Epson Powerlite 765c Multimedia Projector Users Guide

							Presenting Through a Wireless Network51
Once the card is inserted, you see one of these screens, depending 
on the currently selected mode:
4. If you’ve already set up your computer and projector for the mode 
you want to use—Ad Hoc mode (also called computer-to-
computer mode) or Access Point mode (also called infrastructure 
mode)—skip to “Projecting Wirelessly” on page 74. 
Otherwise, continue with the next section. 
note
If you see a message asking 
you to insert a LAN or 
memory card, check to make 
sure your 802.11G/B card is 
properly inserted.
Ad Hoc mode
Access Point mode 
						

							52Presenting Through a Wireless Network
Configuring the Connection
You can use NS Connection to connect to the projector and send 
images wirelessly in two modes: Ad Hoc mode or Access Point mode. 
■Ad Hoc mode (computer-to-computer mode) lets you connect 
just one computer to the projector at a time; it’s easy to set up, 
and the only equipment you need is a computer with a wireless 
(802.11g or 802.11b) network card or adapter, or a Macintosh 
with an AirPort
® or AirPort Extreme card. 
■Access Point mode (infrastructure mode) lets multiple computers 
access the projector at the same time and easily trade off control 
over the projector. To use Access Point mode, you need a wireless 
(802.11g or 802.11b) access point or an AirPort Extreme (or 
AirPort) base station, and one or more computers with wireless 
network cards or adapters. 
Follow the instructions below for the mode you want to use. 
Using Ad Hoc Mode 
To use Ad Hoc (computer-to-computer) mode, adjust your projector 
and wireless card or adapter settings as described in this section. 
Configuring the Projector
1. Switch the projector to EasyMP mode and insert the Epson 
802.11G/B card (see page 50). You see this screen:
note
Make sure you’ve installed 
the NS Connection software 
as described on page 169.
To connect to the projector 
o v e r  a  w i r e l e s s  n e t w o r k ,  y o u r  
computer must be running 
Windows 98, Me, 2000, or 
XP. Your Macintosh must 
be running OS X 10.2.4 or 
later. See page 169 for 
complete system 
requirements for projecting 
wirelessly.
Access Point mode 
(infrastructure mode) is 
required to achieve transfer 
s p e e d s  u p  t o  5 4 M B / s e c  o n  a n  
802.11g network. Ad Hoc 
mode (computer-to-
computer mode) limits 
network connections to 
11MB/sec. This is a 
standard specification of 
802.11g networking. 
Config button 
						

							Presenting Through a Wireless Network53
2. To select Config, press the Enter button on the remote control.
3. Highlight 
Basic under Wireless LAN and press Enter.
You see the following screen:
Make sure 
Easy connect mode is selected, as shown above. 
If not, use the  pointer button on the remote control to 
highlight the checkbox next to 
Easy connect mode, then press 
Enter to select it. 
4. Make sure the projector has a unique name, so you can identify it 
when connecting to it from your computer. 
If you need to rename it, highlight the 
Projector name text box 
then press 
Enter. The text box turns yellow to indicate you are in 
input mode. 
Press the  pointer button up to select individual letters in 
alphabetical order, or down to select letters in reverse order; then 
press the  pointer button to the right to move to the next 
Easy connect 
mode
note
If you want to enter a blank 
space, use the space character 
that comes before the capital 
letter A.
If you want to enter 
numbers, use the numeric 
keypad while holding down 
the 
Num button on the 
remote control.  
						

							54Presenting Through a Wireless Networkcharacter position. When you’re done typing the new name, press 
Enter.
5. If your network card supports an SSID or ESSID name (see 
page 57), highlight the 
ESSID text box, press Enter, and enter the 
name of your ad hoc network. When you’re done, press 
Enter. 
Note that the ESSID is case-sensitive (if you enter the name in 
uppercase on the projector, you must type it the same way on the 
computer connecting to the projector). 
6. If you want to create a password for remote access to the 
projector, highlight the 
Password for WEB control checkbox, 
press 
Enter, and enter a password of up to 8 alphanumeric 
characters. When you’re done, press 
Enter.
7. If you want to set up a security keyword so that only people who 
are in the same room as the projector can access it, turn 
Projector 
keyword
 on. Then when you want to connect to the projector, it 
displays a randomized four-digit number or “keyword” on the 
screen. When prompted by NS Connection, you can enter the 
keyword on your computer to connect (see page 77). 
8. When you’re done making these settings, highlight the 
OK button 
at the top of the screen (you can either press the   button on the 
remote control or use the  pointer button to highlight it), then 
press 
Enter. Highlight the OK button again and press Enter to 
return to the main EasyMP Network Screen. 
Now you’re ready to set up your computer for wireless projecting. 
Go to “Configuring the Network Settings for Windows” below, or 
“Setting Up Your Macintosh for Ad Hoc Mode” on page 57.
note
The projector keyword 
changes each time you turn 
the projector off and then on 
again, or remove and 
reinsert the 802.11g card. 
Check the keyword on the 
EasyMP Network screen 
whenever you start EasyMP 
and enter that keyword on 
your computer. You can’t 
connect using a previous 
keyword.
It is recommended that the 
keyword setting is changed 
periodically.  
						

