Home > Epson > Printer > Epson AcuLaser 2600DTN User Manual

Epson AcuLaser 2600DTN User Manual

Here you can view all the pages of manual Epson AcuLaser 2600DTN User Manual. The Epson manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 321

Replacing Consumable Products321
9
9
9
9
9
9
9
9
9
9
9
9
2. Remove the filter from the printer.
3. Take the new filter out of its package. Insert the new filter to 
the printer.
4. Remove the waste toner collector.
 

Page 322

322Replacing Consumable Products 5. Take the cap off and cover the hole for the waste toner 
collector with it.
Note:
If you need to set the waste toner collector down, place it on a flat 
surface with the capped side facing up to prevent the toner content 
from spilling out.
6. Turn the blue knob on the front of the photoconductor as 
shown below.
 

Page 323

Replacing Consumable Products323
9
9
9
9
9
9
9
9
9
9
9
9
7. Hold the handle of the photoconductor unit and pull it toward 
you to remove the photoconductor unit form the printer.
8. Take the new photoconductor unit out of its package and 
remove the protective cover.
c
Caution:
Do not touch the belt on the top of the unit or the green photo 
conductor area. Otherwise, the print quality may decrease.
 

Page 324

324Replacing Consumable Products 9. Hold the photoconductor unit by its handle and insert the unit 
into the printer.
10. Turn the blue knob back to the original position.
 

Page 325

Replacing Consumable Products325
9
9
9
9
9
9
9
9
9
9
9
9
11. Hold the cleaning knob [a] and move it slowly in and out a 
few times.
12. Insert the new waste toner collector into the printer.
 

Page 326

326Replacing Consumable Products 13. Close cover D.
Fuser Unit
Handling precautions
Always observe the following handling precautions when 
replacing the consumable products.
Do not touch the surface of the consumable product. Doing so 
may impair print quality.
w
Warning:
❏The fuser unit can be very hot if the printer has been in use. 
Turn the printer off and wait for 30 minutes until the 
temperature has subsided before replacing the fuser unit.
❏Do not dispose of the used consumable products in fire,...

Page 327

Replacing Consumable Products327
9
9
9
9
9
9
9
9
9
9
9
9
Replacing the fuser unit
Follow the steps below to replace the fuser unit.
1. Turn off the printer, and wait for 30 minutes until the 
temperature has subsided.
2. Push the latch on cover A to the left and open the cover.
3. Open cover B.
 

Page 328

328Replacing Consumable Products 4. Turn the handles on both side of the fuser unit to unlock them.
5. Lift the fuser unit out of the printer as shown below.
 

Page 329

Replacing Consumable Products329
9
9
9
9
9
9
9
9
9
9
9
9
6. Take the new fuser unit out of its package and remove the 
protective cover.
7. Hold the new fuser unit by the handles and lower it into the 
printer making sure that the guide posts slide into the holes 
on the bottom of the unit.
 

Page 330

330Replacing Consumable Products 8. Turn the handles on both sides of the fuser unit to lock them.
Note:
Make sure that the locks are completely in the locked position.
9. Close covers B and A.
 
Start reading Epson AcuLaser 2600DTN User Manual

Related Manuals for Epson AcuLaser 2600DTN User Manual

All Epson manuals