Eiki Projector Lc Wul100a User Manual

							Setting
Setting Menu
Press the MENU button to display the On-Screen Menu.  Press the Point ▲▼ buttons to select Setting and press the Point ► or the SELECT button to access the submenu items.
1
2Use the Point ▲▼ buttons to select the desired item and then press the Point ► or the SELECT button to access the selected item.
This projector has a Setting menu that allows you to set up the other various functions described below.
3Use the Point ▲▼ buttons to select the desired item and then press the SELECT button.
The language used in the On-Screen Menu is available in English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Russian, Chinese, Korean and Japanese.
Language
Position
This function is used to change the position of the On-Screen Menu. Select Position and press the SELECT button.
The Position changes each time you press the SELECT button as follows.the center   the bottom left  the bottom right  the top left   the top right   the center  .....
This function detects the input signal automatically. When a signal is found, the search will stop. Use the Point ▲▼ buttons to select one of the following options.
Mode 1...... Input search will not work.Mode 2......  Input search works under the following situation:      –  When pressing the INPUT button on the side control or the remote control.Mode 3......  Input search works under the following situation:        – When turning on the projector by pressing the ON/STAND-BY button on the side control or pressing the ON button on the remote control.      –  When pressing the INPUT button on the remote control or on the side control.      – When no signal is detected.
Note:
	•	 While	Input button	is	set	to	Mode 3,	and	no	signal	is	detected,	if	the	Shutter	or	Freeze	function	is	active,	cancel	it	to	activate	the	Input	search.
	•	Only	the	last	selected	input	source	can	be	detected.
	•	If	the	INPUT,	INPUT	1,	INPUT	2,	INPUT	3,	ON	/	STAND-BY 	or	MENU	button	is	pressed	during	Input	search	is	in	progress,	Input	search	will	stop	and	go	back	to	the	previous	input	signal.
Setting
Language
Menu 
Input button
Menu size
This function is used to change the display size of the On-Screen Menu. Select Menu size and press the SELECT button.
     Normal… Display the On-Screen Menu on the screen in its normal size.     Double… Display the On-Screen Menu on the screen in its double normal size.
Note:
When	the	4:3	function	 is	selected	 in	Screen	 aspect,	Double	is	 not	 available;	it	will	 be	forced	 to	return	 to	Normal	in	Menu	size.
Position
51 
						

							This function decides whether to display On-Screen Displays.
 On .........................  Show all the On-Screen displays. Use this function when you want to project images after the lamp becomes bright enough. The factory default setting is in this option. Countdown Off ....  Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off  ........................ Hide the On-Screen Displays except:  ● On-Screen Menu  ● Power off? (p.24)  ● No signal for Power management.      (p.59)  ● Please wait  . . .  ●  White Arrows for panning mode (p.42)   ● P-timer  ● Simple mode  ● Video delay control  ● Picture in Picture  ● Corner pattern  ● Service
Setting
Select the background screen for when no input signal is detected. Press the Point ▲▼ buttons to switch among each option.
 Blue……Project a blue background.
 User……Project an image captured in the Logo setting.
                It is invalid when there is no image.
 Black……Project a black background.
Logo select
This function allows you to customize the screen logo with Logo select, capture, Logo PIN code lock and Logo PIN code change functions.
Note:
	 		When	On	is	selected	in	the	Logo	PIN	code	lock	function,	Logo select,	Capture	and	Logo PIN code change	cannot	be	selected.
Logo select
This function decides on the starting-up display from among following options.  Off ......... Show the countdown display only. User .......  Show the image you capture.  Default .. Show the factory-set logo. 
Display
Background
Logo (Logo and Logo PIN code lock settings)
52 
						

							Setting
Capture
Capture
This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations.
Select Capture and press the SELECT button.  A confirmation box appears and select ye s to capture the projected image.
After capturing the projected image, go to the Logo select function and set it to User. Then the captured image will be displayed the next time you turn on the projector.
To cancel the capture function, select ye s in the "Quit?" confirmation box.
Note:
	 •	Before	capturing	an	image,	select	Standard	in	the	Image	Select	Menu	to	capture	a	proper	image	(pp.40,	46).	 •	A	signal	from	a	computer	can	be	captured	up	to	WUXGA 	(1920	x	1200).	 •	When	capturing	the	image	that	has	been	adjusted	by	the	Keystone	function,	the	adjusted	data	is	automatically	reset	and	the	projector	captures	an	image	without	keystone	correction.		 •	When	Logo  PIN  code  lock	is	 set	 to	On,	Capture cannot	be	selected.				 •	When	starting	to	capture	a	new	image,	the	previously	stored	image	is	cleared	even	if	you	cancel	the	capturing.		•	When	there	is	no	captured	image	or	it	is	interrupted	while	capturing	an	image,	User	can	not	be	selected,	you	can	only	switch	between	Default	and	Off.		•	Capture	function	is	not	available	when	the	Picture	in	Picture	function	is	set	to	User 1-5.
Logo PIN code lock
This function prevents an unauthorized person from changing the screen logo.
 On .......... 
The screen logo cannot be changed without a Logo PIN code. Off  .........The screen logo can be changed freely from the Logo Menu (p.52).
If you want to change the Logo PIN code lock setting, press the SELECT button and the Logo PIN code dialog box appears. Enter a Logo PIN code by following the steps below. The initial Logo PIN code is set to "4321" at the factory.
Logo PIN code lock
53 
						

