Eizo Flexscan S2111w Users Manual

							
19Chapter 2  Settings and Adjustments
2-5  Screen Size Selection
● To change screen size [Screen Size]
The image with the resolution other than the recommended resolution is 
displayed in full screen automatically. You can change the screen size by using 
 from  menu.
Menu Function
Full (default setting) Displays an image in full screen. Images are distorted in 
some cases because the vertical rate is not equal to the 
horizontal rate.
Enlarged Displays an image in full screen. In some cases, a blank 
horizontal or vertical border appears to equalize the 
vertical rate and the horizontal rate.
Normal Displays images with the speci fi ed resolution.
Example: Image size 1280 x 1024 in case of S2411W
  (1920 x 1200)  (1500×1200)  (1280×1024)
   Full
(Default setting) Enlarged Normal
[Procedure]
(1)  Choose  from the Adjustment menu, and touch 
.
(2)  Choose  from the  menu, and touch 
.
The screen size setting window appears.
(3)  Select “Full,” “Enlarged,” or “Normal” with  or , and touch .
The screen size setting is completed.
●  To adjust brightness of non-display area [Border Intensity]
A border (black area with no image) around the image appears in the “\
Normal” 
or “Enlarged” mode.
Border
(1)  Choose  from the Adjustment menu, and touch .
(2)  Choose  from the  menu, and touch 
.
The  menu appears.
(3)  Adjust border intensity with  or , and touch .
The border intensity adjustment is completed.
S 2111W _U M _E N _v1 .3 .in dd   1 9S2111W_UM_EN_v1.3.indd   193/2 /2 007   6 :5 5:0 3 P M3/2/2007   6:55:03 PM 
						

							
20Chapter 2  Settings and Adjustments
2-6  Power Indicator/EIZO Logo Display Setting
● To turn off the Power indicator while a screen is displayed 
[Power Indicator]
This function enables to turn off the Power indicator (blue) while a screen is 
displayed.
(1)  Choose  from the Adjustment menu, and touch 
.
(2)  Choose  from the  menu, and touch 
.
The  menu appears.
(3)  Select “Disable” with  or , and touch .
The Power Indicator setting is completed.
●  To display EIZO logo [EIZO Logo Appearing Function]
When this unit is turned on, the EIZO logo appears at the center of the \
screen. 
Selection to display or not to display the logo is available with this f\
unction.
[Procedure]
(1) Touch 
 to power off the unit.
(2) Touch 
 again while touching .
The EIZO logo does not appear on the screen.
[Resetting]
(1) Touch 
 to power off the unit.
(2) Touch 
 again while touching .
The logo appears again.
2-7 Beeper Settings
●  To set the beeper [Beep]
Set the beeper on/off for operation tone of the switches, connection error, etc.
Sound type Conditions for beeping
Short beep •  When an item is selected with 
•  When a maximum or minimum value is set with  the control switches
• When 
 is touched.
Long beep •  When 
 is touched.
•  When registration is performed with 
Consecutive beeps •  When the monitor is not connected correctly •  When the PC is not turned on
•  When a frequency out of the speci fi ed range is 
received
Beep-beep once every 15 
seconds •  15 minutes before the power off time set by “Off 
Timer” (advance notice time)
(1)  Choose  from the Adjustment menu, and touch .
(2)  Choose  from the  menu, and touch 
.
The  menu appears.
(3)  Select On or Off with  or , and touch .
The beep setting is completed.
NOTE
•  The Power indicator lights up at  power on with the default setting.
NOTE
•  The logo appears with the default setting.
S2111W _U M _E N _v1 .3 .in dd   2 0S2111W_UM_EN_v1.3.indd   203/2 /2 007   6 :5 5:0 4 P M3/2/2007   6:55:04 PM 
						

