Epson AcuLaser C2600N User Manual

Using the Control Panel271
7
7
7
7
7
7
7
7
7
7
7
7
The installed toner cartridge is not a genuine Epson toner 
cartridge. Using a non-genuine toner cartridge may affect print 
quality. Epson shall not be liable for any damages or problems 
arising from the use of consumable products not manufactured 
or approved by Epson. Installing a genuine toner cartridge is 
recommended. Press the NStart/Stop button on the control panel 
to resume printing.
Offline
The printer is not ready to print. Press the...

272Using the Control Panel Paper Out tttt sssss
There is no paper in the specified paper source (tttt). Load paper 
of the size (sssss) into the paper source.
Paper Set tttt sssss
The paper loaded in the specified paper source (tttt) does not 
match the required paper size (sssss). Replace the loaded paper 
with the correct size paper and press the NStart/Stop button to 
resume printing, or press the +Cancel Job button to cancel the 
print job.
If you press the NStart/Stop button without replacing the...

Using the Control Panel273
7
7
7
7
7
7
7
7
7
7
7
7
Print Overrun
The required time to process the print data exceeded the print 
engine speed because the current page is too complex. Press the 
NStart/Stop button to resume printing, or press the +Cancel 
Job button to cancel the print job. If this message appears again, 
select On as the Page Protect setting in the control panel’s Setup 
Menu or select Avoid Page Error on the printer driver.
If you continue to receive this message when printing a...

274Using the Control Panel This message appears when the printer switches to the B/W 
mode. See  Switching the Printing Mode on page 283 to find how 
to switch the mode.
Replace Fuser
The fuser has reached the end of its service life. Turn the printer 
off, then replace the fuser unit with a new one. See  Fuser Unit 
on page 326 for instructions.
Replace Photoconductor
The photoconductor has reached the end of its service life. Turn 
off the printer, then replace the photoconductor unit with a new 
one....

Using the Control Panel275
7
7
7
7
7
7
7
7
7
7
7
7
Reserve JobCanceled
The printer cannot store the data of your print job using the 
Reserve Job function. The maximum number of print jobs stored 
on the printer’s Hard Disk Drive has been reached, or the drive 
has no more memory available to store a new job. To store a new 
print job, delete a previously stored job. Also, if you have any 
Confidential Jobs stored, printing those jobs will make more 
memory available. 
To clear this error, select Clear...

276Using the Control Panel The printer is currently performing a self test and initialization.
Service Req Cffff/Service Req Eggg
A controller error or a print engine error has been detected. Turn 
off the printer. Wait at least 5 seconds, then turn it back on. If the 
error message still appears, write down the error number listed 
on the LCD panel (Cffff/Eggg), turn off the printer, unplug the 
power cord, then contact a qualified service representative.
Sleep
The printer is currently in the power-save...

Using the Control Panel277
7
7
7
7
7
7
7
7
7
7
7
7
uuuu Toner Low
This message indicates that the toner cartridge for the indicated 
color is near the end of its service life. Prepare a new toner 
cartridge.
Warming Up
The printer is warming up the fuser to be ready to print.
Waste Toner Box Near Full
The waste toner collector is near full of toner.
Worn Fuser
This message indicates that the fuser unit is near the end of its 
service life. Printing after this message appears is not guaranteed. 
Turn the...

278Using the Control Panel To clear this warning message and continue printing, select Clear 
All Warning from the control panel’s Reset Menu. For instruction 
about accessing the control panel menus, see  How to access the 
control panel menus on page 223.
Write Error ROM P
The printer is unable to write data into the ROM module correctly. 
You cannot remove the ROM P because the ROM P is a program 
ROM module. Contact your dealer.
Writing ROM A/Writing ROM P
This message indicates that a ROM module in...

Using the Control Panel279
7
7
7
7
7
7
7
7
7
7
7
7
3. Use the dDown or uUp button to scroll to the appropriate 
user name, then press the Enter button.
4. Use the dDown or uUp button to scroll to the appropriate 
job name, then press the Enter button.
5. To specify the number of copies you want to print, press the 
Enter button, then use the dDown and uUp buttons to 
select the number of copies.
To delete the print job without printing any copies, press the 
dDown button to display Delete on the LCD...

280Using the Control Panel 4. Enter your four-digit password by using the corresponding 
buttons, as shown below.
Note:
❏Passwords are always four digits.
❏Passwords consist of numbers from 1 through 4.
❏If no print jobs have been saved with the password you entered, 
Password Error appears briefly on the LCD panel then the 
printer exits the control panel menus. Confirm the password 
and try again.
5. Use the dDown or uUp button to scroll to the appropriate 
job name, then press the Enter button.
6. To...