Epson AcuLaser C9100 User Manual

Installing Options211
6
6
6
6
6
6
6
6
6
6
6
6
6. Plug the connection cable into both the socket on the HDD 
and that on the board as shown below.
7. Reattach the cover to the right side of the printer by inserting 
the three projections at the bottom of the cover to the notches 
on the printer, and then sliding the cover forward to firmly fit 
it to the printer. Make sure the projection at the top of the 
cover is inserted to the notch on the printer.
8. Secure the cover with the three screws.
 

212Installing Options 9. Reconnect the power cord and turn the printer on.
To confirm that the Hard Disk Drive is installed correctly, prints 
a status sheet. See “Printing a Status Sheet” on page 276. If the 
drive is not listed on the status sheet, try reinstalling the drive. 
Make sure that the connector on the Hard Disk Drive is securely 
connected to the socket on the circuit board.
Note for Windows users:
If you are using Windows, and EPSON Status Monitor 3 is not 
installed, you have to make...

Installing Options213
6
6
6
6
6
6
6
6
6
6
6
6
Memory Module
By installing a Dual In-line Memory Module (DIMM), you can 
increase printer memory up to 1,024 MB. You may want to add 
additional memory if you are having difficulty printing complex 
graphics.
This printer has two memory slots, but one slot has a 128 MB 
DIMM already installed in it at the time of manufacture. To 
increase printer memory more than 640 MB, remove the original 
128 MB DIMM first and then install two optional DIMMs.
Note:
The...

214Installing Options 1. Turn the printer off and unplug the power cord.
2. Remove the three screws from the cover on the right side of 
the printer.
s
 

Installing Options215
6
6
6
6
6
6
6
6
6
6
6
6
3. Slide the cover backward. Then tilt it toward you and remove 
it.
w
Warning:
When you open the right side cover, be careful not to touch 
the areas surrounding the caution label on the circuit board 
since the areas may be very hot.
4. Identify the expansion RAM slot.
* Expansion RAM slot
*
 

216Installing Options 5. Confirm that the notch on the expansion RAM module 
matches that of the socket.
6. Firmly insert the top edge of the RAM module into the socket 
until it stops.
7. Press the inserted RAM module until it clicks so that the 
whole module is fully installed.
 

Installing Options217
6
6
6
6
6
6
6
6
6
6
6
6
c
Caution:
❏Do not force the memory module into the socket.
❏Be sure to insert the memory module in the correct 
direction.
8. Reattach the cover to the right of the printer by inserting the 
three projections at the bottom of the cover to the notches on 
the printer, and then sliding the cover forward to firmly fit it 
to the printer. Make sure the projection at the top of the cover 
is inserted to the notch on the printer. 
9. Secure the cover with the...

218Installing Options To confirm that the memory module is installed correctly, print a 
status sheet. See “Printing a Status Sheet” on page 276 for 
instructions. If the total amount of memory listed does not include 
the size of the optional memory module, try reinstalling the 
module. Make sure that the module is securely seated into the 
memory slot on the circuit board.
Note for Windows users:
If you are using Windows, and EPSON Status Monitor 3 is not 
installed, you have to make settings manually...

Installing Options219
6
6
6
6
6
6
6
6
6
6
6
6
Adobe PostScript 3 Kit/P5C Emulation Kit
The Adobe PostScript 3 Kit ROM module and P5C Emulation kit 
are available as an option for this printer. These modules allow 
your printer to print documents in the PostScript printing 
language and in the PCL5c printing language.
Note:
The features provided by the Adobe PostScript 3 ROM Module cannot 
be used when the printer is connected to a Macintosh computer using 
an optional IEEE 1394 Type B Interface Card....

220Installing Options 1. Turn the printer off and unplug the power cord.
2. Remove the three screws from the cover on the right side of 
the printer.
s