							
21Chapter 2  Settings and Adjustments
NOTE
•  The display time of the FineContrast menu remains unchanged.
2-8 Locking Switches
● To lock operation [Adjustment Lock]
This function locks the switches to retain the status adjusted or set on\
ce.
Switches that can 
be locked •  (Enter switch) Adjustments/settings using 
Adjustment menu
• 
 (Auto Adjustment switch)
Switches that cannot 
be locked • 
 
/  FineContrast mode selection/adjustment using 
control switches
• 
  /  Brightness adjustment using control switches
• 
 (Input Signal Selection switch)
(1) Touch  to turn off the unit.
(2) Touch 
 again while touching .
The screen is displayed with the adjustment lock.
[Unlocking]
(1) Touch 
 to turn off the unit.
(2) Touch 
 again while touching .
The screen is displayed with the adjustment lock released.
2-9  Setting Adjustment Menu Display
●  To update menu settings [Menu Size/Menu Position/Menu 
Off Timer/Translucent]
Menu Size
Change the Adjustment menu size using the following procedure.
(1)  Choose  from the Adjustment menu, and touch 
.
(2)  Choose  from the  menu, and touch 
.
(3)  Choose  from the  menu, and touch 
.
The  menu appears.
(4)  Select “Enlarged” using  or , and touch .
The menu size setting is completed.
Menu Position
Adjust the menu position using the following procedure.
(1)  Choose  from the Adjustment menu, and touch 
.
(2)  Choose  from the  menu, and touch 
.
(3)  Choose  from the  menu, and touch 
.
The  menu appears.
(4)  Select a menu position with   /  /  / , and touch .
The menu position setting is completed.
Menu Off Timer
Set the menu display time using the following procedure.
(1)  Choose  from the Adjustment menu, and touch 
.
(2)  Choose  from the  menu, and touch 
.
(3)  Choose  from the  menu, and touch 
.
The  menu appears.
(4)  Select “Enable” with  or .
(5)  Choose an Off Time (15/30/45/60 seconds) with 
 or , and touch .
The menu off timer setting is completed.
S 2111W _U M _E N _v1 .3 .in dd   2 1S2111W_UM_EN_v1.3.indd   213/2 /2 007   6 :5 5:0 5 P M3/2/2007   6:55:05 PM 
						

							
22Chapter 2  Settings and Adjustments
Translucent
Set the transparency for menu display using the following procedure.
(1)  Choose  from the Adjustment menu, and touch 
.
(2)  Choose  from the  menu, and touch 
.
(3)  Choose  from the  menu, and touch 
.
The  menu appears.
(4)  Adjust the transparency for menu display with  or , and touch .
The transparency setting is completed.
2-10  Viewing Information/Setting Language
●  To check settings, usage time, etc. [Information]
This function allows you to check settings, model name, serial number, and 
usage time of the monitor.
(1)  Choose  from the Adjustment menu, and touch 
.
The  menu appears.
(2) Then, touch  to check settings, etc.
●  To set a language to be displayed [Language]
Select the Adjustment menu language.
Selectable languages
English/German/French/Spanish/Italian/Swedish/Japanese/Simpli fi ed Chinese/
Traditional Chinese
(1)  Choose  menu from the Adjustment menu, and touch 
.
The  menu appears.
(2)  Choose a language with   /  /  / , and touch .
The language setting is completed.
NOTE
•  The usage time is not always “0” 
when you purchase the monitor due 
to factory inspection.
S2111W _U M _E N _v1 .3 .in dd   2 2S2111W_UM_EN_v1.3.indd   223/2 /2 007   6 :5 5:0 6 P M3/2/2007   6:55:06 PM 
						