							Setting
Enter a Logo PIN code
When using side controlUse the Point ▲▼ buttons on the side control to select a number. Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to . If you fix an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number.
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to “Set”. Press the SELECT button so that you can start to operate the projector.
When using remote controlPress the Number buttons on the remote control to enter a number (p.14). When you complete entering a four-digit number, the pointer moves to “Set”. Press the SELECT button so that you can start to operate the projector.
If  you  enter  an  incorrect  Logo  PIN  code, Logo  PIN  code and the number () will turn red for a moment. Enter the correct Logo PIN code all over again.
Use the Point ▲▼ buttons to switch On or Off, and then press the SELECT button to close the dialog box.
Change the Logo PIN code lock setting
Enter a Logo PIN code
After a correct Logo PIN code is entered, the following dialog box appears.
CAUTION:
WHEN yOU HAVE CHANGED THE LOGO PIN CODE, WRITE DOWN THE NEW PIN CODE IN COLUMN OF THE LOGO PIN CODE NO . MEMO ON PAGE 87, AND KEEP IT SECUREL y . SHOULD THE LOGO PIN CODE BE LOST OR FORGOTTEN, THE LOGO PIN CODE SETTING CAN NO LONGER BE CHANGED .
Change the Logo PIN code lock setting
Logo PIN code change
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit number. Press the SELECT button to select Logo PIN code change. Current logo PIN code dialog box appears, use the Point ▲▼ buttons to enter the correct code. The New Logo PIN code input dialog box appears. Set a new Logo PIN code, confirmation box appears, choose Yes to set the new Logo PIN code.
Be sure to note the new Logo PIN code and keep it on hand. If you lost the number, you could no longer change the Logo PIN code setting. 
Use the Point ▲▼ buttons on the side control or Number buttons on the remote control to enter a number. 
54 
						

							Change the Logo PIN code lock setting
Setting
Picture in Picture
Picture in Picture
 
Show the selected mode (Off/User 1-5) and its status (Stored /Free/ Adj .). User 1 and User 2 have stored default values. See page 30 for details.
  User setting
P in P:   Provide the images of Main picture and Sub picture at the ratio of Screen aspect in the Screen Menu. P by P:  Provide the images of Main picture and Sub picture at the ratio of 4:3.
  P in P/P by P
Selected Mode
Status (Stored /Free/ Adj .) of the selected mode.
  Main picture / Sub picture
Input……Select an input from Input 1-3. 
Source…  
Select an input source. The display varies depending on the selected input.
Size………  Select the display size. Main picture can be changed between 10 and 100%, and Sub picture can be changed between 10 to 50% in increments of 10%. When P by P is selected in Mode, the projection size is fixed to 50%.
Position…  Press the SELECT button at Position and the display position setting screen appears.
Use the Point ▲▼◄► buttons to adjust the display position of active frame indicated in white. The frame will disappear after 10 seconds or when the SELECT button is pressed.
Position Menu
Active frame
(White)
Center line
display
Selecting the Main picture or Sub pictureDuring Picture in Picture mode, and being undisplayed On Screen Menu, press the SELECT button to select Main or Sub picture. (A red frame will be displayed on the selected picture.)
Switching Input and SourceWhen selecting Main picture or Sub picture, input and source can be set by pressing the INPUT button on the side control or INPUT 1/2/3 button on the remote control. Operation on the On Screen Menu is not necessary.
Note:
 •	The	Picture	in	Picture	function	is	not	available	depending	on	the	input	signals	and	the	selected	input	terminals.	See	List of Picture in Picture	for	details.	(p.89)
 •	When	the	input	signal(s)	is/are	incompatible,	X	mark	will	be	displayed	for	10	seconds	on	the	Main/Sub	picture.
This function is used to project two images simultaneously by placing a separate small sub screen within or next to the main screen.Use the Point ▲▼ buttons to select Picture in Picture and then press the SELECT button to display a dialog box. You can also display the dialog box by pressing and holding the PIP button on the remote control for more than 3 seconds.Only the sound from the source of Main picture is valid, while the source of Sub picture cannot output the sound. ( In P in P, the larger picture is main picture, and the smaller one is sub picture; in P by P, the left picture is main picture, and the right one is sub picture.)
Note:
 	 When	PIP 	is	selected,	screen	is	not	available.
55 
						

