Eiki Projector Lc Wul100a User Manual

The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWERgreenLAMP red
WARNINGTEMP.red
WARNINGFILTERorange
SHUTTER blue
 LAMPREPLACEorange
If the Filter counter reaches a time set in the timer setting, a Filter replacement icon (Fig.2) will appear on the screen and the WARNING FILTER indicator on the top panel will light up. Replace the filter as soon as possible. If the filter is out of scroll and the projector reaches a time set in the timer setting, Fig. 3 will appear on the...

ON-SCREEN DISPLAyRESOLUTIONH-Freq . (kHz)V-Freq .(Hz)
VGA 1640x48031.470 59.880 VGA 2720x40031.470 70.090 VGA 3640x40031.470 70.090 VGA 4640x48037.860 74.380 VGA 5640x48037.860 72.810 VGA 6640x48037.500 75.000 VGA 7640x48043.269 85.000 MAC LC13640x48034.970 66.600 MAC 13640x48035.000 66.670 480p640x48031.470 59.880 575p768x57531.250 50.000 575i768x576(Interlace)15.62550.000 480i640x480(Interlace)15.73460.000SVGA 1800x60035.156 56.250 SVGA 2800x60037.880 60.320 SVGA 3800x60046.875 75.000 SVGA...

ON-SCREEN DISPLAyRESOLUTIONH-Freq . (kHz)V-Freq .(Hz)
D-VGA640x48031.470 59.940 D-480p720x48031.470 59.880 D-575p720x57531.250 50.000 D-SVGA800x60037.879 60.320 D-XGA1024x76848.363 60.000 D-WXGA 11366x76848.360 60.000 D-WXGA 21360x76847.700 60.000 D-WXGA 31376x76848.360 60.000 D-WXGA 41360x76856.160 72.000 D-WXGA 51366x76846.500 50.000 D-WXGA 61280x76847.776 59.870 D-WXGA 71280x76860.289 74.893 D-WXGA 81280x76868.63384.837D-WXGA 91280x80049.600 60.050 D-WXGA 101280x80041.200 50.000 D-WXGA...

Appendix
Mechanical Information  Projector Type  Multi-media Projector  Dimensions (W x H x D)  LC-WUL100AL  : 19.27'' x 6.46'' x 14.61'' (489.5 mm x 164.0 mm x 371.1 mm)     LC-WUL100A    : 19.27'' x 6.46'' x 17.12'' (489.5 mm x 164.0 mm x 434.8 mm)  Net Weight   LC-WUL100AL  : 19.8 lbs (9.0 kg)     LC-WUL100A    : 21.6 lbs (9.8 kg)  Feet Adjustment  0˚ to 4˚        
Panel Resolution  LCD Panel System  0.76'' TFT Active Matrix type, 3 panels...

The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector for wide variety of uses.For installation and replacement of the lens, always contact the sales d\
ealer. The projector lens must be installed or replaced by well-trained sales or service engineers. Do not\
 attempt to install and replace the lens by yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector....

ANALOG/ ANALOG OUT (Mini D-sub 15 pin)
Appendix
Configurations of Terminals
512341096781514131112
CONTROL PORT CONNECTOR (D-sub 9 pin)
-----R X DT X D-----SG---------------
Serial12345678
Vcc- Data+ DataGround
1234
USB CONNECTOR (Series B)
-----9
RX –TX +TX –RX +234
5678
1
LAN TERMINAL
-----
---------------
13579111315171918161412108642
TMDS Dat a 2+  Input
Ground (TMDS Dat a 1)
Ground (TMDS Data 2)
TMDS Data 1+ InputTMDS Data 2- Input
TMDS Data 1- InputTMDS Dat a 0+ InputGround (TMDS Dat a 0)
1
5
2
43...

Write down the PIN code number in the column below and keep it with this \
manual securely. If you forgot or lost the number and unable to operate the projector, contact the service center. 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
* Should  the  four-digit  number be  changed,  the  factory  set number will be invalid.
Put the label below (supplied) on in a prominent place of the projector’s body while it is locked with a PIN code.
While the projector is locked with the PIN...

Appendix
Dimensions
Unit: inch (mm)
16.39

416.92

6.46(164.0)5.91(150.0)
19.27(489.5)
3.34(84.7)
6.67(169.5)14.61(371.1)
6.25(158.8)
5.91(150.0)
6.89(175.0)
2.95(75.0)1.18(30.0)
7.70(195.5)
3.78(96.0)
6.30(160.0)17.12(434.8)9.20(233.6)
4°
13.58(344.9)
3.31(84.0)
7.25(184.2)
3.80(96.6)
Screw Holes for Ceiling MountScrew: M6Depth: 0.393 (10.0)
88 

Appendix
This projector provides a function to control and monitor the projector'\
s operations by using the RS-232C serial port.
Connect a RS-232C serial cross cable to CONTROL PORT on the projector and serial port on the PC.  (See p.19)
Launch a communication software provided with PC and setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bpsParity check  : noneStop bit   : 1Flow control : noneData bit   : 8
Type the command for controlling the projector and then enter the...

The command is sent from PC to the projector with the format below;     'C' [Command] 'CR'       Command: two characters (refer to the command table below.
- The projector decodes the command and returns the 'ACK' with the format below;      'ACK'  'CR'
- When the projector can not decode the command, it returns with format below.      ‘?’  ‘CR’ 
Format
Appendix
CommandFunction
C00Turn the projector ON
C01Turn the projector OFF (immediately OFF)
C02Turn the...