Epson Powerlite Pro Z8000wunl Users Guide

Saving a User's Logo
111
Saving a User's Logo
You can save the image that is currently being projected as a User's Logo. 
When a User's Logo is saved, the previous User's Logo is erased and the 
logo cannot be returned to the factory default.
ProcedureA
Project the image you want to use as the User's Logo, and 
then press the [Menu] button. 
B
Select Extended - "User's Logo" from the configuration 
menu. s"Using the Configuration Menu"
If User's Logo...

Saving a User's Logo
112
D
Move the box to select the part of the image to use as the 
User's Logo. 
Your User’s Logo image can have a resolution up to 400^ 300.
E
When "Select this image?" is displayed, select Yes. 
F
Select the zoom factor from the zoom setting screen. 
G
When the message "Save this image as the User's Logo?" is 
displayed, select Yes. 
The image is saved. After the image has been saved, the message 
"Completed. " is displayed. 
Saving the user's...

Connecting a LAN Cable
113
Connecting a LAN Cable
Connect with a 100BASE-TX or 10BASE-T LAN cable (not included).
Caution:
To prevent malfunctions, use a category 5 shielded LAN cable.1 To LAN port
2 LAN cable (commercially available)
3 To LAN port 

Connecting to an external monitor
114
Connecting to an external monitor
Analog RGB images input through the Computer or BNC ports can be 
displayed on an external monitor and the screen at the same time. You 
can check projected images on an external monitor when giving 
presentations even if you cannot see the screen. Connect using the cable 
supplied with the external monitor.
Component video signals cannot be output to an external monitor. 
Additionally, signals input through any ports other than the...

Removing and Attaching the Projector Lens Unit
115
Removing and Attaching the Projector Lens UnitRemovingCaution:•Only remove the lens unit when necessary. If dust or dirt enter the projector, 
projection quality deteriorates and it could cause a malfunction.
•Try not to touch the lens with your hand or fingers. If fingerprints or oils are left on 
the surface of the lens, projection quality deteriorates.
•Before replacing the lens unit, use the lens shift function to horizontally and 
vertically center...

Removing and Attaching the Projector Lens Unit
116
C
Pinch the lock lever of the lens unit and turn it 
counterclockwise.
D
Once it is released, pull the lens unit straight out.
AttachingCaution:Do not remove or attach the lens unit when the projector's lens area is facing up (for 
projecting directly up). Dust or dirt could enter the projector.
ProcedureA
Insert the lens unit straight into the lens insertion section 
with the white circle on the lens on top. 

Removing and Attaching the Projector Lens Unit
117
B
While holding the lens unit firmly, turn the lock lever 
clockwise until it is locked. Check that the lens cannot be 
detached.
C
Replace the front cover.1 Install the cover along the guide.
2 Tighten the screw.
3 Tighten the two screws. 

Removing and Attaching the Projector Lens Unit
118
D
Replace the interface cover.
Caution:
•Install the front cover before using the projector.
•Store the projector with the lens unit installed.
If the projector is stored without the lens unit, dust and dirt may get inside the 
projector and cause malfunctions or lower the quality of projection. 1 Install the cover along the guide.
2 Tighten the screws. 

Reading Problem Mail Notification Function
119
Reading Problem Mail Notification Function
When the Mail Notification function is set to On and a problem/ 
warning occurs in the projector, the following e-mail is sent.
Subject: EPSON Projector
Line 1: The name of the projector where the problem has occurred
Line 2: The IP address set for the projector where the problem has 
occurred.
Line 3 and on: Details of the problem
The details of the problem are listed line by line. The following table 
shows the...

Reading Problem Mail Notification Function
120
The details of the problem are listed line by line. The following table 
shows the details that are given in the message for each item. To deal with 
problems/warnings, see "Reading the Indicators" sp.81
A (+) or (-) appears at the start of the message.
(+): A projector problem has occurred
(-): A projector problem has been dealt with
Message
Cause
Auto Iris Error Auto Iris Error
Cinema filter error Cinema filter error
Cinema Filter Warning Cinema...