Electrolux Ews 106410 W User Manual

ProblemPossible cause/Solution
The machine does not start:
The door has not been closed. E40
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the button 8 has
not been pressed.
• Please turn the selector dial and press the button 8 again.
The delay start...

ProblemPossible cause/Solution
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the pilot light 9 goes off.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The...

Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating
plate, on the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton6 kg
Spin SpeedMaximum1000 rpm
INSTALLATION
Unpacking
All transit bolts and packing must be re-
moved before using the appliance.
You are advised to keep all transit devices
so that they can be refitted if the machine
ever has to be transported again.
1. After removing all...

4. Slide out the relevant plastic spacers.
5. Fill the smaller upper hole and the two
large ones with the corresponding plas-
tic plug caps supplied in the bag con-
taining the instruction booklet.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the
machine is not impeded by carpets, rugs
etc. Check that the machine does not
touch the wall or other kitchen units. Level
the washing machine by raising or lowering
the feet. The feet may be tight to adjust as
they...

3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied
with the appliance.
The inlet hose must not be lengthened. If it
is too short and you do not wish to move
the tap, you will have to purchase a new,
longer hose specially designed for this type
of use.
Water-stop device
The inlet hose is provided with a water stop
device, which protects...

The drain hose may be extended to a maximum of 4 metres. An additional drain hose
and joining piece is available from your local Service Centre.
26 electrolux
 

27  electrolux 
Electrolux.CI37\¼3‚
=ðb] ™öelectrolux.com 
I}e“
.#÷j—Jt 27
 29
66$Åiñ: 30
 32
š!I%¥\¼.) 32
8t0ÇG· 33.uG·9&KÉT–6_KÉ 36 
?¦LšZ÷ 37
lk™T–@”Aã 42
7Ôi+6!hó 46
5Zâ_V8( 49
.[l 49
,9˜^9ƒ2ä œ&uZÛb©Jt
.#÷j—Jt
d\\j—JtÝ]Z]h@!t š_V\™è µ,4(lN0!t
*8t2&RR’í
z374

28  electrolux 
z5Uh

  electrolux   29

374

30  electrolux 
66$Åiñ:
!t