Eizo Flexscan S2433w Users Manual

							41Chapter 5  Reference
• USB port
	
UpstreamSeries A connector
Series B connector Upstream
Contact No. Signal
Remarks
1 VCC
Cable
	power
2 – Data
Serial data
3 +
	Data
Serial data
4 Ground
Cable
	ground
Accessories List
Cleaning Kit EIZO	ScreenCleaner
Speaker Unit i•Sound
	L3*
Signal
	Cable PP200
* May not allowed to attach the option speaker depending on the stand type.
For the latest information about the accessories, refer to our web site.
http://www.eizo.com
  
						

							42Chapter 5  Reference
5-4 Glossary
ClockThe analog input monitor needs to reproduce a clock of the same frequenc\
y as the dot clock of the graphics system in 
use, when the analog input signal is converted to a digital signal for image display . 
This is called clock adjustment. If the clock pulse is not set correctly , some vertical bars appear on the screen.
DDC/CI (Display Data Channel/Command Interface) VESA provides the standardization for the interactive communication of the setting information, etc. between a PC 
and the monitor.
DisplayPort VESA provides the digital interface standard for the digital display device. DisplayPort can transfer the video signal 
up to 16 bits for each channel of RGB, and the audio signal too. (This monitor supports the 8-bit video signal only .)
DVI (Digital Visual Interface) DVI is a digital interface standard. DVI allows direct transmission of the PC’ s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors. One is 
a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and analog signal 
inputs.
DVI DMPM (DVI Digital Monitor Power Management) DVI DMPM is a digital interface power-saving function. The “Monitor ON (operating mode)” and “Active Off 
(power-saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain This is used to adjust each color parameter for red, green and blue.  An LCD monitor displays the color by the light 
passing through the panel color filter. Red, green and blue are the three primary colors. All the colors on the screen 
are displayed by combining these three colors. The color tone can be changed by adjusting the light intensity (volume) 
passing through each color’s filter.
Gamma Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma 
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a high-
contrast image.
HDCP (High-bandwidth Digital Contents Protection) Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc.  This helps 
to transmit the digital contents safely by coding the digital contents sent via DVI terminal on the output side and 
decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not applicable 
to HDCP system.
Phase Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is made to 
adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted correctly .
Range Adjustment Range adjustment controls the signal output levels to display every color gradation. It is recommended that range 
adjustment be made before color adjustment.
  
						

							43Chapter 5  Reference
ResolutionThe LCD panel consists of numerous pixels of specified size, which are illuminated to form images.  This monitor
consists of 1920 horizontal pixels and 1200 vertical pixels. At a resolution of 1920×1200, all pixels are illuminated as 
a full screen (1:1).
sRGB (Standard RGB) International standard for “color reproduction and color space” am\
ong peripheral devices (such as monitors, printers, 
digital cameras, scanners). sRGB allows Internet users to closely match colors as a simple color matching means for 
the Internet use.
Temperature Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin.  The screen 
becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.
5000K: Slightly reddish white
6500K: Warm white like paper white
9300K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling) A signal transmission system for digital interface.
VESA DPMS (Video Electronics Standards Association - Display Power Management Signaling) VESA provides the standardization of signals from PC (graphics board) for power saving of PC monitors. DPMS 
defines the signal status between PC and monitor.
  
						

							44Chapter 5  Reference
5-5 Preset Timing
The following table shows factory preset video timing (for analog signal only).
ModeDot clock Frequency
PolarityHorizontal: kHz
Vertical: Hz
VGA 640×480@60Hz 25.2 MHz Horizontal 31.47 Negative
Vertical 59.94 Negative
VGA TEXT  
720×400@70Hz 28.3 MHzHorizontal 31.47 Negative
Vertical 70.09 Positive
VESA 640×480@73Hz 31.5 MHz Horizontal 37.86 Negative
Vertical 72.81 Negative
VESA 640×480@75Hz 31.5 MHz Horizontal 37.50 Negative
Vertical 75.00 Negative
VESA 800×600@56Hz 36.0 MHz Horizontal 35.16 Positive
Vertical 56.25 Positive
VESA 800×600@60Hz 40.0 MHz Horizontal 37.88 Positive
Vertical 60.32 Positive
VESA 800×600@72Hz 50.0 MHz Horizontal 48.08 Positive
Vertical 72.19 Positive
VESA 800×600@75Hz 49.5 MHz Horizontal 46.88 Positive
Vertical 75.00 Positive
VESA 1024×768@60Hz 65.0 MHz Horizontal 48.36 Negative
Vertical 60.00 Negative
VESA 1024×768@70Hz 75.0 MHz Horizontal 56.48 Negative
Vertical 70.07 Negative
VESA 1024×768@75Hz 78.8 MHz Horizontal 60.02 Positive
Vertical 75.03 Positive
VESA 1152×864@75Hz 108.0 MHz Horizontal 67.50 Positive
Vertical 75.00 Positive
VESA 1280×960@60Hz 108.0 MHz Horizontal 60.00 Positive
Vertical 60.00 Positive
VESA 1280×1024@60Hz 108.0 MHz Horizontal 63.98 Positive
Vertical 60.02 Positive
VESA 1280×1024@75Hz 135.0 MHz Horizontal 79.98 Positive
Vertical 75.03 Positive
VESA 1600×1200@60Hz  162.0 MHz Horizontal 75.00 Positive
Vertical 60.00 Positive
VESA 1600×1200@65Hz  175.0 MHz Horizontal 81.25 Positive
Vertical 65.00 Positive
VESA 1600×1200@70Hz  189.0 MHz Horizontal 87.50 Positive
Vertical 70.00 Positive
VESA 1600×1200@75Hz  202.5 MHz Horizontal 93.75 Positive
Vertical 75.00 Positive
VESA CVT  
1680×1050@60Hz 146.3 MHzHorizontal 65.29 Negative
Vertical 59.95 Positive
VESA CVT 
1920×1200@60Hz  193.3 MHzHorizontal 74.56 Negative
Vertical 59.89 Positive
VESA CVT RB  
1920×1200@60Hz  154.0 MHzHorizontal 74.04 Positive
Vertical 59.95 Negative
Attention
• Display position may be deviated 
depending on the PC connected, 
which may require screen adjustment 
using Adjustment menu.
•
 If a signal other than those listed i