							HDMI setup
Set the Frame Lock to Main picture or Sub picture.
Frame lock
Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at yes.
Reset
Setting
To store the adjusted data .
Stored data
Vacant
Return to Picture in Picture menu.
This function is only used for HDMI input source.
Image
Select Normal or Enhanced to match the video range setting of your HDMI Digital RGB equipment.
Sound
HDMI:        When using the HDMI cable, select HDMI. Both video and audio are transferred and you need not to connect any additional cables for audio. 
AUDIO 1:  When using the DVI-HDMI cable, select AUDIO 1 and connect the audio cable to AUDIO 1 terminal.
The names for the output setting of Digital RGB vary from equipment to equipment. For details, refer to the owner’s manual of your Digital RGB equipment.
When the black parts of the image are destroyed or standout, please switch to Normal or Enhanced, and then switch the output type of the HDMI Digital RGB output equipment.
HDMI setup
Mode free
Store
Delete the data stored in the Mode and return to Free. Use the Point ▲▼ buttons to select Mode free and press the SELECT button to show the Where to free? dialog box. Move the highlight to one of the mode (User 1 - 5) which you want to delete and press the SELECT button. Then the confirmation box appears. To delete, select y es. 
Store the adjusted data in the User 1-5. Use the Point ▲▼ buttons to select Store and press the SELECT button to show the Where to store? dialog box. Move the highlight to one of the mode (User 1 - 5) which you want to store and press the SELECT button. Then the confirmation box appears. To store adjusted data, select yes. 
56 
						

							This function allows you to change brightness of the screen.
Lamp control
Lamp control
Select the lamp operation when the total lighting time of a lamp exceeds the recommended total hours of use.
     Mode 1 .......   The lamp can be turned on even after exceeding the recommended total hours of use.     Mode 2 .......   The lamp can be turned on even after exceeding the recommended total hours of use. But the projector turns off automatically after 3 minutes.
Lamp life control
Note:
•   	
Lamp	mode	cannot	be	changed	for	a	while	after	turning	on	the	projector.	Lamp	needs	some	time	to	stabilize	after	the	power	is	turned	on.	Stored	lamp	mode	will	be	active	after	the	lamp	is	stabilized.•    If	Mode 2 has	been	selected	and	the	projection	lamp	exceeds	the	recommended	total	hours	of	use,	the	replacement	icon	will	be	displayed	at	the	time	of	power-on.				Then	the	projector	will	turn	off	after	3	minutes.
    The Lamp replacement icon will not appear when the Display function is set to Off (p.52), during Freeze (p.30), or Shutter (p.27).
Lamp replacement icon
Setting
Auto .... Brightness according to the input signal. Normal . . Normal brightness. Eco 1 ...  Lower brightness and decrease of fan speed. Lower brightness reduces the lamp power consumption and extends the lamp life.Eco 2 ...  Lower brightness and increase of fan speed. Lower brightness reduces the lamp power consumption and extends the lamp life. It is recommended to use Eco 2 when using the projector continuously over a long period of time. The fan noise becomes louder in Eco 2 than in Eco 1. Select the suitable mode for the operating environment. 
Lamp control 
Note:
	 The	fan	noise	becomes	louder	in	Eco	2	than	in	Eco	1.			Select	the	suitable	mode	for	the	operating	environment.
57 
						

							Choose the running speed of cooling fans from the following options. Normal . . Operate in this mode under normal conditions. Max ........  Use this mode when you want to increase the cooling effect when operating the projector in high ambient temperature environment. Fan noise is louder than Normal. 
Setting
Simple mode buttons
Only these buttons are active when the simple mode is set to On. [ON, STAND-BY, SHUTTER, INPUT, MENU, AUTO PC, SCREEN, ▲, ▼ (MUTE), ◄ (VOLUME-), ► (VOLUME+), SELECT (Mouse Pointer included), L-CLICK, R-CLICK, P-TIMER, POINTER, PIP, ON-OFF switch] Number buttons (p.14) also become active only when setting the remote control codes numbers or entering the PIN code numbers (pp. 54, 62).
Filter control
This function decides whether to activate the simple mode.
 Off ... Simple mode function is off. On.... Only the simple mode buttons are active.
You can replace the filter with this function. Press the SELECT button at Filter control to display a confirmation box. To replace, press the SELECT button at ye s and the electrically operated filter starts to scroll.
Note:		•		 Filter	replacement	icon	and Please wait... message	appear	on	the	screen	when	the	filter	is	being	scrolled.		•		The	filter	cannot	be	rewound.		•		When	the	filter	is	replaced,	the	total	accumulated	time	of	the	filter	use	is	automatically	set	to	0.
A confirmation box appears and then select ye s.
The eight different remote control codes (Code 1- Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). The same code should be set on both the projector and the remote control. For example, operating the projector in Code 7, the remote control code also must be switched to Code 7.
 To change the code for the projector: Select a remote control code in this Setting Menu.
 To change the code for the remote control:    Press and hold the MENU button and a number button (1-8) on the remote control for more than five seconds to switch among the codes. See “Remote Control Code” on page 16.
Note:
•	When	different	codes	are	set	on	the	projector	and	on	the	remote	control,	no	operation	can	be	made.	In	that	case,	switch	the	code	on	the	remote	control	to	fit	the	code	on	the	projector.
Filter control
Fan control
Simple mode
Remote control
   
