Eiki Projector Lc Wb42na User Manual

							
71

Appendix
			– Check PC adjustment  or Screen and adjust them.                              
                                                                    See pages 34-35, 38-39 .         
	 	  – PIN code lock is being set. Enter a PIN code ("
1234"   or numbers 
 	   you have set). See pages 22, 59-60. 
	 								 – Make sure your computer is connected to the projector with USB  
 					 	cable. See page 17.             
    – Check cable connection between the projector and your computer.  
     See page 17.
	 	  – Check the batteries.
 
 	  – Make sure no obstruction is between the projector and remote   
       control.
 
    – Make sure you are not too far from the projector when using the  
     remote control. Maximum operating range is 16.4'(5 m).                    
                         – Make sure the code of the remote control is conformed to the    
        projector’s code. See page 58. 
 
    – Unlock the Key lock function for the remote control function. See  
     page 59.
    –  Check RESET/ON/ALL-OFF switch on the remote control is set to 
ON. See page 12. 
 		 – Check the status of the projector with referring to "Indicators and  
     projector Condition". See page 75.          
   
 		  – Check the connection between the projector and your computer. 
 			 – Check the mouse setting on you computer.       
    – Make sure the mouse driver is installed on your computer,    
     otherwise, the remote control can not be used as a wireless mouse. 
    – Make sure the signal is  from the computer, otherwise, the remote  
     control can not be used as a wireless mouse.       
    – Turn on the projector before turning on the computer.
 	  – Your operation is invalid. Operate correctly.       
  	
	 																																																															
– The top control is not available if the top control is locked at  Key	lock  
       under 
Security of Setting section. See page 59.
 	  – Contact the dealer where you purchased the projector or the service 
 	   center.               
 	
The	image	is	distorted	or	runs	off .	
PIN	code	dialog	box	appears	at	
start-up .
Page	Up/Down	function	does	not	
work .
The	Remote	Control	does	not	work .
Indicator	blinks	or	lights .
Wireless	Mouse	function	does	not	
work .
The	exclamation	mark	appears	on	
the	screen .
Top	control	does	not	work .
Unable	to	unlock	the	Logo	PIN	code	
lock,	Security	key	lock	or	Security	
PIN	code	lock . 
						

							
72

WARNING	:
High	voltages	are	used	to	operate	this	projector .	Do	not	attempt	to	open	the	cabinet .
If problems still persist after following all operating instructions, contact the dealer where you purchased the 
projector or the service center. Specify the model number and explain about the problem. We will advise you 
how to obtain service.
This symbol on the nameplate 
means the product is Listed 
by Underwriters Laboratories 
Inc. It is designed and 
manufactured to meet rigid 
U.L. safety standards against 
risk of fire, casualty and 
electrical hazards.
The CE Mark is a Directive conformity 
mark of the European Community (EC).
AppendixAppendix 
						

							
73

Appendix
Menu	Tree
SVGA 1Mode 1Mode 2 - - - -
Total dotsHorizontalVertical
Display area HDisplay area VReset
Dynamic
RealBlackboard (Green)
Image 1Image 2Image 3
Image	 AdjustContrastBrightnessColor temp.
Red
Gamma
Store
Normal
True
Digital zoom –
Full 
0–630–63
Computer	Input
PC	adjust
Mode 1Mode 2Mode 3Mode 4Mode 5
Image	Select
0–63
0–15
Image 1Image 2Image 3Image 4Screen
Yes/No
 * Systems displayed in the System Menu vary depending on an input signal.
ResetYes/No
Sharpness0–15
Computer	Input/HDMI	Input/Video	Input
Sound
VolumeMuteOn/OffSound0-63
Standard
Mode 3Mode 4Mode 5
Clamp
Digital zoom +
GreenBlue0–630–63
Store
Mode free
System	(1)
Mid
LowXLow
User
Image 4
Fine sync0–31
Mode 1Mode 2
CustomScaleH&VPositionCommonReset
H/V
H/VYes/NoYes/No
On/Off
Input
Computer 2
Video
RGB 
RGB (Scart)
Computer 1
Component
Input
RGB
Colorboard
High
S-video
Network
Red/Blue/Yellow/Green
Auto PC adj.
HDMI 
						

