Epson Aculaser CX28DN User Manual

Loading Media 109
5Slide the media guides against 
the edges of the paper.
6Close Tray 2.
7Select PAPER SETUP/TRAY2 PAPER in the UTILITY menu, and 
then select the settings for the size of paper that is loaded. See also 
“Specifications” on page 90.
 

Loading Media 110
Tray 3 (Optional Lower Feeder Unit)
Only plain paper can be loaded in Tray 3.
Loading Plain Paper
1Pull out Tray 3.
2Press down the media pressure 
plate to lock it into place.
3Slide the media guides to pro-
vide more space between them.
 

Loading Media 111
4Load the paper face up in the 
tray.
Do not load above the  
mark. Up to 500 sheets 
(80 g/m2 [22 lb]) of plain 
paper can be loaded into 
the tray at one time.
5Slide the media guides against 
the edges of the paper.
 

Loading Media 112
6Close Tray 3.
 

About Duplex Printing 113
About Duplex Printing
Duplex (double-sided) printing can be done with this printer, which has the 
duplex unit built in as a standard. If the paper has low opacity (high translu-
cency), then the printed data from one side of the page will show through to 
the other side. Check your application for margin information. For best 
results, print a small quantity to make sure the opacity is acceptable.
Note
Only plain paper, 60–90 g/m2 (16–24 lb bond) can be autoduplexed. See...

About Duplex Printing 114
In addition, if “Combination” has been set to “Booklet”, autoduplex printing is 
performed.
The following Order settings are available when “Booklet” is selected.
1Load plain paper into the tray.
2From the printer driver, specify duplex (double-sided) printing (Layout tab 
in Windows).
3Click OK.
With autoduplexing, the back side is printed first, and then the front 
side is printed.If “Left Binding” is selected, the pages can be folded as a 
left-bound booklet.
If “Right...

Output Tray 115
Output Tray
All media is fed out facing down into the output tray on the left side of the 
machine. This tray has a capacity of approximately 250 sheets (A4/Letter) of 
80 g/m
2 paper.
If the media is stacked too high in the output tray, your machine may 
experience media misfeeds, excessive media curl, or static buildup. 
Remove transparencies as soon as possible from the output tray to 
avoid static buildup
The output tray can be pulled out to 
be extended. Adjust the output tray...

Media Storage 116
Media Storage
„Keep media on a flat, level surface in its original wrapper until it is time to
load it.
Media that has been stored for a long time out of its packaging may dry up 
too much and cause misfeeding.
„If media has been removed from its wrapper, place it in its original pack-
aging and store in a cool, dark place on a level surface.
„Avoid moisture, excessive humidity, direct sunlight, excessive heat (above 
35°C [95°F]), and dust 
„Avoid leaning against other objects or...

Original Media 117
Original Media
Specifications
Documents that can be placed on the original glass
The following types of documents can be placed on the original glass.
Observe the following precautions when placing a document on the original 
glass.
„Do not place objects weighing more than 3 kg (6.6 lb) on the original 
glass; otherwise the glass may be damaged.
„Do not press down extremely hard on a book spread on the original glass; 
otherwise the original glass may be damaged.
Documents that can be...

Original Media 118
„Documents with pages that have had cutouts removed or are cutouts
„Label sheets
„Offset printing masters
„Documents with binder holes