Note:
	
Warning	 icon	and	Simple  mode  :  On	message	 appear	on	the	 screen	 for	about 	4	 seconds 	when	 press	the 	button	which	is	not	the	simple	mode	button.
58 
						

							Note:
	 •	Factory	default	is	Ready: 5 Min.	 •		
When	the	shutter	is	closed	while	the	Power	management	function	is	working,	the	Power	management	function	is	released.
Setting
Select a location of the infrared remote receiver of the remote control. See “Remote Control Receivers and Operating Range” on page 15 for details.
 All.......................Activate all of the receivers.
 Front & Top.......Activate both the front and top receivers.
 Top & Back........Activate both the top and back receivers.
 Front & Back.....  Activate both the front and back receivers.
 Front..................Activate only the front receiver.
 To p.....................Activate only the top receiver.
 Back...................Activate only the back receiver.
No  signal
4 : 50
Timer left before Lamp is off.
Power management
For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not operated for a certain period.Select one of the following options:
 Ready ..............  When the lamp has been fully cooled down, the POWER indicator changes to green blinking. In this condition, the projection lamp will be turned on if the input signal is reconnected or any button on the side control or remote control is pressed.  Shut down ......  When the lamp has been fully cooled down, the power will be turned off.  Off  ................... Power management function is off. 
 Timer ...............  If the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with No signal appears. It starts the countdown until the lamp is turned off. Use the Point ▲▼ buttons to set the Timer (1~30 Min).
This function is available when operating the projector via network.
 Network....Supply the power to the network function even after turning off the projector. You can turn on/off the projector via network, modify network environment, and receive an e-mail about projector status while the projector is powered off.Eco............... Select Eco when you do not use the projector via network. The projector’s network function will stop when turning off the projector.
Refer to the owner’s manual of “Network Set-up and Operation”.
Note:
•	Factory	default	is	Network.
•	 	
When	selecting	Network,	the	cooling	fans	may	be	running	depending	on	the	temperature	inside	the	projector	even	if	the	projector	is	turned	off.
•		
When	Eco	is	selected	and	the	projector	is	in	Stand-by,	the	communication	of	RS-232C	serial	port	is	not	available.
RC sensor
Power management
Standby mode
59 
						

							Setting
When this function is set to On, the projector will be automatically turned on just by connecting the AC power cord to the wall outlet.
Note:
Be	sure	to	turn	off	the	projector	properly	(see	“Turning	Off	the	Projector”	on	page	24).	If	the	projector	is	turned	off	in	the	incorrect	sequence,	the	Direct	on	function	does	not	work	properly.
You can emphasize a part of the projected image with this function. Use the Point ▲▼ buttons to select a pattern of the Pointer (Dot, Arrow or Finger). (p.32)
This function allows you to change the presentation of the P-timer and execute it.
Select one of the following options: Count up .........  The P-timer display 000:00 appears on the screen and the count starts (000:00–180:00) 
 Count down ....  The time set in the Timer setting appears on the screen and the countdown starts.
 Timer ...............  Use the Point ▲▼ buttons to set the Timer (1–180 Min). Only set to Count down, Timer is active. Factory default value is 10 Min.
 Start  ................ It executes the count up or count down function. Press the SELECT button at Start, Start changes to Stop in the Screen Menu.  At that time, press the SELECT button at Stop to stop Count up or Count down,  and Stop changes to Restart in the Screen Menu. Press the SELECT button at Restart to resume Count up or Count down.
 Reset ...............  Reset the P-timer values.                              Press the SELECT button at Reset to return to the following value;Count up ........."000:00"Count down ... Timer that you set.
 Exit ..................  To exit the P-timer operation.
Stop or Cancel the P-timer via Remote Control
To stop the P-timer, press the P-TIMER button.To cancel the P-timer, press and hold the P-TIMER button for a few seconds.
P-timer
P-timer display.
Direct on
Pointer
P-timer
P-timer
60