Eiki Projector Lc Xb23 User Manual

41
Display Blue back
Press the Point7 8buttons to switch On/Off.  When this
function is “On,” a blue image is displayed while the input
signal is not detected. 
Keystone
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
framed pointer to the Setting Menu icon.1
2
Language
The language used in the On-Screen Menu is available in
English, German, French, Italian, Spanish, Portuguese,
Dutch, Swedish, Finnish, Polish, Hungarian, Romanian,
Russian, Chinese,...

42
Setting
Capture
This function enables you to capture the image being
projected and use it for a start-up display or interval of
presentations.  
After capturing the projected image, go to the Logo
select function and set it to “User”.  Then the captured
image will be displayed when turning on the projector
next time or pressing the NO SHOW button.  (p24) 
To capture the image, select [Yes].  To cancel the
Capture function, select [No].  
✔Note:
• Before capturing an image, select Standard in the Image...

43
Logo PIN code lock Dialog Box
QuitPointer
Enter a Logo PIN code
Select a number by pressing the Point7 8buttons and
fix the number with the SELECT button.  The number
will change to ✳.  If you fixed an incorrect number,
move the pointer to Set or Clear once by pressing the
Point 
dbutton, then return to Logo PIN code.  Enter
the correct number again.
Repeat this step to complete entering a four-digit
number. 
When the four-digit number is fixed, the pointer will
automatically move to Set.  Press the...

44
Setting
Ceiling 
Rear  Ceiling
When this function is “On,” the picture will be top/bottom
and left/right reversed.  This function is used to project the
image from a ceiling mounting the  projector.
Rear
When this function is “On,” the picture will be left/right
reversed.  This function is used to project the image to a
rear projection screen.
Terminal
The COMPUTER IN 2/MONITOR OUT terminal on the back
of the projector is switchable for computer input or monitor
output.  (See page 9)  Select Computer...

45
Setting
On start
When this function is “On”, the projector will be
automatically turned on just by connecting the AC power
cord to a wall outlet.
✔Note:
Be sure to turn the projector off properly (see “Turning Off the 
Projector” on page 19).  If the projector is turned off in the incorrect
sequence, the On start function does not operate properly.
Setting
Lamp control
Remote control
This projector provides two different remote control codes;
the factory-set, initial code (Code 1) and the secondary...

46
Setting
Key lock
If the top control accidentally becomes locked and you
do not have the remote control nearby, disconnect the
AC power cord from the AC outlet, and then with
pressing the SELECT button, reinsert the AC power
cord.  This will cancel the top control lock.Key lock
Select Key lock.  Choose one
of the alternatives with the
Point edbuttons and select
[Yes] to activate it.
Security (Key lock and PIN code lock settings)
This function allows you to use Key lock and PIN code
lock function to set...

47
Setting
The PIN code can be changed to your desired four-digit
number.
Select PIN code change with the Point 
dbutton, and
press the SELECT button to display the New PIN code
input dialog box.  
Select a number with the Point
7 8buttons and fix the
number with the SELECT button. Repeat it to complete
entering a four-digit number.  When the four-digit
number is fixed, the pointer will automatically move to
Set.  Then press the SELECT button.  
To Change the PIN code 
Change the PIN code
Select PIN code...

48
This function is used to reset the lamp replacement
counter.  When replacing the projection lamp, reset the
lamp replacement counter by using this function.  See page
53 for operation.Lamp counter 
Factory default
This function returns all setting values except for the user
logo,  PIN code lock, Logo PIN code lock and the lamp
counter to the factory default settings.
Select Factory default and
this box will appear.  Select
[Yes] , and the next box will
appear. 
Factory default
Select [Yes] to
activate...

49
The WARNING indicator shows the state of the function which protects the projector.  Check the state of the
WARNING indicator and the POWER indicator to take proper maintenance. 
TOP CONTROL
Wa rn ing Indicator
The projector is shut down and the WARNING
indicator is blinking red.
When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down
to protect the inside of the projector.  The POWER indicator
is blinking while the projector is being cooled...

50
Maintenance and Cleaning
Turn off the projector, and disconnect the AC power
cord from the AC outlet.
Turn over the projector and remove the air filters by
pulling the latches upward.
1
2
Air filters prevent dust from accumulating on the optical elements inside the projector.  Should the air filters
become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat
build up and adversely affect the life of the projector.  Clean the air filters following the...