Eiki Projector Lc Wns3200 User Manual

11
Top Control and IndicatorsPart names and functions
① POWER indicator
-   Lights red when the projector is in stand-   
by mode.
-   Lights green during operations.
-   Flashes green in the Power management     
mode.
-   Flashes red during fans cooling.
-   Lights  orange  when  abnormity  is  detected         
in the projector.
-   Flashes  orange  when  internal  temperature        
is abnormally high. 
②
 WARNING indicator
Lights red when the life of the projection      
lamp draws to an end.
③...

12
Remote control① POWER 
Turn on or turn off the projector.(Page 21)
② VGA
Select VGA as input source.(Page 28)
③ INPUT 
Enter input source menu to select input 
source directly. (Page 28)
④ HDMI 
Select HDMI as input source.(Page 28)
⑤ MENU
Open or close the screen menu.(Page 22)
⑥ COMPONENT 
Select component as input source.(Page 28)
⑦ BLANK 
Temporarily close the image on the screen. 
(Page 27)
⑧ VIDEO 
Select Video as input source.(Page 28)
⑨ S-VIDEO 
Select S-video as input source.(Page 28)
⑩ ...

13
⑱⑲
⑳
⑭
⑯ ⑫
⑬
⑮
⑰
⑫  D
.ZOOM+
Select the digital zoom + mode.(Page 27)
⑬ TIMER 
Enable the timer function.(Page 27)
⑭  VOUME +  
Increase the volume level.(Page 24)
⑮ AUTO 
Enter auto setup mode.(Page 25)
⑯  VOUME -  
Decrease the volume level.(Page 25)
⑰  FREEZE 
Freeze the projected image.(Page 26)
⑱ D
. ZOOM- 
Select the digital zoom - mode.(Page 27)
⑲
 MUTE Mute the sound.(Page 25)
⑳  BACK 
Return to main menu.(Page 22)
Part names and functions  

14
Adjustable foot
Operating range
Install remote control batteries
①   Open the battery      
compartment lid.  ② Install new batteries  
into the compartment.③ Replace the 
compartment lid.
Two AAA  batteries
For correct polarity 
(+ and –), be sure 
battery terminals 
are in contact 
with pins in the 
compartment.
Point the remote control toward the projector 
remote receiver when pressing any button. 
The maximum operating range for the remote 
control is about 5 meters and 60 degrees 
vertically and...

15
Positioning the projector
XNS2600,XNS3100 (4:3):
XNS2600,XNS3100 (16:9):
WNS3200 (16:9): WNS3200 (16:10):
Installation
 Note:
●  The brightness in a room has a great influence on picture quality
. It is recommended to limit the 
     ambient lighting in order to get the best image.
●  All measurements are approximate and may vary from the actual sizes.
Screen size
(WxH)mm
4:3 aspect 
ratio 30
" 100
" 150
" 200
" 300
"
610x457 2032x1524
3048x2286 4064x30486096x4572
Maximum...

16
Connecting to computer(Digital and analog RGB)
Installation
Cables used for connection:
● VGA cable                                                              ● Serial control cable*
● HDMI cable*                              
(*=Cables are not supplied with the projector)
Unplug the power cords of both the projector and external equipment from the 
AC outlet 
before connecting the cables.
HDMI output
HDMIcable
HDMI
RS-232C port Serial output
Serial 
control 
cable Monitor output
Monitor input
VGA...

17
Connecting to video equipment (Video, S-Video)Installation
Cables used for connection:
● Video cable*                                                   ● S-Video cable*
●  RCA cable*                                                    ● Audio cable*
(*=Cables are not supplied with the projector)
 
S-VIDEO INS-video 
ouput Video 
ouput
Component
 output Audio
 output Audio
 output Audio
 output
VIDEO IN
S-VIDEO
cable
RCA
cable
Audio
cable
Audio
cableAudio
cable
Video
cable
COMPONENT AUDIO IN
L/R AUDIO...

18
(R)   (L)(R)   (L)
Audio 
cable
Audio cable
(stereo)
Audio cable
(stereo) Note: The left and right 
channels  are combined when 
there  is  only  the  L(mono)  is           
inserted.
External audio equipment
Unplug the power cords of both the projector and external equipment from the 
AC outlet 
before connecting the cables.
Connecting to audio equipment
Installation
Cables used for connection:
● Audio cable*                              
(*=Cables are not supplied with the projector)
Audio input...

19
Connecting the AC power cord
Installation
Connect the AC power cord to the projector.
This projector uses nominal input voltages of 
100–240V AC and it automatically applies to 
different input voltages. It is designed to work 
with a single-phase power system having a 
grounded neutral conductor. To reduce the risk 
of electrical shock, do not plug into any other 
type of power system. If you are not sure of 
the type of power being supplied, consult your 
authorized dealer or service station....

20
Turn on the projector
1. 
Complete peripheral connections (with a  
computer, VCR, etc.) before turning on the  
projector.
2.   Connect the projector’s AC power cord into  
AC outlet. The POWER indicator turns red. 
3.   Press the POWER button on top control or   
on the remote control. The POWER indicator  
becomes green and the cooling fans start to 
work. The preparation display appears on  
the screen and the countdown starts.
4.   If the projector is locked with a PIN code, a 
PIN code input...