Electrolux Ewg 14550 W User Manual

							Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
Mod. ..
. ... ...
Prod. No.
 ..
. ... ..
         
      
         
 Ser. N
o. .
.. ...
 ...
Technical data
DimensionsWidth
Height
Depth (door included)60 cm
82 cm
54 cm
Electrical connectionInformation on the electrical connection is given on the rating plate,
on the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton6 kg
Spin SpeedMaximum1400 rpm
Consumption values
ProgrammeEnergy consumption
(KWh)Water consumption
(litres)Programme duration
(Minutes)
White Cottons 90°2.157
For the duration of
the programmes,
please refer to the
display on the con-
trol panel.Cottons 60°1.253
Cotton ECO 60° 1)1.0252
Cottons 40°0.753
Synthetics 40°0.540
Delicates 40°0.5556
Wool/ Handwash 30°0.2558
1) «Cottons Eco» at 60°C with a load of 6 kg is the reference programme for the data entered in the
energy label, in compliance with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it
may vary depending on the quantity and type of laundry, on the inlet water temperature
and on the ambient temperature.
electrolux  21
 
						

							Installation
Unpacking
All transit bolts and packing must be re-
moved before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable, the
draining hose and inlet hose (if mounted)
from the hose holders on the rear of the
appliance.
3. Unscrew and remove the central rear bolt
A with the supplied spanner . Slide out
the relevant plastic spacer.
4. Unscrew and remove the two large rear
bolts B and the six smaller bolts C .
22  electrolux
 
						

							BBC
C
5. Remove the bracket D and tighten up the
six smaller bolts C .
D
CC
6. Fill the smaller upper hole and the two
large ones with the corresponding plastic
plug caps supplied in the bag containing
the instruction booklet.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine
is not impeded by carpets, rugs etc. Check
that the machine does not touch the wall or
other kitchen units. Level the washing ma-
chine by raising or lowering the feet. The feet
may be tight to adjust as they incorporate a
self locking nut, but the machine MUST be
level and stable. If necessary, check the set-
ting with a spirit level. Any necessary adjust-
ment can be made with a spanner.
Accurate levelling prevents vibration, noise
and displacement of the machine during op-
eration.
electrolux  23
 
						

							Caution! Never place cardboard, wood
or similar materials under the machine to
compensate for any unevenness in the
floor. After having levelled the appliance,
tighten the lock nuts.
Water inlet
An inlet hose is supplied and can been found
inside the machine drum. Do not use the
hose from your previous machine to connect
to the water supply.
Important! This appliance must be con-
nected to a cold water supply.
1. Open the porthole and extract the inlet
hose.
2. Connect the hose with the angled con-
nection to the machine. Do not place the
inlet hose downwards. Angle the hose to
the left or right depending on the position
of your water tap.
3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
45°
35°
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied
with the appliance.
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the
tap, you will have to purchase a new, longer
hose specially designed for this type of use.
Water-stop device
The inlet hose is provided with a water stop
device, which protects against damage
caused by water leaks in the hose which
could develop due to natural ageing of the
hose. This fault is shown by a red sector in
the window «A» . Should this occur, turn the
water tap off and refer to your Service Centre
to replace the hose.
A
Water drainage
The end of the drain hose can be positioned
in three ways.
24  electrolux
 
						

							•
Hooked over the edge of a sink using
the plastic hose guide supplied with the
machine. In this case, make sure the end
cannot come unhooked when the ma-
chine is emptying. This could be done by
tying it to the tap with a piece of string or
attaching it to the wall.•
In a sink drain pipe branch. This branch
must be above the trap so that the bend is
at least 60 cm above the ground.
•Directly into a drain pipe at a height of
not less than 60 cm and not more than 90
cm. The end of the drain hose must always
be ventilated, i.e. the inside diameter of the
drain pipe must be larger than the outside
diameter of the drain hose. The drain hose
must not be kinked.
The drain hose may be extended to a maximum of 4 metres. An additional drain hose and
joining piece is available from your local Service Centre.
Electrical connection
Information on the electrical connection is
given on the rating plate on the inner edge of
the appliance door.
Check that your domestic electrical installa-
tion can take the maximum load required, al-
so taking into account any other appliances
in use.
Connect the machine to an earthed
socket.
The manufacturer does not accept
any responsibility for damage or
injury through failure to comply with
the above safety precaution.
The power supply cable must be
easily accessible after installing the
machine.
electrolux  25
 
						

							Should the appliance power supply
cable need to be replaced, this must
be carried out by a Service Centre.
Environment concerns
The symbol    on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Packaging materials
The materials marked with the symbol 
 are
recyclable.
>PEPSPP
						

							- thickness 16-22 mm
The height (C-Fig. C) depends on the height
of the adjacent furnitures base.
C
b) Hinges
To mount the hinges it is necessary to drill
two holes (dia. 35 mm, depth 12.5-14 mm
depending on the depth of door furniture) on
the inner side of the door. The distance be-
tween the holes hobs fixing centres must be
416 mm.
The distance (B) from upper edge of the door
to the centre of the hole depends on the ad-
jacent furnitures dimensions.
The required dimensions are given in the pic-
ture C.
The hinges will be fixed to the door by means
of screws for wood (2-Fig. B) supplied with
the appliance.
c) Mounting the door
Fix the hinges (1) to the machine by means
of the M 5x15 screws (3-Fig. B). The hinges
can be adjusted to compensate for possible
uneven thickness of the door.
To align the door perfectly it is necessary to
loosen the screw (3-Fig. B), adjust the door
and tighten the screw again.
d) Counter-magnet (6)
The appliance is prearranged for a magnetic
closure of the door.
To enable a correct operation of this device,
it is necessary to screw the counter-magnet
(6) (steel disk + rubber ring) into the inner side
of the door. Its position must correspond to
the magnet (4) on the appliance (see picture
D).D
6
4
If the door has to be opened from left to right,
invert the position of the plates (7), the mag-
net (4) and the plate (5) (Fig. B and E). Mount
the counter-magnet (6) and the hinges (1) as
previously described.
E
1
2 3 76
5 4
electrolux  27
 
						

							132957250-00-092009
www.electrolux.com