Eizo Flexscan S2111w Users Manual

							
29Chapter 5  Reference
Attention
•  Never use any solvents or chemicals, such as thinner, benzene, wax, 
alcohol, and abrasive cleaner, which 
may damage the cabinet or LCD 
panel.
NOTE
•  Optional ScreenCleaner is recommended for cleaning the panel 
surface.
5-2 Cleaning
Clean the monitor periodically to keep the monitor clean and extend its \
life.
Cabinet
Clean the cabinet with a soft cloth dampened with little mild detergent.
LCD Panel
•  Clean the LCD panel with a soft cloth such as cotton cloth or lens clean\
ing 
paper. 
•  Remove persistent stains gently with a cloth dampened with little water, and  then clean the LCD panel again with a dry cloth for better  fi nishing.
S 2111W _U M _E N _v1 .3 .in dd   2 9S2111W_UM_EN_v1.3.indd   293/2 /2 007   6 :5 5:1 0 P M3/2/2007   6:55:10 PM 
						

							
30Chapter 5  Reference
5-3 Specifi cations
S 2 111 W
LCD Panel 21.1-inch (539 mm) TFT color LCD with anti-glare hard coating 
Viewing angle: Vertical 178°, Horizontal 178°(CR:10 or more)
Dot Pitch 0.270mm
Horizontal Scan Frequency Analog: 24-82kHz (Automatic) Digital: 31-65kHz
Vertical Scan Frequency Analog: 49-86Hz (Automatic)  (1280 × 1024: 49-76Hz, 1680 × 1050: 49-61Hz)
Digital: 59-61Hz 
(VGA TEXT: 69-71Hz)
Resolution 1680 dots × 1050 lines
Max. Dot Clock Analog: 150MHz Digital: 120MHz
Max. Display Color 1677 million colors
Display Area (H × V) 453.6mm × 283.5mm
Power Supply 100 - 120 VAC ±10%, 50/60Hz 0.9A 200 - 240 VAC ±10%, 50/60Hz 0.45A
Power Consumption Max.: 90W (with USB load) Min.: (normal mode) (without USB load): 80W
Power saving mode: 2W or less (for single signal input) 
Power switch Off: 1W or less
Input Signal Connector DVI-I connector (Applicable to HDCP) × 2
Analog Input Signal (Sync) a) Separate, TTL, positive/ negative b) Composite, TTL, positive/ negative
Analog Input Signal (Video) Analog, Positive (0.7Vp-p/75 Ω)
Digital Signal Transmission 
System TMDS (Single Link)
Video Signal Memory Analog signal: 45 (preset: 24) Digital signal: 10 (preset: 0)
Plug & Play VESA DDC 2B
Dimensions (Main unit) 501mm (19.7 inch)(W) × 341.1-459.5mm (13.4-18.1 inch)(H) ×\
 230mm (9.1 inch)(D)
Dimensions (without Stand) 501mm (19.7 inch)(W) × 355mm (13.9 inch)(H) × 85mm (3.4 i\
nch)(D)
Weight (Main unit) 8.2kg (18.0 lbs)
Weight (without Stand) 5.8kg (12.8 lbs)
Environmental Conditions Operating temperature: 0 °C - 35 °C Storage temperature: -20 °C - 60 °C
Relative humidity: 30% - 80% (no condensation)
USB Standard USB Speci fi cation Revision 2.0
USB Port Upstream port × 1 Downstream port × 2
S 2111W _U M _E N _v1 .3 .in dd   3 0S2111W_UM_EN_v1.3.indd   303/2 /2 007   6 :5 5:1 0 P M3/2/2007   6:55:10 PM 
						

