Eiki Projector Lc Wul100a User Manual

Remote Control
POINT ▲▼◄►buttons
KEySTONE button
Basic Operation
If a projected picture still has keystone distortion after pressing the AUTO PC button on the remote control, correct the image manually as follows:Press the KEYSTONE button on the remote control to switch the Standard (for Vertical/Horizontal) /Corner correction adjustment. The Standard or Corner correction adjustment dialog box appears. Use the Point ▲▼◄► buttons to correct the Standard or Corner distortion. The Standard or Corner...

Note:   You	can	choose	the	pattern	of	Pointer	(Dot/Arrow/Finger)	in	the	Setting	Menu	(p.60)
You can move the Pointer of the projector with the remote control to emph\
asize a part of the projected image.  
Press the POINTER button to activate the Pointer function.1
2
3
MOUSE POINTER button
POINTER buttonTo cancel the Pointer function, press the POINTER button again or press any other button. 
Use the MOUSE POINTER button to move the Pointer. 
The remote control can be used as a wireless mouse for your...

The input source changes each time you press the INPUT button on the side control or the remote control as follows:
 Input 1→ Input 2→ Input 3 → ...
Before using the INPUT button on the side control or the remote control, you must select a cor\
rect input source by On-Screen Menu and the latest input source will be displ\
ayed.
Input Selection
Press the INPUT 1, INPUT 2, or INPUT 3 button on the remote control. The input source appears on the screen as you press each button. Select the connected input...

INPUT MENU
When your computer is connected to the INPUT 1 (ANALOG) terminal, select RGB (PC analog).
RGB(PC analog)
Note:
			Input	source	changes	if	the	INPUT	1	button	on	the	remote	control	is	pressed.
When connecting the computer output [5 BNC Type (Green, Blue, Red, Horiz. Sync, and Vert. Sync.)] from the computer to G, B, R, H/HV, and V jacks:
Input Selection
When your computer is connected to the INPUT 2 (5 BNC INPUT JACKS) terminal, select RGB.
RGB 
1
2
3
Press the MENU button to display the...

When the video input signal is connected to the Y-Pb/Cb-Pr/Cr jacks, select y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the VIDEO jack, select Video.
When the video input signal is connected to the S-VIDEO jack, select S-video.
When connecting to video equipment, select the type of Video source in the Source Select Menu. 
When the video input signal is connected to the Y-Pb/Cb-Pr/Cr jacks, select y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the VIDEO jack, select Video.
When...

Computer Input
PC System Menu
PC System Menu
1
2
PC system can also be selected manually.
The PC System Menu  Selected system is    displayed.
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button. 
Use the Point ▲▼ buttons to select System and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired system and then press the SELECT button.3
Systems in this dialog box can be...

Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Position H and Position V to conform to your computer. 
To store the adjusted parameters:
The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC SYSTEM Menu (p.36). See “Manual PC Adjustment” on pages 38-39.
Note:
	 •	Fine	sync,	Total	dots,	Position	H	and	Position	V		of	certain	computers	cannot	be	fully...

Some computers employ special signal formats which may not be tuned by M\
ulti-Scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those special signal formats. The projector has 10 independent memory areas to store those parameters \
manually adjusted. It allows you to recall the setting for a specific computer. 
Use  the  Point  ◄►  buttons  to  adjust  the  value, eliminating  a  flicker  from  the  image  displayed  (from  0 to 31).
Use the...

Computer Input
Note:
•		Display  area  (H/V)	cannot	 be	selected	 when	480i,	575i,	480p,	575p,	720p,	1035i,	1080i or  1080p	 is	selected	in	the	PC	System	Menu	(p.36).•		When	 input	computer	 signal	to	the	 projector,	 PC	adjust	function	will	become	available.
Vacant
This mode has stored parameters.
Values of Total dots, Position H, Position V, Display area H and Display area V.
Press the SELECT button to store the data.
Press the MENU button to close this dialog box.
Mode free
Store
To store the...

1
2
Normal picture level preset on the projector. 
Picture level with improved halftone for graphics.
User  preset  picture  adjustment  in  the  Image  adjust Menu. (pp.41-42)
Computer Input
Image select Menu
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image select and then press the Point ► or the SELECT button. The factory default setting is Standard.
Use the Point ▲▼ buttons to select the desired item and then press the SELECT button.
Image Level Selection...