D cable (not included) to the 
projector’s DVI-D port, and the other end to the DVI-D 
connector on your equipment.
B
Turn the projector on (sp.29), select the image source 
(sp.38), and adjust the image (sp.30). 
						

							Connecting the Projector to Your Equipment
27
Connecting a Component Video Source
ProcedureA
Connect one end of your cable (not included) to either the 
projector’s BNC ports or Computer port (depending on the 
type of component video cable you’re using). Connect the 
other end of the cable to your equipment.
B
Turn the projector on (sp.29), select the image source 
(sp.38), and adjust the image (sp.30).
Make sure the Input Signal setting in the Signal menu is set to Auto or 
Component Video. sp.62
Connecting an S-Video Source
ProcedureA
Connect one end of your S-Video cable (not included) to the 
projector’s S-Video port, and the other end to the S-Video 
connector on your equipment.
B
Turn the projector on (sp.29), select the image source 
(sp.38), and adjust the image (sp.30). 
						

							Connecting the Projector to Your Equipment
28
Connecting a Composite Video Source
ProcedureA
Connect one end of your cable (not included) to the 
projector’s Video port, and the other end to your 
equipment.
B
Turn the projector on (sp.29), select the image source 
(sp.38), and adjust the image (sp.30). 
						

							Turning the Projector On and Off
29
Turning the Projector On and Off
ProcedureA
Plug one end of the power cord into the projector, and the 
other end into an electrical outlet.
B
Remove the lens cover.
Warning:
Never look into the lens when the lamp is on. This can damage your eyes, and is 
especially dangerous for children.
C
Press the [
t
] power button on the remote control or on the 
back of the projector. 
						

							Adjusting the Image
30
Adjusting the ImageAdjusting the Position
ProcedureA
Press the [Lens Shift] button on the remote control or press 
the [Lens] button on the back of the projector until "Adjust 
Lens Shift" is displayed on the screen.
B
To adjust the position, use the [
h
] button on the remote 
control or the arrow buttons on the back of the projector as 
shown below.
Press the button repeatedly to make fine adjustments. Press and 
hold the button to make larger adjustments.
C
When you’re done, press the [Esc] button on the remote 
control or on the back of the projector.