							
31Chapter 5  Reference
S2411W
LCD Panel 24.1-inch (610 mm) TFT color LCD with anti-glare hard coatingViewing angle: Vertical 178°, Horizontal 178°(CR:10 or more)
Dot Pitch 0.270mm
Horizontal Scan Frequency Analog: 24-94kHz (Automatic) Digital: 31-76kHz
Vertical Scan Frequency Analog: 49-86Hz (Automatic)  (1600 × 1200: 49-76Hz, 1920 × 1200: 49-61Hz)
Digital: 59-61Hz (VGA TEXT: 69-71Hz) (1080p@50Hz: 49-51Hz)
Resolution 1920 dots × 1200 lines
Max. Dot Clock Analog: 202.5MHz Digital: 162MHz
Max. Display Color 1677 million colors
Display Area (H × V) 518.4mm × 324.0mm
Power Supply 100-120 VAC ±10%, 50/60Hz 1.1A 200-240 VAC ±10%, 50/60Hz 0.55A
Power Consumption Max.: 110W ( with USB load) Min.: (normal mode) (without USB load): 100W
Power saving mode: 2W or less (for single signal input) 
Power switch Off: 1W or less
Input Signal Connector DVI-I connector (Applicable to HDCP) × 2
Analog Input Signal (Sync) a) Separate, TTL, positive/ negative b) Composite,  TTL,  positive/  negative
Analog Input Signal (Video) Analog, Positive (0.7Vp-p/75 Ω)
Digital Signal Transmission 
System TMDS (Single Link)
Video Signal Memory Analog signal: 45 (preset: 30) Digital signal: 10 (preset: 0)
Plug & Play VESA DDC 2B
Dimensions (Main unit) 566mm (22.3 inch)(W) × 358.7-480mm (14.1-189.9 inch)(H) × \
230mm (9.1 inch)(D)
Dimensions (without Stand) 566mm (22.3 inch)(W) × 396mm (15.5 inch)(H) × 85mm (3.4 i\
nch)(D)
Weight (Main unit) 10.2kg (22.4 lbs)
Weight (without Stand) 7.8kg (17.2 lbs)
Environmental Conditions Operating temperature: 0 °C - 35 °C Storage temperature: -20 °C - 60 °C
Relative humidity: 30% - 80% (no condensation)
USB Standard USB Speci fi cation Revision 2.0 
USB Port Upstream port × 1 Downstream port × 2
S 2111W _U M _E N _v1 .3 .in dd   3 1S2111W_UM_EN_v1.3.indd   313/2 /2 007   6 :5 5:1 0 P M3/2/2007   6:55:10 PM 
						

							
32Chapter 5  Reference
Main default settings (factory settings)
Analog Input Digital Input
Smoothing 3
FineContrast Mode  Custom
PowerManager VESA DPMS DVI DMPM
Screen Size Full Screen
Input Priority 1
Off Timer Disable
Menu Settings Menu Size Normal
Menu Off Timer 45sec
Beep On
Language English
Outside Dimensions
S 2 111 W
294(11.6)
25
(0.98)14.5(0.57)
116(4.6)
80(3.15)
100(3.9)
100(3.9)
344.2(13.6) 230(9.1)
21.7(0.85)
341.1(13.4)
55.6(17.9)
501(19.7)
22.7(0.89)TILT
22.7(0.89)
22.75(0.9) 285.5(11.2)
24(0.94) 331(13.0)
459.5(18.1)
457.6(18.0)
unit : mm (inch)
S 2111W _U M _E N _v1 .3 .in dd   3 2S2111W_UM_EN_v1.3.indd   323/2 /2 007   6 :5 5:1 0 P M3/2/2007   6:55:10 PM 
						

							
33Chapter 5  Reference
S2411W
unit : mm (inch)
Connector Pin Assignment
• DVI-I connector 
 123
4
56
78
910 11 12
1314 15
16
19 20 21
17 18 22 23 24C1C2C3C4
C5
Pin No.SignalPin No.SignalPin No.Signal 
1 TMDS Data 2- 11 TMDS Data1/3 Shield 21 NC*
2 TMDS Data 2+ 12 NC* 22 TMDS Clock shield
3 TMDS Data2/4 Shield 13 NC* 23 TMDS Clock+
4 NC* 14 +5V Power 24 TMDS Clock-
5 NC* 15 Ground (return for +5V,  Hsync and Vsync)C1 Analog Red
6 DDC Clock (SCL) 16 Hot Plug Detect C2 Analog Green
7  DDC Data (SDA) 17  TMDS Data0- C3 Analog Blue
8 Analog Vertical Sync 18 TMDS Data0+ C4 Analog Horizontal Sync
9 TMDS Data1- 19 TMDS Data0/5 Shield C5 Analog Ground (analog  R,G,&B return)
10 TMDS Data1+ 20 NC* (NC*: No Connection)
566(22.3)
372(14.6)
294(11.6)
7.3
(0.29) 357.2(14.1)
361.9(14.2)
60.5(2.38) 23.5(0.93)
522(20.6)
24(0.94)
520.4(20.5)
326(12.8)
22.8(0.9)
25
(0.98)116(4.6)
14.5(0.57)
80(3.15)
TILT
ARCSWING
480(18.9)
230(9.1)
S2111W _U M _E N _v1 .3 .in dd   3 3S2111W_UM_EN_v1.3.indd   333/2 /2 007   6 :5 5:1 3 P M3/2/2007   6:55:13 PM 
						

