Eiki Projector Lc Xb31 User Manual

Part Names and Functions
11
Part Names and Functions
Remote Control
q POWER ON/STAND-By  button 
  Turn the projector on or off. (p.18, 19)
w VIDEO button
  Select VIDEO input source. (p.3, 35)
e COMPUTER button
  Select COMPUTER input source. (p.3, 5, 36)
r MENU button
  Open or close the On-Screen Menu. (p0)
u D .ZOOM ed buttons
  Zoom in and out the images. (p.4, 34)
!4 AUTO PC button
  A u t o m a t i c a l l y  a d j u s t  t h e  c o m p u t e r  i m a g e  t o  i t s...

InstallationPart Names and Functions
1
To insure safe operation, please observe the following precautions:
 ● Use two () AA or LR6 type alkaline batteries.
 ●  Always replace batteries in sets.
 ●  Do not use a new battery with a used battery.
 ●  Avoid contact with water or liquid.
 ●  Do not expose the remote control to moisture or heat.
 ●  Do not drop the remote control.
 ●  If  the  battery  has  leaked  on  the  remote  control,  carefully  wipe  the  case  clean  and  install 
new...

13
InstallationPart Names and Functions
✔ Note:
  • The  brightness  in  the  room  has  a  great  influence  on  picture  quality.    It  is  recommended  to  limit 
ambient lighting in order to obtain the best image.
  • The values shown below are approximate and may vary from the actual sizes. 
Positioning the Projector
A
B
34.4' (10.5 m)
3.0' (7.0 m)
17.0' (5. m)
11.5' (3.5 m)
A : B  =  9 : 1(Inch Diagonal)
4.6' (1.4 m)
For  projector  positioning,  see  the  figures...

To the AC outlet.(200 - 240 V AC)
InstallationInstallation
14
This projector uses nominal input voltages of 100-10 V 
or 00-40  V  AC.    This  projector  automatically  selects 
the  correct  input  voltage.    It  is  designed  to  work  with single-phase power systems having a grounded neutral conductor.  To reduce the risk of electrical shock, do not plug into any other type of power system.Consult  your  authorized  dealer  or  service  station  if  you are not sure of the type of...

InstallationInstallation
15
Connecting to a Computer
Cables used for connection • VGA Cables (Mini D-sub 15 pin) (Only one cable is supplied.) • Audio Cables (Mini Plug: stereo)(*One cable is supplied; other cables are not supplied   with the projector.)
External Audio Equipment
VGA cable  
Audio cable (stereo)Audio cable  (stereo)
Monitor OutputorMonitor Input
Audio Output
COMPUTER/ COMPONENTAUDIO IN
AUDIO OUT (stereo)
Audio Input
Monitor Output
COMPUTER IN 1/ COMPONENT IN 
VGA cable 
This terminal is...

Installation
16
Connecting to Video Equipment
Cables used for connection• Video and Audio Cable (RCA x 3) • S-VIDEO Cable  • Audio Cable (Mini Plug: stereo)  ( Cables are not supplied with the projector.)
ONON
✔ Note: •   When  connecting  AUDIO  OUT  to  external  audio e q u i p m e n t ,  t h e  p r o j e c t o r ’ s  b u i l t - i n  s p e a k e r  i s disconnected.
 
Unplug  the  power  cords  of  both  the  projector a n d  e x t e r n a l  e q u i p m e n t  f r o m  t h e  A C  o u t l e t...

InstallationInstallation
17
Connecting to Component Video Equipment
Cables used for connection • Audio Cables (Mini Plug :stereo)  • Scart-VGA Cable  • Component Cable  • Component-VGA Cable  ( Cables are not supplied with the projector.)
External Audio Equipment
COMPUTER IN 1/COMPONENT IN   
COMPUTER/ COMPONENTAUDIO IN
Audio cable   (stereo)
Audio cable  (stereo)
Audio Input
Component Video Output(Y, Pb/Cb, Pr/Cr)RGB Scart 
1-pin OutputAudio Output
Scart-VGA cable  
Component-VGA cable  
AUDIO OUT...

Basic OperationBasic Operation
18
Connect  the  projector's AC  power  cord  into  an AC outlet.  The POWER indicator becomes red.
Press  the  POWER  ON/STAND-BY  button  on  the top  control  or  on  the  remote  control.    The  POWER indicator  becomes  green  and  the  cooling  fans  start to operate.  The preparation display appears on the screen and the count down starts.
2
3
1
4After  the  countdown,  the  input  source  that  was selected  the  last  time  and  the  Lamp  mode  status icon...

Basic Operation
19
P r e s s  t h e  P O W E R  O N / S TA N D - B Y  b u t t o n  o n the  top  control  or  on  the  remote  control,  and  a message "Power off?" appears on the screen.
Press  the  POWER  ON/STAND-BY  button  again 
to  turn  off  the  projector.The  POWER  indicator 
starts  to  blink  red,  and  it  continues  while  the 
cooling  fans  are  operating  for  about  90  seconds.  
(You  can  select  the  level  of  fan  quietness  and 
rotation speed.  See page 51.)   
At...

Basic OperationBasic Operation
20
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen Menu.    Refer  to  the  following  pages  regarding  each adjustment and setting procedures.
Press  the  Point 7  8  buttons  to  select  a  Menu  icon to  adjust  and  press  the  Point ed  buttons  to  select an item to adjust.
Press  the  SELECT  button  to  show  the  item  data.  To  adjust  the  data,  press  the  Point 7  8  buttons.  Refer to the following pages for each...