Eiki Projector Lc Xb33n User Manual

1

Installation
The preparation display will disappear 
after 30 seconds.
(See page 52 for Lamp control status.)
Lamp control status
Turning On the Projector
Connect the projector’s AC power cord into an AC 
outlet. The POWER indicator lights red. Open the Lens 
cap (see pages 9,59).
Press the POWER ON/SYAND-BY button on the top 
control or  on the remote control. The POWER indicator 
lights green and the cooling fans start to operate. The 
preparation display appears on the screen and the count...



TO MAINTAIN THE LIFE OF THE LAMP, ONCE 
YOU TURN THE PROJECTOR ON, WAIT AT 
LEAST FIVE MINUTES BEFORE TURNING IT 
OFF.
“Power off?” disappears after 4 seconds.
Turning Off the Projector
Press the POWER ON/STAND-BY button on the top 
control or on the remote control, and “Power off?” 
appears on the screen.
Press the POWER ON/STAND-BY button again to turn 
off the projector. The POWER indicator starts to blink 
red, and the cooling fans keep running. (You can select 
the level of fans’...

3

Basic OperationBasic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen 
Menu. For each adjustment and setting procedure, refer to 
the respective sections in this manual.
Use the Point◄► buttons to select a Menu icon. Use 
the Point ▲▼ buttons to select an item in the selected 
menu.
Press the SELECT button to show the item data. Use 
the Point ◄► buttons to adjust the values.
To close the On-Screen Menu, press the MENU button 
again.
Press the...



Menu Bar
PC System Menu
Image Adjust Menu
Used to adjust computer image 
[Contrast/Brightness/ Color 
temp./White balance (R/G/B)/
Sharpness/Gamma] (pp.36–37).
Setting Menu
Used to adjust 
the volume or 
mute the sound 
(p.26).
Image Select Menu
Used to select an 
image mode among 
Dynamic, Standard, Real, 
Blackboard(Green), and 
Image 1–4 (p.35).
For computer source
AV System Menu
Used to select 
system of selected 
video source (p.41).
Used to adjust picture image...

5

Basic OperationBasic Operation
Rotate the Zoom Lever to zoom in and out.  
Rotate the Focus Ring to adjust the focus of the image.  
Zoom and Focus Adjustment
If a projected picture still has keystone distortion after 
pressing the AUTO SETUP/CANCEL button on the top 
control or the AUTO SET/CANCEL button on the remote 
control, correct the image manually as follows:
Press the KEYSTONE button on the remote control. The 
Keystone dialog box appears. Use the Point ▲▼ buttons to 
correct keystone...

6

Sound Adjustment
1

Press the MENU button to display the On-Screen 
Menu. Use the Point ◄► buttons to move the red 
frame pointer to the Sound Menu icon.
Press the VOLUME+/– buttons on the top control or on the 
remote control to adjust the volume. The volume dialog box 
appears on the screen for a few seconds.
Press the MUTE button on the remote control to temporarily 
turn off the sound. To turn the sound back on, press the 
MUTE button again or press the VOLUME +/– buttons. The 
Mute...

7

Basic OperationBasic Operation
Remote Control Operation
Using the remote control for some frequently used operations is advisabl\
e. Just pressing one of the buttons 
enables you to make the desired operation quickly without calling up the\
 On-Screen Menu.
Press the COMPUTER, VIDEO, or NETWORK button on 
the remote control to select the input source. See pages 29-
30, 39-40 for details.
Refer to the owner’s manual “Network Set-up and 
Operation” for details about the network input....

8

Basic Operation
black out → the captured image → normal → • • • • •
Press the NO SHOW button on the remote control to black out 
the image. To restore to normal, press the NO SHOW button 
again or press any other button. When a projected image is 
captured and set as “User” in the Logo selection (see page 48), \
the screen changes each time you press the NO SHOW button 
as follows.
NO SHOw button
Press the P-TIMER button on the remote control. The P-Timer 
display “00:00” appears on the screen...

9

Basic Operation
Choose either Computer 1 (Analog) or Computer 2 by 
pressing the INPUT button on the top control or press the 
COMPUTER button on the remote control.
Before using these buttons, correct input source should be 
selected through Menu operation as described below.
Press the MENU button to display the On-Screen 
Menu. Use the Point ◄► buttons to move the red 
frame pointer to the Input Menu icon.
1Input Menu
Use the Point ▲▼ buttons to move the red arrow 
pointer to either Computer 1...

30

Computer Input
Choose Computer 1(Digital) by pressing the INPUT button 
on the top control or press the COMPUTER button on the 
remote control.
Before using these buttons, correct input source should be 
selected through Menu operation as described below.
Press the MENU button to display the On-Screen 
Menu. Use the Point ◄► buttons to move the red 
frame pointer to the Input Menu icon.
1
Input MenuUse the Point ▲▼ buttons to move the red arrow 
pointer to Computer 1 (Digital), and then press the...