Epson Aculaser CX16 User Manual

8. When installing Tray 2 without installing the duplex option, also install the locking pins (one in
each opening on the left and right sides at the back of Tray 2).
While holding the grip of the locking pin vertical, insert the locking pin into the opening on either
the left or right side of the 500-sheet paper cassette unit and, while pushing it in, turn it to either the
left or the right. The locking pin is installed when its grip is horizontal.
Installing the left and right locking pins secures the...

Kit Contents
Duplex option
Attachment
Note:
If Tray 2 is installed, it is not necessary to install the attachment. In this case, skip “Installing the
Attachment”, and continue with “Installing the Duplex option” on page 203.
Installing Attachment
If the attachment is installed, the duplex option can be installed.
(The attachment cannot be used by itself; it must be used together with the duplex option.)
Note:
Since consumables are installed in the machine, be sure to keep the machine level when moving it...

3. Prepare the attachment.
Note:
Be sure to place the attachment on a level surface.
4. Lift the machine and place it on top of the attachment, making sure that the positioning pins on the
attachment correctly fit into the holes on the bottom of the machine.
w
Warning:
This machine weighs approximately 21 kg (46 lb) when it is fully loaded with consumables.
5. Open Tray 1 and reattach the dust cover.
Next, install the duplex option.
Installing the Duplex option
Note:
The illustrations in the following...

2. Remove the tape affixed to the rear cover.
3. If the locking pins are installed on the left and right side at the back of Tray 2, remove them. 
To remove a locking pin, turn it to either the left or the right so that its grip is vertical, and then pull
out the locking pin to remove it.
4. Prepare the duplex option.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Installing Accessories (AcuLaser CX16NF only)     204
 

5. Install the duplex option.
Align the duplex option with its installation position, and then push down on the bottom of the
duplex option until it locks into place.
Note:
When attaching the duplex option, attach the bottom of the option first. If the duplex option is
attached incorrectly, it may be damaged.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Installing Accessories (AcuLaser CX16NF only)     205
 

6. Open the duplex cover.
While holding the duplex option against the machine, tighten the screws inside the cover to
complete the installation of the duplex option.
7. Reconnect all interface cables.
8. Reconnect the power cord, and turn on the machine.
Note:
Once you install the duplex option unit, do not use the printer without it. The gears at the openings of the
printer may pinch your finger or catch your hair. Always attach the protective seal applied with the
duplex option unit when you use the...

Appendix A
Appendix
Technical Specifications
Model name AcuLaser CX16NF L622B
AcuLaser CX16 L622A
Type Desktop (Full color laser beam printer-based all-in-one)
Document holder Stationary
Developing system Mono component development system
Fusing system Heat roller system
Resolution
1200 dpi × 600 dpi or
600 dpi × 600 dpi
First print Simplex
❏Monochrome
14 seconds for A4/Letter (plain paper)
❏Full color
23 seconds for A4/Letter (plain paper)
First copy Simplex
❏Monochrome
23 seconds for A4/Letter (plain...

Media sizes Tray 1 (Multipurpose tray)
❏Paper width: 92 to 216 mm (3.6" to 8.5")
❏Paper length:
Plain paper:
195 to 356 mm (7.7" to 14.0")
Thick stock 1/2:
184 to 297 mm (7.25" to 11.7")
Tray 2 (optional) (AcuLaser CX16NF only)
❏A4
Paper/Media Plain paper (60 to 90 g/m2)
Letterhead
Envelopes
Labels
Thick stock 1 (91 to 163 g/m2)
Thick stock 2 (164 to 209 g/m2)
Postcard
Input capacity Tray 1 (multipurpose tray)
❏Plain/recycled paper: 200 sheets
❏Envelopes: 10 envelopes
❏Letterhead,...

Acoustic noise AcuLaser CX16NF Standby: 38 dB or less
Printing: 49 dB or less
Copying: 52 dB or less
AcuLaser CX16 Standby: 38 dB or less
Printing: 50 dB or less
Copying: 50 dB or less
External dimensions AcuLaser CX16NF Height: 432 mm (17.0")
Width: 405 mm (15.9")
Depth: 427 mm (16.8")
AcuLaser CX16 Height: 375 mm (14.8")
Width: 405 mm (15.9")
Depth: 427 mm (16.8")
Weight AcuLaser CX16NF 17.6 kg (without consumables)
20.8 kg (with consumables)
AcuLaser CX16 16.0 kg (without...

R&TTE directive 1999/5/EC 
(AcuLaser CX16NF only)ES203021-1
ES203021-2
ES203021-3
ES201187
EG201120
EN60950-1
❏For European users (AcuLaser CX16NF only):
We, Seiko Epson Corporation, hereby declare that the equipment Model, L622B, is in compliance
with the essential requirements and other relevant provisions of Directive 1999/5/EC.
❏For use only in (AcuLaser CX16NF only):
Ireland, UK, Austria, Germany, Liechtenstein, Switzerland, France, Belgium, Luxemburg,
Netherlands, Italy, Portugal, Spain, Denmark,...