Eiki Projector Lc Xb200 User Manual

51

Setting
Enter	a	Logo	PIN	code
Use	the	Point	ed buttons	to	enter	a	number.	Press	the	
Point	8	button	to	fix	the	number	and	move	the	red	frame	
pointer	to	the	next	box.	The	number	changes	to	“✳”.	If	
you	fixed	an	incorrect	number,	use	the	Point	7	button	to	
move	the	pointer	to	the	number	you	want	to	correct,	and	
then	enter	the	correct	number.
Repeat	this	step	to	complete	entering	a	four-digit	
number.
After	entering	 the	four-digit	 number,	move	the	pointer	 to	
Set.	Press	 the	SELECT 	button	 so...

5

Setting
Ceiling	
Rear	
Ceiling
When	this 	function 	is 	set 	to 	On,	 the 	picture 	will 	be 	top/
bottom 	and 	left/right 	reversed. 	This 	function 	is 	used 	to	
project	the	image	from	a	ceiling-mounted	projector.
Rear
When	 this	function	 is	set	 to	On,	the	 picture	 will	be	left/right	
reversed. 	This 	function 	is 	used 	to 	project 	the 	image 	from	
rear	of	the	screen.
Closed	Caption
Closed caption   more...
Closed	Caption
Closed	Caption	is	a	function	that	displays	the	audio	portion
of	a...

5

Setting
Power	management
Time	left	before	Lamp	is	off.
Power	management
For	reducing	power	consumption	as	well	as	maintaining	
the	lamp	life,	the	Power	management	function	turns	off	the	
projection	lamp	when	the	projector	is	not	operated	for	a	
certain	period.
Select	one	of	the	following	options:
Ready	...............	 When	the	lamp	has	been	fully	cooled	
down,	the	POWER	indicator	changes	
to	green	blinking.	In	this	condition,	
the	projection	lamp	will	be	turned	on	if	
the	input	signal	is...

54

Setting
This	function	allows	you	to	change	brightness	of	the	
screen.
Normal	......	Normal	brightness	
Eco	............	Lower	brightness	reduces	the	lamp	
power	consumption	and	extends	the	
lamp	life.
Lamp	control	
Lamp	life	control
Lamp	control
Select	the	lamp	operation	when	the	total	lighting	time	of	a	
lamp	exceeds	the	recommended	total	hours	of	use.
Mode	1	 ..............	The	lamp	can	be	turned	on	even	after	
exceeding	the	recommended	total	
hours	of	use.
Mode		..............	The	lamp	can...

55

Remote	control
Setting
✔	Note:
•	When	different	codes	are	set	on	the	projector	and	on	the	remote	control,	any	operation	cannot	be	made.	In	that	
			case,	switch	the	code	on	the	remote	control	to	fit	the	code	on	the	projector.
•	If	the	batteries	are	removed	from	the	remote	control	for	a	long	period	of	time,	the	remote	control	code	will	be	reset.
Remote	control
The	eight	 different	 remote	control	codes	(Code	 1–Code	 8)	
are	assigned 	to 	the 	projector; 	the 	factory-set, 	initial 	code	
(Code	1)...

56

Setting
Key	lock
Key	lockSecurity	(Key	lock	and	PIN	code	lock)
PIN	code	lock
This	function	locks	the	top	control	and	remote	control	
buttons	to	prevent	operation	by	unauthorized	persons.
Select	Key	lock	and	then	press	the	SELECT	button,	and	
select	the	desired	item	by	pressing	the	Point	ed	buttons.
	.....	Unlocked.
	.....	Lock	the	operation	of	the	top	control.	To	
unlock,	use	the	remote	control.
	.....	Lock	the	operation	of	the	remote	control.				
To	unlock,	use	the	top	control.
If	the	top	control...

57

Setting
Use	the	Point	ed	buttons	to	select	Off、On1	or	On,	
and	then	press	the	SELECT	button	to	make	a	choice.
Change	the	PIN	code	lock	setting
Enter	a	PIN	code
Use	the	Point	ed	buttons	to	enter	a	number.	Press	the	
Point	8	button	to	fix	the	number	and	move	the	red	frame	
pointer	to	the	next	box.	The	number	changes	to	“✳”.	If	
you	fixed	an	incorrect	number,	use	the	Point	7	button	to	
move	the	pointer	to	the	number	you	want	to	correct,	and	
then	enter	the	correct	number.
Repeat	this	step	to...

58

This	function 	provides 	the 	following 	options 	in 	the 	cooling	
fans’ 	operation	when	the	projector	is	turned	off	(p.22).
	L1	......	Normal	operation
	L	......	Slower	 and	lower-sound	 than	the	normal	 operation	
(L1),	but 	it 	takes 	more 	time 	to 	cool 	the 	projector	
down.
Fan
Setting
This	projector	provides	Fan	control	function	in	the	Setting	
menu.
Choose	the	running	speed	of	cooling	fans	from	the	following	
options	according	to	the	ground	elevation	under	which	you	
use	the...

59

Setting
Factory	default
This	function	returns	all	setting	values	except	for	the	User	
logo,	PIN	code	lock,	Logo	PIN	code	lock,	Lamp	counter	
and	Filter	counter	to	the	factory	default	settings.
Factory	default
warning	log
This	function	records	anomalous	operations	while	the	
projector	is	in	operation	and	use	it	when	diagnosing	faults.	
Up	to	10	warning	logs	are	displayed	with	the	latest	warning	
message	at	the	top	of	the	list,	followed	by	previous	warning	
messages	in	chronological	order.	
✔ Note:...

60

Input	Source	Information	Display
The	Information	Menu	is	used	for	checking	the	status	of	the	image	signal	being	projected	and	the	operation	of	the	projector.
H-sync	freq .
V-sync	freq .
Lamp	counter
Information	Menu
The	horizontal	frequency	of	the	input	signal	is	displayed	in	
KHz,	or	-	-	-	-	-	when	no	signal.
The	vertical	frequency	of	the	input	signal	is	displayed	in	Hz,	
or	-	-	-	-	-		when	no	signal.	Numbers	of	Hz	doubles	when	
during	Interlace.
The	cumulative	lamp	operating	time	is	displayed....