							
34Chapter 5  Reference
• USB port
 
Upstream
Series B connectorDownstream
Series A  connector
Contact No. Signal Remarks 1 VCC Cable power
2 – Data Serial data
3 + Data Serial data
4 Ground Cable ground
Option List
Cleaning Kit EIZO ScreenCleaner
Signal Cable FD-C16
FD-C39
S
2111W _U M _E N _v1 .3 .in dd   3 4S2111W_UM_EN_v1.3.indd   343/2 /2 007   6 :5 5:1 7 P M3/2/2007   6:55:17 PM 
						

							
35Chapter 5  Reference
5-4 Glossary
ClockThe analog input monitor needs to reproduce a clock of the same frequenc\
y as the dot clock of the graphics system in 
use, when the analog input signal is converted to a digital signal for i\
mage display. 
This is called clock adjustment. If the clock pulse is not set correctly\
, some vertical bars appear on the screen.
DVI (Digital Visual Interface) DVI is a digital interface standard. DVI allows direct transmission of t\
he PC’s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors. One is 
a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and analog signal 
inputs.
DVI DMPM (DVI Digital Monitor Power Management) DVI DMPM is a digital interface power-saving function. The “Monitor ON (operating mode)” and “Active Off 
(power-saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
ContrastEnhancer ContrastEnhancer functions to reproduce images with a taste of contrast \
by compensating the gamma value as well as 
controlling the backlight brightness and the gain level according to the\
 image status.
Gain This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by the light 
passing through the panel color  fi lter. Red, green and blue are the three primary colors. All the colors on the screen 
are displayed by combining these three colors. The color tone can be changed by adjusting the light intensity (volume)\
 
passing through each color’s  fi lter.
Gamma Generally, the monitor brightness varies nonlinearly with the input signal level,\
 which is called “Gamma 
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a high-
contrast image.
HDCP (High-bandwidth Digital Contents Protection) Digital signal coding system developed to copy-protect the digital conte\
nts, such as video, music, etc. This helps 
to transmit the digital contents safely by coding the digital contents s\
ent via DVI terminal on the output side and 
decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on t\
he output and input sides are not applicable 
to HDCP system.
OutlineEnhancer OutlineEnhancer functions to emphasize outline of the images by emphasiz\
ing the color difference between pixels 
composing the images. This may improve the texture of the material and its feel of the images.\
On the contrary, it also functions to reproduce the images smoothly by gradating its ou\
tline.
Phase Phase means the sampling timing to convert the analog input signal to a \
digital signal. Phase adjustment is made to 
adjust the timing. It is recommended that phase adjustment be made after\
 the clock is adjusted correctly.
Range Adjustment Range adjustment controls the signal output levels to display every colo\
r gradation. It is recommended that range 
adjustment be made before color adjustment.
S2111W _U M _E N _v1 .3 .in dd   3 5S2111W_UM_EN_v1.3.indd   353/2 /2 007   6 :5 5:1 7 P M3/2/2007   6:55:17 PM 
						

							
36Chapter 5  Reference
ResolutionThe LCD panel consists of numerous pixels of speci fi ed size, which are illuminated to form images. This monitor 
consists of 1680 (S2111W) / 1920 (S2411W) horizontal pixels and 1050 (S2111W) / 1200 (S2411W) vertical pixels. 
At a resolution of 1680 x 1050 (S2111W) / 1920 x 1200 (S2411W), all pixels are illuminated as a full screen (1:1).
sRGB (Standard RGB) International standard for “color reproduction and color space” am\
ong peripheral devices (such as monitors, printers, 
digital cameras, scanners). sRGB allows Internet users to closely match\
 colors as a simple color matching means for 
the Internet use.
Temperature Color temperature is a method to measure the white color tone, generally\
 indicated in degrees Kelvin. The screen 
becomes reddish at a low temperature, and bluish at a high temperature, \
like the  fl ame temperature.
5000K: Slightly reddish white
6500K: Warm white like paper white
9300K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling) A signal transmission system for digital interface.
VESA DPMS (Video Electronics Standards Association - Display Power Management Signaling) VESA provides the standardization of signals from PC (graphics board) for \
power saving of PC monitors. DPMS 
defi nes the signal status between PC and monitor.
S 2111W _U M _E N _v1 .3 .in dd   3 6S2111W_UM_EN_v1.3.indd   363/2 /2 007   6 :5 5:1 8 P M3/2/2007   6:55:18 PM 
						