							
23Chapter 2  Settings and Adjustments
NOTE
•  For default settings, refer to “Main default settings (factory settings)” on 
page 32.2-11  Resumption of Default Setting
● To reset color adjustment [Reset]
The hue in the color mode currently set will revert to the default setti\
ngs (factory 
settings).
(1)  Choose  from the Adjustment menu, and touch 
.
(2)  Choose  from the  menu and touch 
.
The  menu appears.
(3)  Select  with  or , and touch .
The reset operation is completed.
●  To reset all settings [Reset]
Reset all adjustments/settings to the factory default settings.
(1)  Choose  from the Adjustment menu, and touch 
.
(2)  Choose  from the  menu, and touch 
.
The  menu appears.
(3)  Select  with  or , and touch .
The reset operation is completed.
S 2111W _U M _E N _v1 .3 .in dd   2 3S2111W_UM_EN_v1.3.indd   233/2 /2 007   6 :5 5:0 7 P M3/2/2007   6:55:07 PM 
						

							
24Chapter 3  Connecting Cables
3-1  Connecting Two PCs to the Monitor
Two PCs can be connected to the monitor through the two DVI-I connectors \
on 
the back of the monitor.
Connection examples
DVI-I connector (SIGNAL1) DVI-I connector 
(SIGNAL2)
SIGNAL1 SIGNAL2Example 1DigitalDVI Signal cable 
(supplied FD-C39)Signal cable 
(supplied FD-C16)D-sub mini 
15-pinAnalog
Example 2Analog
D-sub mini 
15-pin
Signal cable 
(FD-C16 option)Signal cable 
(supplied FD-C16)D-sub mini 
15-pinAnalog
Example 3Digital
DVI Signal Cable 
(FD-C39 option) Signal cable 
(supplied FD-C39)DVIDigtal
Selecting input signal
Input signal selection switch
Switch the input signal with . Input signal switches each time  is 
touched. When the signal is switched, the active signal type (Signal 1 or 2/
Analog or Digital) appears at the top right corner of the screen for tw\
o seconds.
Chapter 3  Connecting Cables
S 2111W _U M _E N _v1 .3 .in dd   2 4S2111W_UM_EN_v1.3.indd   243/2 /2 007   6 :5 5:0 7 P M3/2/2007   6:55:07 PM 
						

							
25Chapter 3  Connecting Cables
NOTE
• Power-saving functionWhen “1” or “2” is selected for 
, the monitor’s 
power-saving function works only 
when the two PCs are in the power-
saving mode.  
•  When only one PC is connected, the  input signal is detected automatically 
regardless of whether the input signal 
1 or 2 has priority.● To set priority of PC to be displayed [Input Priority]
When two PCs are connected, either one can be displayed preferentially. The 
monitor senses the input signal regularly. When the signal that is given priority 
with the  setting is input, signal input switches automa\
tically to 
the prior signal.
Priority setting Function
1
Signal 1, input from DVI-I connector The priority input setting functions in 
the following cases.
•  When the monitor is turned on
•  When the Signal 1 status changes 
even when Signal 2 is displayed
2
Signal 2, input from DVI-I connector The priority input setting functions in 
the following cases.
•  When the monitor is turned on
•  When the Signal 2 status changes 
even when Signal 1 is displayed
Manual The monitor does not detect the PC’s  signals automatically. Select an active 
input signal with 
.
[Input priority setting]
(1)  Choose  from the Adjustment menu, and touch 
.
(2)  Choose  from the  menu, and touch 
.
The  menu appears.
(3)  Select “1” or “2” or “Manual” with  or , and touch .
The Input Priority setting is completed.
3-2  Connecting Peripheral USB Devices
This monitor has a hub compatible with USB. Connected to a PC compatible\
 
