Electrolux Esf 63020 X Manual

1. After having selected the washing
programme, press the delay start
button.
– The corresponding indicator light
illuminates.
2. Press the start/cancel button, the
countdown of the delay start begins
automatically.
– The phase indicator lights turn off.
– The opening of the door will not
modify or interrupt the count-
down.
– Once the delay start has elapsed
the washing programme will start
automatically, the delay start indi-
cator light turns off while the indi-
cator light of the phase in progress...

will be cooler and the drying will be
improved.
Unloading the dishwasher
• Hot dishes are sensitive to knocks.
The dishes should therefore be al-
lowed to cool down before removing
from the appliance.
• Empty the lower basket first and then
the upper one; this will avoid water
dripping from the upper basket onto
the dishes in the lower one.
• Water may appear on the sides and
the door of the dishwasher as thestainless steel will eventually become
cooler than the dishes.
When the washing programme has...

ProgrammeDegree of soilType of loadProgramme de-
scription
C
Quick
1)
Normal or light soilCrockery and cut-
leryMain wash up to
60°C
Final rinse
D
Eco 50°
2)
Normal soilCrockery and cut-
leryPrewash
Main wash up to
50°C
1 intermediate
rinse
Final rinse
Drying
E
Rinse and Hold
Any.
Partial load (to be completed later in the
day).1 cold rinse (to
avoid food scraps
from sticking
together).
This programme
does not require
the use of deter-
gent.
1) Ideal for washing a partially loaded dishwasher. This is the...

3.
Turn the handle about 1/4 a turn an-
ticlockwise and remove the filter sys-
tem.
4. Take hold of the coarse filter (A) by
the handle with the hole and remove
from the microfilter (B).
5. Clean all filters thoroughly under run-
ning water.
6. Remove the flat filter from the base
of the washing compartment and
clean both faces thoroughly.7.
Put the flat filter back in the base of
the washing compartment and en-
sure that it fits perfectly under the
two guides (C).
8. Place the coarse filter (A) in the...

NEVER use the dishwasher without
filters. Incorrect repositioning and
fitting of the filters will produce poor
washing results and may result in
damage to the appliance.
Cleaning the spray arms
NEVER try to remove the spray
arms.
If residues of soil have clogged the holes
in the spray arms, remove them with a
cocktail stick.
External cleaning
Clean the external surfaces of the ma-
chine and control panel with a damp soft
cloth. If necessary use only neutral de-
tergents. Never use abrasive products,...

Something not working
The dishwasher will not start or stops
during operation.
Certain problems are due to the lack of
simple maintenance or oversights,
which can be solved with the help of theindications described in the chart, with-
out calling out an engineer.
Switch off the dishwasher, open the
door and carry out the following sugges-
ted corrective actions.
Fault code and malfunctionPossible cause and solution
• continuous flashing of the start/can-
cel indicator light
• 1 flash of the end of...

Fault code and malfunctionPossible cause and solution
• The programme does not start• The dishwasher’s door has not been
properly closed
Close the door
• The main plug is not plugged in
Insert the main plug
• The fuse has blown out in the house-
hold fuse box
Replace the fuse
• Delay start has been set
If dishes are to be washed immediately,
cancel the delay start
Once these checks have been carried
out, switch on the appliance: the pro-
gramme will continue from the point at
which it was interrupted.
If...

The wash results are not satisfactory
The dishes are not clean• The wrong washing programme has
been selected.
• The dishes are arranged in such a
way as to stop water reaching all
parts of the surface. The baskets
must not be overloaded.
• The spray arms do not rotate freely
due to incorrect arrangement of the
load.
• The filters in the base of the washing
compartment are dirty or incorrectly
positioned.
• Too little or no detergent has been
used.
• Where there are limescales deposits
on the dishes; the...

Technical data
DimensionsWidth x Height x Depth
(cm)60,0 x 85,0 x 61,0
Electrical connection
Voltage - Overall power -
FuseInformation on the electrical connection is given on the
rating plate on the inner edge of the dishwasher’s
door.
Water supply pressureMinimum - Maximum
(MPa)0,05 - 0,8
Capacityplace settings12
Max. weightkg40,5
Noise leveldB(A)49
Consumption values
Consumption values
ProgrammeProgramme du-
ration (in mi-
nutes)Energy con-
sumption (in
kWh)Water (litres)
Intensive85-951,8-2,022-25...

Hints for test institutes
Testing in accordance with EN 60704
must be carried out with appliance fully
loaded and using the test programme
(see Consumption values).
Test in accordance with EN 50242 must
be carried out when the salt containerand rinse aid dispenser have been filled
with salt and rinse aid respectively and
using the test programme (see
Consumption values).
Full load: 12 standard place settings
Amount of detergent required5 g + 25 g (Type B)
Rinse aid settingposition 4 (Type III)
Lower...