Epson AcuLaser 2600DTN User Manual
Here you can view all the pages of manual Epson AcuLaser 2600DTN User Manual. The Epson manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 311
Installing Options311 8 8 8 8 8 8 8 8 8 8 8 8 4. Identify the ROM module slots. Note: There are two ROM slots, and either slot can be used to attach the ROM module. 5. Insert the ROM module horizontally into the slot until the clip comes out. c Caution: ❏Do not force the ROM module into the socket. ❏Be sure to insert the ROM module in the correct direction. ❏Never remove the ROM module installed on the standard ROM socket (P).
Page 312
312Installing Options 6. Reattach the cover to the back side of the printer and secure it with the four screws. 7. Reconnect the power cord and turn the printer on. To confirm that the option is installed correctly, print a Status Sheet. See Printing a Status Sheet on page 370. If P5C is not listed as an installed emulation on the status sheet, try reinstalling the module. Make sure that it is securely seated into the ROM slot on the circuit board. Removing the P5C ROM module c Caution: Before you...
Page 313
Replacing Consumable Products313 9 9 9 9 9 9 9 9 9 9 9 9 Chapter 9 Replacing Consumable Products Replacement Messages When you see the following messages on the LCD panel or the window of EPSON Status Monitor 3, replace the appropriate consumable products. You can continue to print for a short time after a message appears, but Epson recommends early replacement to maintain print quality and extend the life of your printer. Note: To clear the warning, select Clear All Warning from the control...
Page 314
314Replacing Consumable Products * T h e l e t t e r s C , M , Y , o r K a p p e a r i n t h i s p o s i t i o n , i n d i c a t i n g t h e c o l o r o f t h e t o n e r to be replaced. For example, the message Y Toner Low means that the amount of toner remaining in the yellow toner cartridge is low. Note: Messages appear for one consumable product at a time. After replacing a consumable product, check the LCD panel for replacement messages for other consumable products. Even if...
Page 315
Replacing Consumable Products315 9 9 9 9 9 9 9 9 9 9 9 9 Toner Cartridge Handling precautions Always observe the following handling precautions when replacing the consumable products: ❏Installing a genuine toner cartridge is recommended. Using a non-genuine toner cartridge may affect print quality. Epson shall not be liable for any damages or problems arising from the use of consumable products not manufactured or approved by Epson. ❏When handling toner cartridge, always place them on a clean...
Page 316
316Replacing Consumable Products Replacing a toner cartridge Follow the steps below to replace a toner cartridge. 1. Prepare a new cartridge of the color (K, C, M or Y) displayed on the LCD panel. 2. Open cover D. 3. Hold the toner cartridge knob and tilt it toward you.
Page 317
Replacing Consumable Products317 9 9 9 9 9 9 9 9 9 9 9 9 4. Remove the empty toner cartridge from the printer. 5. Take the protective materials off of the new cartridge, and gently shake the new toner cartridge a few times. 6. Take the new toner cartridge out of its package, and remove the plastic protective cover from the toner cartridge.
Page 318
318Replacing Consumable Products 7. Insert the new cartridge into the printer. 8. Close the toner cartridge cover.
Page 319
Replacing Consumable Products319 9 9 9 9 9 9 9 9 9 9 9 9 9. Close cover D. Photoconductor Unit Handling precautions Always observe the following handling precautions when replacing the consumable products: ❏The photoconductor unit weighs 1.3 kg (2.9 lb). Be sure to hold it firmly by the handle when carrying it. ❏When replacing the photoconductor unit, avoid exposing it to room light any longer than three minutes. ❏Be careful not to scratch the surface of the drum. Also, avoid touching the drum,...
Page 320
320Replacing Consumable Products ❏When storing the photoconductor unit, make sure to attach the protective cover to the photoconductor unit and put it in the sealed blackout package and the box in which the photoconductor unit was sold, and store it in a safe level place. ❏Do not tilt the photoconductor unit. w Warning: ❏Do not dispose of the used consumable products in fire, as it may explode and cause injury. Dispose of it according to local regulations. ❏Keep the consumable products out of the...