with USB or another USB hub, this monitor functions as a USB hub allowin\
g 
connection to peripheral USB devices.
●  Required System Environment (1)  A PC equipped with a USB port or another USB hub connected to 
a USB compatible PC
(2)  Windows 2000/XP/Vista or Mac OS 8.5.1 or later
(3)  EIZO USB cable (MD-C93)
●  Connection Procedure (Setup of USB Function) (1)  Connect the monitor  fi rst to a PC using the signal cable, and run 
the PC.
(2)  Connect the supplied USB cable between the downstream USB  port of a USB compatible PC (or another USB hub) and the 
monitor’s upstream USB port.
(3)  When the USB function setup is completed, the monitor functions  as a USB hub allowing connection to various peripheral USB 
devices through its downstream USB ports.
UpstreamDownstream
  The USB function is set up automatically upon connection of the USB cabl\
e.
Attention
•  This monitor may not work depending on PC, OS or peripheral devices to be 
used.
For USB compatibility of peripheral 
devices, contact their manufactures.
•  If the monitor is in the power saving  mode, or if the monitor is connected 
to the power outlet with the monitor 
turned off, all the devices connected 
to the USB ports (upstream and 
downstream) work. Therefore, power 
consumption of the monitor varies 
with connected devices even in the 
power saving mode.
S2111W _U M _E N _v1 .3 .in dd   2 5S2111W_UM_EN_v1.3.indd   253/2 /2 007   6 :5 5:0 8 P M3/2/2007   6:55:08 PM 
						

							
26Chapter 4  Troubleshooting
Chapter 4  Troubleshooting
If a problem still remains after applying the suggested remedies, contac\
t your local dealer.
• No-picture problems → See No.1 - No.2.
• Imaging problems  → See No.3 - No.14.
• Other problems  → See No.15 - No.18.
• USB problems  → See No.19 - No.20.
Problems Possible cause and remedy
1.  
No picture
•  Power indicator does not light. •  Check whether the power cord is connected correctly.
• Touch 
•  Power indicator is lighting blue.
•  Power indicator is lighting yellow.• Check gain setting. 
•  Switch the input signal with 
.
•  Operate the mouse or keyboard.
•  Turn on the PC. 
2.  The message below appears. This message appears when the signal is not input 
correctly even when the monitor functions properly.
•  This message appears when no signal is input.
•  The message shown left may appear, because some  PCs do not output the signal soon after power-on.
•  Check whether the PC is turned on.
•  Check whether the signal cable is connected properly. 
•  Switch the input signal with 
.
•  The message below shows that the input signal is  out of the speci fi ed frequency range. (Such signal 
frequency is displayed in red.)
 Example:
•  Select an appropriate display mode using the graphics  board’s utility software. Refer to the manual of the 
graphics board for details.
3.   Display position is incorrect.
•  Adjust image position so that it is displayed properly  within the display area using the  adjustment.
•  If the problem persists, use the graphics board’s utility  software if available to change the display position.
4.  Screen image displayed is smaller or larger than  the actual screen image. •  Adjust the resolution using  so that the input 
signal resolution equals the resolution in the resolution 
adjustment menu.
5.  Vertical bars appear on the screen or a part of the  image is  fl ickering.
• Adjust using .
6.  Whole screen is  fl ickering or blurring.
• Adjust using .
S 2111W _U M _E N _v1 .3 .in dd   2 6S2111W_UM_EN_v1.3.indd   263/2 /2 007   6 :5 5:0 8 P M3/2/2007   6:55:08 PM 
						

