Electrolux Ewg 14550 W User Manual

Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
Mod. ..
. ... ...
Prod. No.
 ..
. ... ..
         
      
         
 Ser. N
o. .
.. ...
 ...
Technical data
DimensionsWidth
Height
Depth (door included)60 cm
82 cm
54 cm
Electrical connectionInformation on the electrical connection is given on the rating plate,
on the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton6 kg
Spin SpeedMaximum1400 rpm
Consumption values
ProgrammeEnergy...

Installation
Unpacking
All transit bolts and packing must be re-
moved before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable, the
draining hose and inlet hose (if mounted)
from the hose holders on the rear of the
appliance.
3. Unscrew and remove the central...

BBC
C
5. Remove the bracket D and tighten up the
six smaller bolts C .
D
CC
6. Fill the smaller upper hole and the two
large ones with the corresponding plastic
plug caps supplied in the bag containing
the instruction booklet.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine
is not impeded by carpets, rugs etc. Check
that the machine does not touch the wall or
other kitchen units. Level the washing ma-
chine by raising or lowering the feet. The feet...

Caution! Never place cardboard, wood
or similar materials under the machine to
compensate for any unevenness in the
floor. After having levelled the appliance,
tighten the lock nuts.
Water inlet
An inlet hose is supplied and can been found
inside the machine drum. Do not use the
hose from your previous machine to connect
to the water supply.
Important! This appliance must be con-
nected to a cold water supply.
1. Open the porthole and extract the inlet
hose.
2. Connect the hose with the angled con-...

•
Hooked over the edge of a sink using
the plastic hose guide supplied with the
machine. In this case, make sure the end
cannot come unhooked when the ma-
chine is emptying. This could be done by
tying it to the tap with a piece of string or
attaching it to the wall.•
In a sink drain pipe branch. This branch
must be above the trap so that the bend is
at least 60 cm above the ground.
•Directly into a drain pipe at a height of
not less than 60 cm and not more than 90
cm. The end of the drain hose must...

Should the appliance power supply
cable need to be replaced, this must
be carried out by a Service Centre.
Environment concerns
The symbol    on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health,...

- thickness 16-22 mm
The height (C-Fig. C) depends on the height
of the adjacent furnitures base.
C
b) Hinges
To mount the hinges it is necessary to drill
two holes (dia. 35 mm, depth 12.5-14 mm
depending on the depth of door furniture) on
the inner side of the door. The distance be-
tween the holes hobs fixing centres must be
416 mm.
The distance (B) from upper edge of the door
to the centre of the hole depends on the ad-
jacent furnitures dimensions.
The required dimensions are given in the pic-
ture...

132957250-00-092009
www.electrolux.com