Eiki Projector Lc Wul100 User Manual

							Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use a lens cleaning paper or commercially available air blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the lens.
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning cloth. When the cabinet is heavily soiled, use a small amount of mild detergent and finish with a soft dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the cabinet.
When the projector is not in use, put the projector in an appropriate carrying case to protect from dust and scratches.
Maintenance and Care
Cleaning the Projection Lens
Cleaning the Projector Cabinet
Do not use any flammable solvents or air sprays on the projector and in \
its vicinity. The explosion or fire hazard may occur even after the AC power cord is unplugged because the temperature inside the projector \
is extremely high due to the lamps. In addition, there is a risk that th\
e internal parts may be damaged not only by the flammable air spray but also by the cold air.
CAUTION
71 
						

							The WARNING indicators show the state of the function which protects the proj\
ector. Check the state of the WARNING indicators and the POWER indicator to take proper maintenance. 
The projector is shut down and the WARNING TEMP . indicator is blinking red .
When the temperature inside the projector reaches acertain level, the projector will be automatically shut down to protect the inside of the projector. The POWER indicator is blinking while the projector is being cooled down. When the projector has cooled down enough (to its normal operating temperature), it can be turned on again by pressing the ON/STAND-BY button.
Note:
  	The	WARNING	TEMP.	indicator	continues	to	blink	even	after	the	temperature	inside	the	projector	returns	to	normal.	When	the	projector	is	turned	on	again,	the	WARNING	TEMP.	indicator	stops	blinking.	
Then check the matters below:
–    Did you provide appropriate space for the projector to be ventilated? Check the installing condition to see if the air vents of the projector are not blocked.–   Has the projector been installed near an Air-Conditioning/ Heating Duct or Vent? Move the installation of the projector away from the duct or vent.–  Is the filter clean? Replace the filter with a new one.
The projector is shut down and the LAMP indicator is lighting and other indicators are blinking .
When the projector detects an abnormal condition, it will be automatically shut down to protect the inside of the projector and the LAMP indicator lights on and other indicators blink. In this case, unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the projector cannot be turned on and these indicators are still lighting and blinking, unplug the AC power cord and contact the service center.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK.
Top Panel
LAMP indicator lights on and other indicators blink .
Top Panel
WARNING TEMP  .blinking red
Maintenance and Care
Warning Indicators
72 
						

							Appendix
Before calling your dealer or service center for assistance, check the i\
tems below once again.
1. Make sure you have properly connected the projector to peripheral equipm\
ent as described on pages 19-21.2. Check the cable connection. Make sure that all computers, video equipmen\
t, and power cords are properly connected.3. Make sure that all power is switched on.4. If the projector still does not produce an image, restart your computer.5. If an image still does not appear, disconnect the projector from your computer and check your computer monitor’s display. A problem may be noticed with your graphics controller rather than with t\
he projector. (When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the projector. Turn on equipment in the order of the projector and computer.)6. If a problem still persists, check the following solutions.
Problem:Solutions
No power  .
– Plug the power cord of the projector into the AC outlet.–  Wait until the POWER indicator stops blinking to turn on the projector ag\
ain. (See page 23)–  Check the WARNING TEMP. indicator. If the WARNING TEMP. indicator is blinking, the projector cannot be turned on. (See page 72)– Unlock the Key lock function for the projector.  (See page 61)–  See if the filter cartridge is inserted.  (See page 67)– Check the projection lamp.  (See pages 69-70)
PIN code dialog box appears at start-up .–  
PIN code lock is being set. Enter a PIN code; the “1234” or number\
s you have set. (See pages 23, 61-62)
The initial display is not shown .– Make sure Off or Countdown Off is not chosen at Display function.   (See “Setting” section on page 52)
The initial display is not same with the default one .
– Make sure User or Off is not chosen at Logo select function.   (See “Setting” section on page 52)
When the projector is on and you press the input button, an icon other than the Lamp mode icon appears .
– That is the Filter warning icon. (See page 66)
An icon other than Input mode or Lamp mode icon appears .– That is the Lamp replacement icon or the Filter warning icon.  (See pag\
es 66,69)
No image .
– Check the connection between your computer or video equipment and t\
he projector.–  See if the input signal is correctly output from your computer. Some laptop computers may need to be changed the setting for monitor output when con\
nected to the projector. See your computer’s instruction manual for the setting.– It takes about 30 seconds to display an image after turning on the \
projector.– See if the selected system is corresponding with your computer or v\
ideo equipment.– Select correct input source once again through menu operation.  (S\
ee pages 33-35)–  Make sure the temperature is not out of Operating Temperature (41˚F–104˚F [5˚C–40˚C]).–  Make sure that the shutter is opened. (pp.27, 63)
 
appears on the screen
–  End of lamp life is approaching. Replace the lamp with a new one promptl\
y.  (See page 69)
Troubleshooting
73 
						

