Epson Powerlite 6110i Multimedia Projector Users Guide

							Projector Installation111
Installing the Rear Cable Cover and 
Lock
If you’re mounting the projector on the ceiling, you can install the 
rear cable cover to enhance the cosmetic appearance of the system.
To install the cover, insert the cover’s tabs into the slots as shown, 
then attach it with the two included screws.
For security purposes, you can also install a lock to ensure that the 
cable cover is not removed. 
						

							112Projector Installation 
						

							113
B
Technical Specifications
General
Type of display Poly-silicon TFT active matrix
Size of LCD panels Diagonal: 0.8 inch
Resolution
(native format) 1024 × 768 pixels (XGA)
Color reproduction 24 bit, 16.7 million colors
Brightness 3500 lumens (high brightness mode)
2700 lumens (low brightness mode)
Contrast ratio 600:1
Image size 30 to 300 inches
Projection distance 2.7 to 48.2 feet (0.83 to 14.69 meters)
Projection methods Front, rear, upside-down (ceiling mount)
Internal sound system 5 W monaural
Optical aspect ratio 4:3 (horizontal:vertical)
Zoom ratio 1 to 1.6
Noise level 39 dB standard filter; 43dB smoke filter
Keystone correction
± 30° (vertical) 
						

							114Technical Specifications
Projection Lamp
Type UHE (Ultra High Efficiency)
Power consumption 230 W
Lamp life Up to 4000 hours
Part number V13H010L45
Remote Control
Range 19.7 feet (6 meters)
Batteries (2) Alkaline size AAA 
Dimensions
Height 5.75 inches (146 mm) [not including feet]
Width 18.3 inches (465 mm)
Depth 13.39 inches (340 mm)
Weight 15.4 lb (7 kg) [without cable cover]
Electrical
Rated frequency 50/60 Hz AC
Power supply 100 to 120 VAC, 3.8 A
200 to 240 VAC, 1.7 A
Power consumption Operating: 331 W
Standby: 0.4 W with Network Off
10.4 W with Network On
note
Turn off this product when 
not in use to prolong the life 
of the projector.
Lamp life results will vary 
depending upon mode 
selected, environmental 
conditions and usage.  
						

							Technical Specifications115
Environmental
Temperature Operating: 32 to 104 °F (0 to 40 °C)
Storage: 14 to 140 °F (–10 to 60 °C)
Humidity Operating: 20 to 80% RH,
non-condensing
Storage: 10 to 90% RH,
non-condensing
Operating altitude 0 to 10,000 ft (0 to 3,048 m)
Safety
United States FCC Part 15B Class B
UL60950-1
Canada ICES-003 Class B
CSA C22.2 No. 60950-1
Pixelworks
™ DNX™ ICs are used in this 
projector. 
						

							116Technical Specifications
Compatible Video Formats
The projector supports NTSC, PAL, and SECAM international video 
standards, as well as the monitor display formats listed below.
To project images output from a computer, the computer’s video card 
must be set at a refresh rate (vertical frequency) that’s compatible with 
the projector; see the following table for compatible formats. As 
noted  below, some images are automatically resized to display in 
the projector’s “native” format (XGA). In addition, the frequencies 
of some computers may not allow images to display correctly; see 
your computer’s documentation for details.
Mode Refresh Rate (Hz) Resolution
VGAEGA 70 640 × 350
*
VGA—60
VGA—72
VGA—75
VGA—8560
72
75
85640 × 480*
640 × 480*
640 × 480*
640 × 480*
SVGA—56
SVGA—60
SVGA—72
SVGA—75
SVGA—8556
60
72
75
85800 × 600*
800 × 600*
800 × 600*
800 × 600*
800 × 600*
XGA—60
XGA—70
XGA—75
XGA—8560
70
75
851024 × 768
1024 × 768
1024 × 768
1024 × 768
SXGA1—70
SXGA1—75
SXGA1—8570
75
851152 × 864
*
1152 × 864*
1152 × 864*
SXGA2—60
SXGA2—75
SXGA2—8560
75
851280 × 960*
1280 × 960*
1280 × 960*
SXGA3—60
SXGA3—75
SXGA3—8560
75
851280 × 1024*
1280 × 1024*
1280 × 1024*
UXGA—60 60 1600 ×1200* 
						