							Presenting Through a Wireless Network55
Configuring the Network Settings for Windows
Before connecting to the projector, you need to make sure the settings 
for your notebook’s or PC’s network card match the settings you 
entered for the projector. 
1. Access your wireless network Properties window. For example, in 
Windows XP you would click 
Start > Control Panel > Network 
and Internet Connections
. Then click the Network 
Connections
 icon. You see a screen similar to this:
note
On some Windows systems, 
you can right-click 
My Network Places or 
Network Neighborhood 
on the desktop and select 
Properties.
Settings may vary, 
depending on your wireless 
network adapter. See the 
documentation for your 
adapter for more 
information. 
Right-click and select Properties 
						

							56Presenting Through a Wireless Network2. Right-click the 
Wireless Network Connection icon and select 
Properties. You see a screen similar to this:
3. Click the 
Configure button.
4. Click the 
Advanced tab. You see a screen similar to this:
Click here 
						

							Presenting Through a Wireless Network57
5. Check your wireless card’s or adapter’s device settings. 
(Depending on the type of card or adapter you’re using, some of 
the settings may be different than those listed here.)
■Set the Network Type to 802.11 Ad Hoc.
■Set the SSID to match the name you assigned to the 
projector’s ESSID. 
■Make sure Encryption is Disabled. 
6. Click the 
General tab and make sure that your wireless card or 
adapter is enabled. 
7. When you’re done, click 
OK to close the Properties dialog box. 
Now you’re ready to connect to the projector. See “Projecting 
Wirelessly” on page 74. 
Setting Up Your Macintosh for Ad Hoc Mode
Your AirPort software is automatically configured to allow your 
Macintosh to detect both computer-to-computer (Ad Hoc) and 
Access Point networks. 
Typically, you only need to select your projector’s ESSID from the 
AirPort status menu on the Macintosh menu bar. If you’re having 
problems detecting the projector, follow these steps:
1. From the Apple pull-down menu, select 
System Preferences. 
2. Double-click the 
Network icon. You see the Network settings 
window. 
						

							58Presenting Through a Wireless Network3. Make sure Location is set to 
Automatic.
4. Select 
Network Port Configurations in the Show pull-down 
menu.
5. Under Port Configurations, select 
AirPort.
6. Click 
Apply Now. Then close the window.
7. Click the AirPort icon on the menu bar at the top of the 
Macintosh desktop. You see the AirPort status menu:
8. Check to make sure AirPort is turned on.
9. Select your projector’s ESSID.
note:
If you don’t need the other 
network port 
configurations, disable 
them by deselecting their 
checkboxes. If more than 
one network port is 
enabled, the projector 
software warns you to 
turn off AirPort when you 
first connect the projector. 
Disregard this message.
Select 
Automatic 
Select Network Port 
Configurations 
then select AirPort
Choose the ESSID 
you assigned to the 
projector 
						

							Presenting Through a Wireless Network59
Using Access Point Mode 
To use Access Point (infrastructure) mode, first adjust your projector 
and wireless access point or AirPort base station settings as described 
in this section. 
Configuring the Projector
1. Switch the projector to EasyMP and insert the Epson 802.11G/B 
card (see page 50). You see this screen:
2. To select 
Config, press the Enter button on the remote control.
3. Highlight 
Basic under Wireless LAN and press Enter. 
You see the following screen:
Access point 
mode 
						

							60Presenting Through a Wireless NetworkMake sure 
Access point mode is selected, as shown above. If 
not, use the  pointer button on the remote control to highlight 
the checkbox next to 
Access point mode, then press Enter 
to select it. 
4. Make sure the projector has a unique name so you can identify it 
when connecting to it from your computer. 
If you need to rename it, highlight the Projector Name text box 
and press 
Enter. The text box turns yellow to indicate you are in 
input mode. Press the  pointer button up to select individual 
letters in alphabetical order, or down to select letters in reverse 
order; then press the  pointer button to the right to move to 
the next character position. When you’re done typing the new 
name, press 
Enter.
5. To enable your computer to find the projector on the network, 
you need to enter an ESSID, which is the SSID name of your 
access point or the name of your AirPort network. (The name of 
your AirPort network may be different from that of your AirPort 
base station; select your base station in the AirPort Admin utility 
and click 
Configure to check the name of your network.) 
Highlight the 
ESSID text box, press Enter, and enter a name. 
When you’re done, press 
Enter. Note that the ESSID is 
case-sensitive (if you enter the name in uppercase on the 
projector, you must type it the same way on the computer 
connecting to the projector). 
6. If you want to create a password for remote access to the 
projector, highlight the 
Password for WEB control text box and 
press 
Enter, and enter a password of up to 8 alphanumeric 
characters. When you’re done, press 
Enter. 
7. If you want to set up a security keyword so that only people who 
are in the same room as the projector can access it, turn 
Projector 
keyword
 on. Then when you want to connect to the projector, it 
displays a randomized four-digit number or “keyword” on the 
screen. When prompted by NS Connection, you can enter the 
keyword on your computer to connect (see page 77). 
note
If you want to enter a blank 
space, use the space character 
that comes before the capital 
letter A.
If you want to enter 
numbers, use the numeric 
keypad while holding down 
the 
Num button on the 
remote control. Press the 
Num button again to exit 
numeric keypad mode.
note
The projector keyword 
changes each time you turn 
the projector off and then on 
again, or remove and 
reinsert the 802.11g card. 
Check the keyword on the 
EasyMP Network screen 
whenever you start EasyMP, 
and enter that keyword on 
your computer. You can’t 
connect using a previous 
keyword.