Eiki Projector Lc Xb23 User Manual

11
Part Names and Functions
Remote ControlPart Names and Functions
To ensure safe operation, please observe the following
precautions :
–  Do not bend, drop the remote control or expose the
remote control to moisture or heat.
–  For cleaning, use soft dry cloth.  Do not apply benzene,
thinner, splay or any chemical material.
t
e
!0
i
!4
r
!5
!3
qPOWER ON-OFF button 
Turn the projector on or off.  (p18, 19)
wVIDEO button
Select VIDEO input source.  (p23, 34)
eCOMPUTER button
Select COMPUTER input source....

12
Part Names and Functions
123
To insure safe operation, please observe the following precautions:
●Use (2) AA or LR6 type alkaline batteries.
●Always replace batteries in sets.
●Do not use a new battery with a used battery.
●Avoid contact with water or liquid.
●Do not expose the remote control to moisture or heat.
●Do not drop the remote control.
●If the battery has leaked on the remote control, carefully wipe the case clean and install new 
batteries.
● Risk of explosion if a battery is replaced by an...

13
✔Note:
• The brightness in the room has a great influence on picture quality.  
It is recommended to limit ambient lighting in order to obtain the best image.
• The values shown below are approximate and may vary from the actual sizes. 
Positioning the Projector
Installation
100150200300
250
166
126
83
40
 A
B
43.3 (13.2m)
23.9 (7.3m)
18.0 (5.5m)
11.8 (3.6m)
Max. Zoom
Min. Zoom
A : B  =  10 : 1
Screen Size
(W x H) mm
4 : 3 aspect ratio
Zoom (min)
40”
Zoom (max)
813 x 610
5.6 (1.7m)
4.6 (1.4m)
100”...

14
Installation
This projector uses nominal input voltages of 100-120 V or 200-240
V AC.  This projector automatically selects the correct input
voltage.  It is designed to work with single-phase power systems
having a grounded neutral conductor.  To reduce risk of electrical
shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of the type of power being supplied.
Connect the projector with all peripheral equipment before turning...

15
Installation
Connecting to a Computer
ON ON
S-VIDEO IN  
MONITOR  OUTCOMPUTER IN 2 / 
COMPUTER / COMPONENTAUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUTCOMPUTER  IN  1/ COMPONENT INUSBSERVICE PORT RESET
Cables used for connection 
• VGA Cables (Mini D-sub 15 pin) (Only one cable is supplied.) 
•USB Cable ✽
• Audio Cables (Mini Plug: stereo) ✽
(✽= Not supplied with this projector.)
External Audio Equipment
VGA cable   USB cable ✽
Audio cable
(stereo) ✽
Audio cable ✽
(stereo) Monitor Output
or...

16
S-VIDEO IN  
MONITOR  OUTCOMPUTER IN 2 / 
COMPUTER / COMPONENTAUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUTCOMPUTER  IN  1/ COMPONENT INUSBSERVICE PORT RESET
Installation
Connecting to Video Equipment
Cables used for connection  
• Video and Audio Cable (RCA x 3) ✽
• S-VIDEO Cable ✽
• Audio Cable (Mini Plug: stereo) ✽
(✽ = Not supplied with this projector.)
✔Note:
• When connecting AUDIO OUT to external audio equipment, the
projectors built-in speaker is disconnected.
• See p61 for ordering...

17
Installation
Connecting to Component Video Equipment
S-VIDEO IN  
MONITOR  OUTCOMPUTER IN 2 / 
COMPUTER / COMPONENTAUDIO  IN
R
VIDEO INL(MONO)
(VARIABLE)
AUDIO  OUTCOMPUTER  IN  1/ COMPONENT INUSBSERVICE PORT RESET
Cables used for connection
• Audio Cables (Mini Plug :stereo) ✽
• Scart-VGA Cable ✽
• Component Cable ✽
• Component-VGA Cable ✽
(✽= Not supplied with this projector.)  
✔Note:
• When connecting AUDIO OUT to external audio equipment, the
projectors built-in speaker is disconnected.
• See p61...

18
Connect the projectors AC power cord into an AC
outlet.  The POWER indicator will be red.
Press the POWER ON-OFF button on the top control
or on the remote control.  The POWER indicator will
become green and the cooling fans will start to
operate.  The count down will start. 
2
3
1
16
The count down display will disappear 
after 30 seconds.
4After the countdown, the input source that was
selected last and the Lamp mode status icon (see
page 45) will appear on the screen.
If the projector is locked...

19
Basic Operation
Press the POWER ON-OFF button on the top control
or on the remote control, and a message Power off?
will appear on the screen.  
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator will start to blink red,
and the cooling fans will keep operating.  (You can
select the level of fun quietness and rotation speed.
See page 48.)  At this time you can disconnect the AC
power cord even if the fans are still running.
1
2
TO MAINTAIN THE LIFE OF THE LAMP, ONCE
YOU...

20
Basic Operation
ON - OFF
POWERKEYSTONE
INPUTWARNINGLAMP REPLAMENU
- VOLUME+ VOLUME
SELECT
Top Control
Menu barPointer
(red framed ) Menu icon
Item data
Press the Point 7 8
buttons to adjust the
value.
SELECT
button
Pointer (red framed )
Press the Point edbuttons
to move the pointer.
Item
How to Operate the On-Screen Menu
MENU button
SELECT buttonPOINT button
(outer ring)
On-Screen Menu
Quit  
Exit this menu.
The projector can be adjusted or set via the On-Screen
Menu. Refer to the following pages...