							Appendix
appears on the screen
–  Filter  is  out  of  scroll.  Replace  the  filter  cartridge  with  a  new  one  promptly.    (See pages 67-68)
The image is out of focus .
– Adjust the focus of the projector.– Check Projection Lens to see if it needs cleaning. Note:  Moving	the	projector	from	a	cool	temperature	location	to	a	warm	temperature	location	may	result	in	moisture	condensation	on	Projection	Lens.	In	such	cases,	leave	the	projector	OFF	and	wait	until	condensation	evaporates.–   Projecting  from  excessive  slant  angle  to  the  screen  may  cause  keystone  distortion and partial imperfect focus.
The image is not bright enough .
– Check if Contrast or Brightness is adjusted properly. (See pages 41, 47) – Check if Image level is selected properly. (See pages 40, 46)– Check the Lamp control function. ( See “Setting” section on \
page 57)–  Check the LAMP REPLACE indicator. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. (See page 69)
The color is strange .– Check the Input signal, color system, video system, or computer sys\
tem mode.– Adjust the Image Level properly. (See pages 40, 46)The image is Left/Right reversed .– Check the Ceiling / Rear function. (See pages 44, 50)
The image is Top/Bottom reversed .– Check the Ceiling function. (See pages 44, 50)
The image is distorted or runs off .– Check PC adjust Menu or Screen Menu and adjust them.
Auto PC adjustment function does not work.
–  Check the Input signal.  Auto PC Adjustment function cannot work when 480p, 575p, 720p, 480i, 575i, 1035i, 1080i or 1080p is selected or when the digital signal is input into HDMI or DVI-D terminal. See page 37. 
Some displays are not seen during the operation .– Check the Display function. (see page 52)
The setting does not remain after turning off power  .
–  
Make  sure  you  selected Store  after  adjusting  settings.  Some  settings  cannot  be stored if not registered with Store function.
Power management function does not work .
–  
Power  management  function  cannot  work  while  Freeze  function  is  running  or  the shutter is closed.
Image disappears automatically  .–  Check the power management function in the Setting. The power management is set to On at the factory.
Capture function does not work .
– Check the connection to see if there is signal.–  Capture  function  is  not  available  when  the  Picture  in  Picture  function  is  set  to User1-5.
Some menus cannot be selected .– Each of the Video Input and Computer Input has a limit on selectable menus.
No sound
– Check the audio cable connection from audio input source.– Adjust the audio source.– Press the Volume + button. ( See page 28)– Press the Mute button. (See page 28)– Is the image projected? You will hear the sound only when the image is projected.– Check the Build-in SP function. (See page 28)
74 
						

							Appendix
WARNING: High voltages are used to operate this projector . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector  or  the  service  center.  Specify  the  model  number  and  explain  about  the  problem.  We  will  advise you how to obtain service.
The shutter does not work .- Check "Protection" or "Release key" of the Shutter function. (See p.6\
3)
The power is turned off automatically .
–  
Power  management  function  runs  by  initial  setting.  Check  “Setting” section on page  59.–  When the filter cartridge replacement icon keeps appearing on the screen\
 at turning on the projector for some time and no action is taken to repl\
ace the filter cartridge, the projector will be automatically shut down in 3\
 minutes after turning on to protect the projector. (See pages 66, 81)–  Do not cover the ventilation slots on the projector. (See pages 4, 6)–  Projector may be used in high ambient temperature environment. Make sure the temperature is not out of Operating Temperature (41˚F–104˚F [5˚C–40˚C]). (See page 72)
you cannot operate with the side control .
–   If the side control is locked at "Key lock" under "Security" of Setting \
menu, the side control is not available. Please check “Setting” section \
on page 61.
The Remote Control does not work .
– Check the batteries.– Check if the RC sensor is set properly.  (See page 59)– Make sure no obstruction is between the projector and remote contro\
l.–  Make sure you are not too far from the projector when using the remote control. Maximum operating range is 16.4’ (5m). (See page 15)–  Make  sure  that  the  remote  control  code  conforms  to  the  projector’s  code. (See “SETTING” section on page 58.)– Unlock the Key lock function for the remote control.  (See page 61\
)–  Wireless remote control does not work when the remote control cable is connected to the  projector.  (See page 15)– Check if the ON/OFF switch on the remote control is set to “ON.”\
–  Make sure that the simple mode in the remote control function is set to Off (See page 58).
Wireless mouse function does not work .
–  Check the cable connection between the projector and your computer. (See pages 19, 32)– Check the mouse setting on your computer.– Turn on the projector before you turn on the computer.
Indicators blink or light .–  Check the status of the projector with referring to “Indicators and p\
rojector condition” on pages 79-81.
appears on the screen
– Your operation is invalid. Operate correctly.
Unable to unlock the Logo PIN code lock, Security key lock or Security PIN code lock .
–  
Contact  the  dealer  where  you've  purchased  the  projector  or  the  service center.
Forget the Logo PIN code or Security PIN code . 
–  
Contact  the  dealer  where  you've  purchased  the  projector  or  the  service center.
appears on the screen
–  
The  projector  detects  an  abnormal  condition.  Unplug  the  AC  power  cord  and contact the dealer where you purchased the projector or the service cent\
er.
75 
						

