Epson EPL N3000T User Manual

108Using the PostScript Printer Software (Windows) If your document has overlapping text and graphics, select 
Substitute with Device Font. Using downloaded TrueType fonts 
to print when text and graphics overlap may cause output errors.
Document Options
Page Layout (N-up) Option
Specify how many pages of your document to print on one sheet 
of paper. The options are Normal (one-up), Two-up (1x2), Four-up 
(2x2), Six-up (2x3), Nine-up (3x3), and Sixteen-up (4x4).
PostScript Options
PostScript Output...

Using the PostScript Printer Software (Windows)109
4
4
4
4
4
4
4
4
4
4
4
4
Printer Features
RITech
Select whether to use RITech when printing. RITech improves the 
appearance of printed lines, text, and graphics. The options are 
On and Off.
Toner Save Mode
Select whether to use the Toner Save Mode when printing. When 
the Toner Save Mode is turned on, the printer uses about 50% less 
toner than normal. The options are On and Off.
Printer driver settings
Printer settings specific to your printer are...

110Using the PostScript Printer Software (Windows) Form To Tray Assignment
Assign the desired paper size to the various available paper 
sources. Once this setting is specified, the printer will 
automatically feed paper from the paper source that holds the 
selected paper size.
The paper source options are MP Tray, Cassette 1, Cassette 2, 
Cassette 3, Manual Feed 1st Page, and Manual Feed EachPage. 
However, the actual paper sources that are available will differ 
according to the printer and the...

Using the PostScript Printer Software (Windows)111
4
4
4
4
4
4
4
4
4
4
4
4
If you select TBCP (Tagged Binary Communications Protocol), all 
data except for special control characters is sent in binary (8-bit) 
format. The binary formats can be sent over parallel or serial 
communications ports and are faster than sending data in the 
ASCII format.
Send CTRL-D Before Each Job
Specify whether a CTRL+D character should be sent at the 
beginning of every PostScript document. CTRL+D at the 
beginning-of-file...

112Using the PostScript Printer Software (Windows) Minimum Font Size to Download as Outline
Specify the minimum font size (in pixels) for which the printer 
driver will download TrueType fonts as outline (Type 1) fonts. A 
font smaller than the minimum setting will be downloaded as a 
bitmap (Type 3/Type 32) font.
Maximum Font Size to Download as Bitmap
Specify the maximum font size (in pixels) for which the printer 
driver will download TrueType fonts as bitmap (Type 3/Type 32) 
fonts. A font larger...

Using the PostScript Printer Software (Windows)113
4
4
4
4
4
4
4
4
4
4
4
4
Note:
If your computer is running Windows XP, click Start and then click 
Printers and Faxes.
3. Double-click the Add Printer icon.
Note:
If your computer is running Windows XP, click Add a printer 
under Printer Tasks.
4. The Add Printer Wizard will be displayed. Follow the
on-screen instructions until the screen asking you to select the 
printer model is displayed.
5. Click Have Disk and specify the path to the appropriate INF...

114Using the PostScript Printer Software (Windows) 4. After the USB printer driver installation is done, the Add 
Printer Wizard will launch automatically. Follow the 
on-screen instructions to continue with the installation until 
the screen asking you to select the printer model is displayed. 
5. Click Have Disk and specify the path to the appropriate INF 
file necessary for installation. If your CD-ROM drive is D:, the 
path will be D:\ADOBEPS\ENGLISH\WIN2K-XP\PS_SETUP 
(change the drive letter as...

Using the PostScript Printer Software (Windows)115
4
4
4
4
4
4
4
4
4
4
4
4
Note:
If your computer is running Windows XP, click A network printer, 
or a printer attached to another computer.
6. Click Next to browse for and select the printer on the network.
7. Click OK when the following message appears:
“The server on which the XXX printer resides does not have 
the correct printer driver installed.”
8. When the screen asking you to select the printer model is 
displayed, click Have Disk and specify the...

116Using the PostScript Printer Software (Windows)
Printer driver settings
Printer settings specific to your printer are available through the 
Device Settings tab of the printer’s Properties dialog box. In 
addition to the settings there, click the Printing Preferences 
button on the General sheet or the Printing Defaults b u t t o n  o n  t h e  
Advanced sheet for more print settings. The basic print settings 
are grouped under the Layout and Paper/Quality tabs, while more 
advanced settings are...

Using the PostScript Printer Software (Windows)117
4
4
4
4
4
4
4
4
4
4
4
4
Available PostScript Memory
Specify the amount of available PostScript memory. The available 
PostScript memory is a subset of the printer’s total physical 
memory. It is recommended that you use the default setting.
Output Protocol
Specify the protocol that the printer will use for print jobs. The 
options are ASCII, TBCP, and Binary.
TBCP cannot be used with AppleTalk.
Binary can be used only when using AppleTalk.
If ASCII is...