n 
the table is input, adjust the screen 
using the Adjustment menu. However, 
screen display may still be incorrect 
even after the adjustment.
•
 When interlace 

signals are used, the 
screen cannot be displayed correctly 
even after screen adjustment using the 
Adjustment menu.
   
						

							45 
For U.S.A. , Canada, etc. (rated 100-120 Vac) OnlyFCC
	Declaration	of	Conformity
We,	the	Responsible	Party EIZO NANAO TECHNOLOGIES INC.
5710 
Warland Drive, Cypress, CA 90630
Phone:  (562) 431-5011
declare
	that	the	pr

oduct Trade name:  EIZO
Model:  FlexScan S2433W
is
	in	conformity	with	Part	15	of	the	FCC	Rules.	Operation	of	this	pr

oduct
	is	subject	to	the	following	two	
conditions:	(1)	this	device	may	not	cause	harmful	interfer

ence,
	and	(2)	this	device	must	accept	any	
interference	r

eceived,
	including	interfer
 ence
	that	may	cause	undesir
 ed
	operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 
of the FCC Rules.  

These limits are designed to provide reasonable protection against harmful interference in a 
residential installation.  This equipment generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications.  However , 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment of f and on, the user 
is encouraged to try to correct the interference by one or more of the following measures.
*
 Reorient or relocate the receiv

ing antenna.
*
 Increase the separation between the equipment and receiver

.
*
 Connect the e

quipment into an outlet on a circuit different from that to which the receiver is connected.
*
 Consult the dealer or an expe

rienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user ’s 
authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the 
limits of a Class B digital device.
-
 AC Cord
-
 Shielded Signal Cable (enclosed)
Canadian	Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
FCC Declaration of Conformity
  
						

							46 
Hinweise	zur	Auswahl	des	richtigen	Schwenkarms	für	Ihren	Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vor gesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a)
 Der Standfuß 

muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät 
und  des  spezifizierten  Zubehörs  besitzen.  Das  Gewicht  des  Bildschirmgerätes  und  des  Zubehörs  sind  in  der 
zugehörenden Bedienungsanleitung angegeben.
b)
 Die Befestigung 

des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher 
als die Augenhöhe eines Benutzers in sitzender Position ist.
c)
 Im Fall 

eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der 
Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.
d)
 Der Standfuß 

muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach 
hinten ≥ 5°).
e)
 Der  Standfuß 

muß  die  Möglichkeit  zur  Drehung  des  Bildschirmgerätes  besitzen  (max.  ±180°).  Der  maximale 
Kraftaufwand dafür muß weniger als 100 N betragen.
f)
 Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g)
 Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).
h)
 Der Standfuß 

mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position 
kippsicher sein.
Hinweis	zur	Ergonomie	:
Dieser Monitor erfüllt die  Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1920 × 
1200, Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non interlaced.  Weiterhin wird aus 
ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte 
Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)
Übermäßiger Schalldruck von Ohrhörern bzw. Kopfhörern kann einen Hörverlust bewirken.
Eine Einstellung des Equalizers auf Maximalwerte erhöht die Ausgangsspannung am Ohrhörer- bzw.
Kopfhörerausgang und damit auch den Schalldruckpegel.
„Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“
[Begrenzung des maximalen Schalldruckpegels am Ohr]
Bildschirmgeräte: Größte Ausgangsspannung 150 mV
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Hinweis zur Ergonomie
  
						

							Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Hinweis zur Ergonomie
关于电子信息产品污染控制标识
本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。
标识中央的数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制
造日起算的年限内，不会产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。
•有毒有害物质或元素的名称及含量 
部件名称有毒有害物质或元素
铅
（Pb） 汞
（Hg） 镉
（Cd） 六价铬 
（Cr（VI）） 多溴联苯
（PBB） 多溴二苯醚
（PBDE）
印刷电路板 ×○ ○ ○ ○○
机箱 ○ ○ ○ ○ ○○
液晶显示器 × ×○ ○ ○○
其他 ×○ ○ ○ ○○
○ ： 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。
× ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T  11363-2006 规定的限量要求。( 企业可
在此处 , 根据实际情況对上表中打“×
”
的技术原因进行进一步说明 )
 
						

							2nd Edition-August, 2011
03V23255B1
(U.M-S2433W-FS)