							Mode 10
InputRGB (PC analog)
Y, Pb/Cb,Pr/Cr
RGB (Scart)
HDMI
Network
Video
RGB
Video
Y, Pb/Cb,Pr/Cr
S-video
Input 3
Input
H-sync freq.V-sync freq.
Information
ScreenLanguageLamp status
Power management
Remote control
Note:
 	The	Menu	display	varies	depending	on	the	input	signal.
Appendix
Volume
MuteOn/Off
Sound0-63Built-in SP
PIN code lockKey lock
SERIAL NO.
Network will be displayed only when an optional Pj-to NetDirector is attached.
*
*
Input 1
Input 2
Lamp counterFilter counter
Simple mode
On/Off
System (1)Mode 1
 System displayed in the System Menu varies depending on the input signal.
SVGA 1SVGA 2SVGA 3
Image adjustContrastBrightness
Color temp.
Red
Gamma
Store
0–630–63
0–63
0–15
Image 1
Image 10
ResetYes/No
Sharpness0–31
GreenBlue0–630–63
MidLowXLow
AdjHigh
OffsetRed/Green/Blue
Image selectDynamic
RealImage 1
Image 10
PC adjustAuto PC adj.Fine sync.Total dotsPosition HPosition VCurrent modeClampDisplay area - HDisplay area - VResetMode freeStore
0–31
Yes/No
Mode 1
Mode 10
Menu Tree
Computer Input/HDMI Input/Video Input
Computer Input
Image adjust
Image select
PC adjust
Sound
Information
Input
Shutter management 
Standard
 SVGA1
IrisOn/Off
RGB (PC digital)
RGB (AV HDCP)
System
76 
						

							Note:
	 The	Menu	display	varies	depending	on	the	input	signal.
System (2)AutoPA LSECAMNTSCNTSC 4.43PAL-MPAL-N
System (3)Auto
1080i1035i720p575p480p575i480i
Image select
Cinema
Appendix
ScreenNormal
Wide(16:9)Full
Zoom
RearCeiling
On/OffOn/Off
Custom adj.H & VScale
Position
H / VOn/OffH / VCommonReset
Reset
Screen
Digital zoom +
Digital zoom -
Video Input
Image select
Screen
Image adjustContrastBrightness
Color temp.
Red
Gamma
Store
0–630–63
0–63
0–15
Image 1
Image 10
ResetYes/No
Sharpness0–31
GreenBlue0–630–63
MidLowXLow
AdjHigh
OffsetRed/Green/Blue
Image adjust
Color0–63Tint0–63
Noise reductionOff/OnProgressiveOff/On/Film
Custom
DynamicStandard
Image 1
Image 10
ScreenNormalFullWide(16:9)
Natural wide
Rear
Keystone
Ceiling
Corner correctionStandard
On/OffOn/Off
Custom adj.Scale
Position
H / VOn/OffH / VCommonReset
Reset
Custom
Screen aspect
Zoom
True
HDMI Input/Video Input
1080p
Default(16:10)/16:9/4:3
Corner patternStore
Natural
Screen aspectDefault(16:10)/16:9/4:3
IrisOn/Off
H & V
KeystoneCorner correctionStandard
Corner patternStore
77 
						

