Electrolux Ews 106410 W User Manual

							ProblemPossible cause/Solution
The machine does not start:
The door has not been closed. E40
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the button 8 has
not been pressed.
• Please turn the selector dial and press the button 8 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay
start.
The Child Safety Lock has been activated.
• Deactivate the Child Safety Lock.
The machine does not fill:
The water tap is closed. E10
• Open the water tap.
The inlet hose is squashed or kinked. E10
• Check the inlet hose connection.
The filter in the inlet hose is blocked. E10
• Clean the water inlet hose filter.
The door is not properly closed. E40
• Close the door firmly.
The machine does not
empty and/or does not
spin:
The drain hose is squashed or kinked. E20
• Check the drain hose connection.
The drain filter is clogged. E20
• Clean the drain filter.
An option or a programme that ends with the water still in the tub
or a that eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fit-
tings. It is not always easy to see this as the water runs down the
hose; check to see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The cap on the emergency emptying hose has not been replaced
or the filter has not been properly screwed in after cleaning action.
• Refit the cap on the emergency emptying hose or screw the fil-
ter fully in.
Unsatisfactory washing re-
sults:
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
electrolux 21
 
						

							ProblemPossible cause/Solution
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the pilot light 9 goes off.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
Spinning starts late or the
machine does not spin:
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is redis-
tributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can
resume. If, after 10 minutes, the laundry is still not evenly distrib-
uted in the drum, the machine will not spin. In this case, redistrib-
ute the load manually and select the spin programme.
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select
the spinning programme.
The machine makes an un-
usual noise:The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor en-
sures a softer start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of the machine.
No water is visible in the
drum:Machines based on modern technology operate very economically
using very little water without affecting performance.
If you are unable to identify or solve the
problem, contact our service centre. Before
telephoning, make a note of the model, se-
rial number and purchase date of your ma-
chine: the Service Centre will require this
information.
Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
Mo
d. ..
. ..
. ...
Pro
d
. No.
 ..
. 
... ..
  
    
   
    
  
         
 S
er.  N
o
. .
.. ..
.
 ...
TECHNICAL DATA
DimensionsWidth
Height
Depth60 cm
85 cm
44 cm
22 electrolux
 
						

							Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating
plate, on the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton6 kg
Spin SpeedMaximum1000 rpm
INSTALLATION
Unpacking
All transit bolts and packing must be re-
moved before using the appliance.
You are advised to keep all transit devices
so that they can be refitted if the machine
ever has to be transported again.
1. After removing all the packaging, care-
fully lay machine on it’s back to remove
the polystyrene base from the bottom.2. Remove the power supply cable and the
draining hose from the hose holders on
the rear of the appliance.
3. Unscrew the three bolts.
electrolux 23
 
						

							4. Slide out the relevant plastic spacers.
5. Fill the smaller upper hole and the two
large ones with the corresponding plas-
tic plug caps supplied in the bag con-
taining the instruction booklet.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the
machine is not impeded by carpets, rugs
etc. Check that the machine does not
touch the wall or other kitchen units. Level
the washing machine by raising or lowering
the feet. The feet may be tight to adjust as
they incorporate a self locking nut, but the
machine MUST be level and stable. If nec-
essary, check the setting with a spirit level.
Any necessary adjustment can be made
with a spanner. Accurate levelling prevents
vibration, noise and displacement of the
machine during operation.Caution! Never place cardboard,
wood or similar materials under the
machine to compensate for any
unevenness in the floor.
Water inlet
An inlet hose is supplied and can been
found inside the machine drum. Do not use
the hose from your previous machine to
connect to the water supply.
Important! This appliance must be con-
nected to a cold water supply.
1. Open the porthole and extract the inlet
hose.
2. Connect the hose with the angled con-
nection to the machine. Do not place
the inlet hose downwards. Angle the
hose to the left or right depending on
the position of your water tap.
45°
35°
24 electrolux
 
						

							3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied
with the appliance.
The inlet hose must not be lengthened. If it
is too short and you do not wish to move
the tap, you will have to purchase a new,
longer hose specially designed for this type
of use.
Water-stop device
The inlet hose is provided with a water stop
device, which protects against damage
caused by water leaks in the hose which
could develop due to natural ageing of the
hose. This fault is shown by a red sector in
the window «A». Should this occur, turn the
water tap off and refer to your Service Cen-
tre to replace the hose.
A
Water drainage
The end of the drain hose can be posi-
tioned in three ways.
•Hooked over the edge of a sink using
the plastic hose guide supplied with the
machine. In this case, make sure the end
cannot come unhooked when the ma-
chine is emptying. This could be done by
tying it to the tap with a piece of string or
attaching it to the wall.
•In a sink drain pipe branch. This
branch must be above the trap so that
the bend is at least 60 cm above the
ground.
•Directly into a drain pipe at a height of
not less than 60 cm and not more than
90 cm. The end of the drain hose must
always be ventilated, i.e. the inside diam-
eter of the drain pipe must be larger than
the outside diameter of the drain hose.
The drain hose must not be kinked.
electrolux 25
 
						

							The drain hose may be extended to a maximum of 4 metres. An additional drain hose
and joining piece is available from your local Service Centre.
26 electrolux
 
						

							27  electrolux 
Electrolux.CI37\¼3‚
=ðb] ™öelectrolux.com 
I}e“
.#÷j—Jt 27
 29
66$Åiñ: 30
 32
š!I%¥\¼.) 32
8t0ÇG· 33.uG·9&KÉT–6_KÉ 36 
?¦LšZ÷ 37
lk™T–@”Aã 42
7Ôi+6!hó 46
5Zâ_V8( 49
.[l 49
,9˜^9ƒ2ä œ&uZÛb©Jt
.#÷j—Jt
d\\j—JtÝ]Z]h@!t š_V\™è µ,4(lN0!t
*8t2&RR’í
z374
						

							28  electrolux 
z5Uh
						

							  electrolux   29

374
						

							30  electrolux 
66$Åiñ:
!t