Epson AcuLaser C1100D User Manual

Maintenance and Transportation161
7
7
7
7
7
7
7
7
7
7
7
7
Toner Cartridge
Handling precautions
Always observe the following handling precautions when 
replacing the consumable products:
❏Installing a genuine toner cartridge is recommended. Using a 
non-genuine toner cartridge may affect print quality. Epson 
shall not be liable for any damages or problems arising from 
the use of consumable products not manufactured or 
approved by Epson.
❏When handling toner cartridge, always place them on a clean...

162Maintenance and Transportation
Replacing a toner cartridge
Follow the steps below to replace a toner cartridge.
1. Turn the printer on.
2. Open cover A.
3. Push up the right lever to unlock the toner cartridge.
 

Maintenance and Transportation163
7
7
7
7
7
7
7
7
7
7
7
7
4. Remove the toner cartridge from the printer.
5. Take the new toner cartridge out of its package and gently 
shake the toner cartridge as shown below.
6. Hold the tag and gently pull the toner seal upward and 
remove it.
 

164Maintenance and Transportation 7. Insert the cartridge all the way until it stops securely with the 
arrow mark on the top of the toner cartridge facing toward 
cover A.
8. Push down the right lever to lock the toner cartridge.
Note:
The toner cartridge is installed securely when the right lever cannot 
be turned any further. Make sure that the toner cartridge is installed 
securely.
9. Close cover A.
 

Maintenance and Transportation165
7
7
7
7
7
7
7
7
7
7
7
7
10. Confirm the error message on the LCD panel. When an other 
toner cartridge needs to be replaced, an error message is 
displayed. Repeat steps 3 to 8 and replace the cartridge.
Photoconductor Unit
Handling precautions
Always observe the following handling precautions when 
replacing the consumable products:
❏The photoconductor unit weighs 3.0 kg (6.6 lb). Be sure to hold 
it firmly by the handle when carrying it.
❏When replacing the...

166Maintenance and Transportation
Replacing the photoconductor unit
Follow the steps below to replace the photoconductor unit.
1. Turn the printer on, and open cover B.
Note:
When installing the optional Duplex Unit, open cover D first, then 
cover B.
2. Raise the yellow lever inside cover B.
 

Maintenance and Transportation167
7
7
7
7
7
7
7
7
7
7
7
7
3. Remove the photoconductor unit.
4. Take the new photoconductor unit out of its package and 
remove the protective sheet.
c
Caution:
Do not touch the belt on the top of the unit or the blue photo 
conductor area. Otherwise, the print quality may decrease.
 

168Maintenance and Transportation 5. Hold the photoconductor unit by its handle, and insert the 
unit until it clicks shut with aligning the arrow marks on the 
printer.
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION 
HIGH TEMPERATURE. If the printer has been in use, the 
fuser may be very hot.
c
Caution:
Do not touch the parts inside the printer.
6. Push the yellow lever down, and then close cover B.
Note:
When installing the optional Duplex Unit, close cover D.
 

169
Cleaning the Printer
The printer needs only minimal cleaning. If the printer’s outer 
case is dirty or dusty, turn off the printer and clean it with a soft, 
clean cloth moistened with a mild detergent.
c
Caution:
Never use alcohol or paint thinner to clean the printer cover. 
These chemicals can damage the components and the case. Be 
careful not to get water onto the printer mechanism or any 
electrical components.
 

170
Cleaning the pickup roller
Follow the steps below to clean the pickup roller.
1. Open the MP tray, then remove the loaded paper.
2. Gently wipe the rubber parts of the pickup roller inside the 
MP tray with a wet, well-wrung cloth.
Cleaning the print head
Follow the steps below to clean the printer head.
1. Open the cleaner cover on the right side of the printer. Then, 
open cover A.