							Appendix
SettingLanguage
Fan control
Blue/User/Black
Yes/No
12 languages providedMenu
Lamp control
Filter control
All/Front&Top/Top&Back/Front&Back/Front/Top/Back
Normal/Max
Power management
Background
RC sensor
ReadyOff
Shut down1–30 Min
On/OffDirect onPointer
On/Countdown Off/OffDisplay
Remote Control
Dot/Arrow/Finger
Yes/No
Management
Remote controlProjector
5 - 480 Min
Code 1~Code 8
On/Off
Computer Input/HDMI Input/Video Input
Logo select
Off
User
CaptureYes/NoOff/OnLogo PIN code changeLogo PIN code lock
Default
Logo
Input buttonMode 1/Mode 2/Mode 3
Lamp life controlLamp controlAuto/Normal/Eco 1/Eco 2
Mode 1/Mode 2
Simple mode
Eco/NetworkStandby mode
P-timerCount up
TimerStart/Stop/Restart
Count down
SecurityOffProjectorRemote control
Key lock
Off/On 1/On 2PIN code changePIN code lock
HFilter counter
Yes/NoOff/400H/700H/1000HFilter counterTimerFilter counter reset
Yes/NoScroll(s)Scrolls remainingScroll counter Reset
8 test patterns providedTest pattern
Setting
ResetExit
SoundImageHDMI setup
Closed caption Closed captionColorOff/Low/Mid/HighVideo delay control
Picture in Picture
Protection
Factory default
ShutterOff
Both
PositionMenu sizeNormal/Double
Release keyAny/SHUTTER
Normal/EnhancedHDMI/AUDIO 1
78 
						

							Check the indicators for the projector condition.  
Indicators
Projector ConditionPOWERgreenLAMPred
WARNINGTEMP.red
WARNINGFILTERorange
SHUTTERblue
LAMPREPLACEorange
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/STAND-BY button to turn on the projector.
The projector is operating normally.
(The shutter is open)
The projector is operating normally.
(The shutter is closed)
The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed and the POWER indicator lights green.
The projection lamp is being cooled down in the Power management mode.
The projector is in the Power management mode.
The projection lamp is being cooled down in the Shutter management mode.
The projector is in the Shutter management mode.  Press the ON/STAND-BY button to turn on the projector.
The filter is scrolled using the FILTER button on the remote control or the Filter control function in the setting menu. When the filter is being scrolled, the Filter replacement icon and Please wait . . . message (Fig. 1) appear on the screen for about 30 seconds.
The projector is operating normally .
• • • on
• • • off
• • •   blinking at the normal rate       (approx. 1 second ON,         1 second OFF)
• • • dim• • •   blinking slow (approx. 2 seconds ON, 2 seconds OFF)




Appendix
Fig .1   Filter replacement icon and Please wait . . ..
• • • on (blue)❊❊• • •    blinking at the normal rate (blue and dim red) (approx. 1 second ON, 1 second OFF)
❊• • •  blinking fast (blue and dim red) (approx. 0.5 seconds ON,  0.5 seconds OFF)
• • •  blinking fast (approx. 0.5 seconds ON,  0.5 seconds OFF)• • • on (red)❖
❖• • • dim (red)
❖
❖

❖
❖
❖











• • • Differ according to conditions.






Indicators and Projector Condition
❊
❊
❊
❖
❖
❖
79 
						

							The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWERgreenLAMPred
WARNINGTEMP.red
WARNINGFILTERorange
SHUTTERblue
LAMPREPLACEorange
The temperature inside the projector is elevated close to the abnormally high level.
The temperature inside the projector is abnormally high. The projector cannot be turned on. When the projector is cooled down enough and the temperature returns to normal, the POWER indicator lights green and the projector can be turned on. (The WARNING TEMP. indicator keeps blinking.) Check and replace the filter.
The projector has been cooled down enough and the temperature returns to normal. When turning on the projector, the WARNING TEMP. indicator stops blinking. Check and replace the filter.
The lamp cannot light up. (The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed.)
The lamp cannot light up. (The lamp has been cooled down enough and the projector is in stand-by mode and ready to be turned on with the ON/STAND-BY button.)
The lamp has been used overtime. Replace the lamp immediately.
 When the filter detects clogging, reaches a time set in the timer settin\
g or runs out of the filter scroll, the WARNING FILTER indicator lights orange. When this indicator lights orange, replace \
the filter or the filter cartridge with a new one promptly. Reset the Filter counter and Scroll counter after replacing the filter\
 cartridge (p.68). 




Appendix
 When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights orange. When this indicator lights orange, replace the projection lamp with a new one prom\
ptly (p.69).
WARNING FILTER
LAMP REPLACE 





❖
❖
❖
❖
❖







80