							
27Chapter 4  Troubleshooting
Problems Possible cause and remedy
7.  Characters are blurred. •  Adjust using .
8.  Upper part of the screen is distorted as shown  below.                   
•  This is caused when both composite sync (X-OR) signal and separate vertical sync signal are input 
simultaneously. Select either composite signal or 
separate signal.
9.  The screen is too bright or too dark. •  Adjust . (The LCD monitor backlight has a 
fi xed life span. When the screen becomes dark or begins 
to  fl icker, contact your local dealer.)
10. Afterimages appear. •  Use a screen saver or off timer function for a long-time 
image display.
•  Afterimages are particular to LCD monitors. Avoid  displaying the same image for a long time.
11.  Green/red/blue/white dots or defective dots remain  on the screen. •  This is due to LCD panel characteristics and is not a 
failure.
12.  Interference patterns or  fi ngerprints remain on the 
screen. •  Leave the monitor with a white screen. The symptom 
may disappear.
13.  Noise appears on the screen. •  When entering the signals of analog input, select 1 to 4 
in  from the  menu to change the 
mode.
•  When entering the signals of HDCP system, the normal  images may not be displayed immediately.
•  When utilizing [Enhancer] function, the normal images  may not be displayed since the display gradation 
abnormality or noise may occur on the screen depending 
on the display pattern. 
14.  Characters are pigmentized. •  When [OutlineEnhancer] is set excessively, the 
characters on the screen may be affected to color.
15.  The [Smoothing] icon on the Adjustment menu  [Screen] cannot be selected. •  [Smoothing] is disabled when the screen is displayed in 
the following resolutions.
•  1680 × 1050 (S2111W)
•  1920 × 1200 (S2411W)
•  Select [Normal] during “Enlarged” mode.
16.  The Main menu of Adjustment menu does not start. •  Check for Adjustment Lock function. (Refer to page 21)
•  Check whether the FineContrast menu is running. (Refer 
to “Simple adjustment [FineContrast mode]” on page 14.)
17.  The FineContrast menu does not start. •  Check whether the Main menu of Adjustment menu is 
running. (Refer to “Advanced Adjustments [Adjustment 
menu]” on page 15.)
18. The 
 switch does not function. • The  switch does not function when digital signal is 
input. 
•  Check whether the buttons are locked.
19.  PC does not boot or connected peripheral devices  does not works •  Check whether the USB cable is connected correctly.
•  Change the USB port to another one. If the PC or 
peripheral devices works correctly by changing the USB 
port, contact your local dealer. (Refer to the manual of 
the PC for details.)
•  Please perform the followings to check the status. Reboot the PC.
Connect the PC and peripheral devices directly.
If the PC or peripheral devices works correctly without 
connecting each other via the monitor (working as a USB 
hub), please contact your local dealer. 
20.  USB function cannot be set up. •  Check whether the USB cable is connected correctly.
•  Check whether the PC and OS are USB compliant. (For 
USB compliance of the respective devices, consult their 
manufacturers.)
•  Check the PC’s BIOS setting for USB when using  Windows. (Refer to the manual of the PC for details.)
S2111W _U M _E N _v1 .3 .in dd   2 7S2111W_UM_EN_v1.3.indd   273/2 /2 007   6 :5 5:0 9 P M3/2/2007   6:55:09 PM 
						

							
28Chapter 5  Reference
 Chapter 5  Reference
5-1 Attaching an Arm
The stand can be removed and replaced with an arm (or another stand) t\
o be 
attached to the monitor. Use an arm or stand of EIZO option.
[Attaching]
1  Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down.
2  Remove the stand. (Prepare a screwdriver.)Unscrew the four screws securing the unit and the stand with the 
screwdriver.
3  Attach the monitor to the arm or stand.Secure the monitor to the arm or stand using the screws speci fi ed in the 
user’s manual of the arm or stand.
Arm
•  
Clearance between the screw holes when attach an arm or stand: 
In case of 100mm × 100mm
Arm
•   Clearance between the screw holes when attach an arm or stand: 
In case of 200mm × 100mm (Only for S2411W)
Attention
•  When attaching an arm or stand, 
follow the instructions of their user’s 
manual.
•  When using another manufacturer’s  arm or stand, con fi rm the following in 
advance and select one conforming to 
the VESA standard. Use M4 × 12 mm 
screws supplied with this monitor.
– Clearance between the screw holes:  100 mm × 100 mm 
200 mm × 100 mm (Only for 
S2411W)
– Thickness of plate: 2.6 mm
– Strong enough to support weight of  the monitor unit (except the stand) 
and attachments such as cables.
•  Attach an arm or stand to meet the  following tilt angles of the monitor.
– Up 60 degrees, down 45 degrees
(Horizontal display. Or, vertical 
display, 90 degrees clockwise in case 
of S2111W)
•  Connect the cables after attaching an  arm.
S2111W _U M _E N _v1 .3 .in dd   2 8S2111W_UM_EN_v1.3.indd   283/2 /2 007   6 :5 5:0 9 P M3/2/2007   6:55:09 PM