							
37Chapter 5  Reference
5-5 Preset Timing
The following table shows factory preset video timing (analog signal on\
ly).
Mode Dot clockFrequency
PolarityHorizontal: kHz
Vertical: Hz
VGA 640×480@60Hz 25.2 MHz Horizontal 31.47 Negative
Vertical 59.94 Negative
VGA 720×400@70Hz 28.3 MHz Horizontal 31.47 Negative
Vertical 70.09 Positive
Macintosh 640×
480@67Hz 30.2 MHzHorizontal 35.00 Negative
Vertical 66.67 Negative
Macintosh 832×
624@75Hz 57.3 MHzHorizontal 49.72 Negative
Vertical 74.55 Negative
Macintosh 1152×
870@75Hz 100.0 MHzHorizontal 68.68 Negative
Vertical 75.06 Negative
Macintosh 1280×
960@75Hz 126.2 MHzHorizontal 74.76 Positive
Vertical 74.76 Positive
VESA 640×480@72Hz 31.5 MHz Horizontal 37.86 Negative
Vertical 72.81 Negative
VESA 640×480@75Hz 31.5 MHz Horizontal 37.50 Negative
Vertical 75.00 Negative
VESA 640×480@85Hz 36.0 MHz Horizontal 43.27 Negative
Vertical 85.01 Negative
VESA 800×600@56Hz 36.0 MHz Horizontal 35.16 Positive
Vertical 56.25 Positive
VESA 800×600@60Hz 40.0 MHz Horizontal 37.88 Positive
Vertical 60.32 Positive
VESA 800×600@72Hz 50.0 MHz Horizontal 48.08 Positive
Vertical 72.19 Positive
VESA 800×600@75Hz 49.5 MHz Horizontal 46.88 Positive
Vertical 75.00 Positive
VESA 800×600@85Hz 56.3 MHz Horizontal 53.67 Positive
Vertical 85.06 Positive
VESA 1024×768@60Hz 65.0 MHz Horizontal 48.36 Negative
Vertical 60.00 Negative
VESA 1024×768@70Hz 75.0 MHz Horizontal 56.48 Negative
Vertical 70.07 Negative
VESA 1024×768@75Hz 78.8 MHz Horizontal 60.02 Positive
Vertical 75.03 Positive
VESA 1024×768@85Hz 94.5 MHz Horizontal 68.68 Positive
Vertical 85.00 Positive
VESA 1152×864@75Hz 108.0 MHz Horizontal 67.50 Positive
Vertical 75.00 Positive
VESA 1280×960@60Hz 108.0 MHz Horizontal 60.00 Positive
Vertical 60.00 Positive
VESA 1280×1024@60Hz 108.0 MHz Horizontal 63.98 Positive
Vertical 60.02 Positive
VESA 1280×1024@75Hz 135.0 MHz Horizontal 79.98 Positive
Vertical 75.03 Positive
VESA 1280×1024@85Hz 
(S2411W) 157.5 MHzHorizontal 91.15 Positive
Vertical 85.03 Positive
VESA 1600×1200@60Hz 
(S2411W) 162.0 MHzHorizontal 75.00 Positive
Vertical 60.00 Positive
VESA 1600×1200@65Hz 
(S2411W) 175.0 MHzHorizontal 81.30 Positive
Vertical 65.00 Positive
VESA 1600×1200@70Hz 
(S2411W) 189.0 MHzHorizontal 87.50 Positive
Vertical 70.00 Positive
VESA 1600×1200@75Hz 
(S2411W) 202.5 MHzHorizontal 93.80 Positive
Vertical 75.00 Positive
VESA CVT 1680×1050 146.3 MHz
Horizontal 65.29 Negative Vertical 59.95 Positive
Attention
•  Display position may be deviated 
depending on the PC connected, 
which may require screen adjustment 
using Adjustment  menu.
•  If a signal other than those listed in  the table is input, adjust the screen 
using the Adjustment menu. However, 
screen display may still be incorrect 
even after the adjustment.
•  When interlace signals are used, the  screen cannot be displayed correctly 
even after screen adjustment using the 
Adjustment menu.
S2111W _U M _E N _v1 .3 .in dd   3 7S2111W_UM_EN_v1.3.indd   373/2 /2 007   6 :5 5:1 8 P M3/2/2007   6:55:18 PM 
						

							
38Chapter 5  Reference
VESA CVT RB (S2111W) 
1680×1050119.0 MHzHorizontal 64.67 Positive
Vertical 59.88 Negative
VESA CVT (S2411W) 
1920×1200 193.3 MHzHorizontal 74.56 Negative
Vertical 59.89 Positive
VESA CVT RB (S2411W) 
1920×1200 154.0 MHzHorizontal 74.04 Positive
Vertical 59.95 Negative
S 2111W _U M _E N _v1 .3 .in dd   3 8S2111W_UM_EN_v1.3.indd   383/2 /2 007   6 :5 5:1 8 P M3/2/2007   6:55:18 PM