							Technical Specifications117
*The image is resized using Epson’s SizeWise™ Technology. 
MAC13
MAC16
MAC19
MAC19
MAC2167
75
75
60
75640 × 480*
832 × 624*
1024 × 768
1024 × 768
1152 × 870
*
NTSC 
PAL
SECAM60
50
50—
—
—
SDTV (480i)
SDTV (576i)
SDTV (480p)
SDTV (576p)
HDTV (720p)
HDTV (1125i)60
50
60
50
50/60
50/60720 × 480
*
720 × 576*
720 × 480*
720 × 576*
1280 × 720*
1920 × 1080*
Mode Refresh Rate (Hz) Resolution 
						

							118Technical Specifications 
						

							119
C
Notices
This appendix includes safety instructions and other important information 
about your PowerLite projector.
Important Safety Instructions
Follow these safety instructions when setting up and using the projector:
■Do not place the projector on an unstable cart, stand, or table.
■Do not use the projector near water or sources of heat.
■Use the type of power source indicated on the projector. If you are not 
sure of the power available, consult your dealer or power company.
■Place the projector near a wall outlet where the plug can be easily 
unplugged.
■Insert the projector’s three-wire grounding-type plug into a properly 
grounded outlet. If you have a two-prong outlet, contact an electrician 
to replace it. Do not hold the plug with wet hands.
■Take the following precautions for the plug. Failure to comply with 
these precautions could result in sparks or fire: Do not insert the plug 
into an outlet with dust present. Insert the plug firmly into the outlet.
■Do not overload wall outlets, extension cords, or integral convenience 
receptacles. This can cause fire or electric shock.
■Do not place the projector where the cord can be walked on. This may 
result in fraying or damage to the plug.
■Unplug the projector from the wall outlet before cleaning. Use a damp 
cloth for cleaning. Do not use liquid or aerosol cleaners.
■Do not block the slots and openings in the projector case. They provide 
ventilation and prevent the projector from overheating. Do not operate 
the projector on a sofa, rug, or other soft surface, or in a closed-in 
cabinet unless proper ventilation is provided.
■Never push objects of any kind through the cabinet slots. Never spill 
liquid of any kind into the projector. 
						

							120Notices
■Except as specifically explained in this User’s Guide, do not attempt to 
service this product yourself. Refer all servicing to qualified personnel. 
Opening or removing covers may expose you to dangerous voltages and 
other hazards.
■Unplug the projector from the wall outlet and refer servicing to qualified 
service personnel under the following conditions: When the power cord 
or plug is damaged or frayed. If liquid has been spilled into the 
projector, or if it has been exposed to rain or water. If it does not operate 
normally when you follow the operating instructions, or if it exhibits a 
distinct change in performance, indicating a need for service. If it has 
been dropped or the housing has been damaged.
■The lamp(s) in this product contain mercury. Please consult your 
state and local regulations regarding disposal or recycling. Do not put in 
the trash.
■Unplug the projector during lightning storms or when it will not be used 
for extended periods.
■Do not place the projector and/or remote control on top of 
heat-producing equipment or in a hot location.
■If you use the projector in a country other than where you purchased it, 
use the correct power cord for that country.
■Do not stand on the projector or place heavy objects on it.
■Do not use the projector outside of the required temperature range of 41 
to 104 °F (5 to 40 °C). Doing so may cause an unstable display and 
could lead to projector damage.
■Do not store the projector outside of the required temperature range of 
14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of 
time. Doing so may cause damage to the case.
WARNING: The cords included with this product contain chemicals, 
including lead, known to the State of California to cause birth defects or 
other reproductive harm. Wash hands after handling. (provided in accordance 
with Proposition 65 in Cal. Health & Safety Code § 25249.5 et seq)