							
74

Appendix
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
HDMI	Input	/	Video	Input
Auto1080i1035i720p575p480p575i480i
Dynamic
CinemaBlackboard (Green)
Image 1Image 2Image 3
Normal
0–630–63
Off
Setting
Image	Select
System	(2)
System	(3)
Image	AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0–630–630–630–15 0–15
Image 1
Screen
Yes/No
Image 4
LanguageSetting17 languages provided.
Blue/User/BlackOn/Countdown off/Off Logo select
On/OffOn/Off
On/Off
Code 1–Code 8
KeystoneBackgroundDisplayLogo
CeilingRear
On start
Remote control
Security
PIN code lock
Off
Power managementReadyShut down
Timer (1–30 Min)
L1/L2Fan
Standard
OffNoise reduction
Store/Reset
L1L2
0–630–63
Image 2Image 3Image 4
L2L1
Off
User
CaptureYes/No
Off/OnLogo PIN code change
Logo PIN code lock
OffProjectorRemote control
Key lock
Default
Off/On1/On2PIN code change
Film
On/Off
Standby modeNetwork / Eco
Closed CaptionClosed Caption
Color temp.
Auto PC adj.
Auto KeystoneAutoManualOff
Offl/On1/On2/On3Fan control
Warning log
HFilter counter
Yes/NoOff/100H/200H/300H
Yes/NoFactory default
Wide
Scale
PositionCommonReset
H/V
H/VYes/NoYes/No
Custom
PointerSpotlight L / Spotlight M / Spotlight S / Arrow / Finger / Dot
On/OffH&V
Colorboard
Input searchOff/On1/On2Auto setup
Off/CC1/CC2/CC3/CC4ColorColor/WhiteLamp controlAuto/High/Normal/Eco
Filter counterTimerFilter counter reset
InformationInput Source Information Display
Menu position
Mid
LowXLow
UserHigh
Red/Blue/Yellow/Green
FullZoom
Natural wide
ImageHDMI setupNormal
SoundEnhanced
HDMIComputer 2Computer 2/Monitor outTerminal
ModePicture in PictureOff/P in P/P by P
Subpicture sizeSmall/Middle/Large
Subpicture position
Lamp counterLamp counterLamp counter reset 
						

							
75

Check the indicators for projector condition.                                   
• • • green• • • red• • • off
• • • blinks green
When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator 
lights yellow, replace the projection lamp with a new one promptly.
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/STAND-BY button 
to turn on the projector.
Projector	Condition
POWERred/green
Indicators
LAMP REPLACEyellow
WARNING red

The projector is preparing for stand-by or the projection lamp is 
being cooled down. The projector cannot be turned on until cooling 
is completed and the POWER indicator stops blinking.
The temperature inside the projector is abnormally high. The 
projector cannot be turned on. When the projector is cooled down 
enough and the temperature returns to normal, the POWER 
indicator stops blinking and the projector can be turned on. (The 
WARNING indicator keeps blinking.) 

The projector detects an abnormal condition and cannot be turned 
on. Unplug the AC power cord and plug it again to turn on the 
projector. If the projector is turned off again, unplug the AC power 
cord and contact the dealer or the service center for service and 
checkup. Do not leave the projector on. It may cause an electric 
shock or a fire hazard.

The projector is operating normally. 
The projector is in the Power management mode. 

The projector has been cooled down enough and the temperature 
returns to normal. When turning on the projector, the WARNING 
indicator stops blinking. Check and clean the filters.
Indicators	and	Projector	Condition
• • • blinks red
Appendix 
						

							
76

Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with t\
he V-, H-Frequency mentioned below 
and less than 140 MHz of Dot Clock for analog signal and 110 MHz of Dot Clock for digital signal.
  When selecting these modes, PC adjustment can be limited.
ON-SCREEN DISPLAYRESOLUTIONH-Freq.(KHz)V-Freq.(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
SXGA 11152 x 86464.2070.40
SVGA 1800 x 60035.15656.25
SVGA 2800 x 60037.8860.32
SVGA 3800 x 60046.87575.00
SVGA 4800 x 60053.67485.06
SVGA 5800 x 60048.0872.19
SVGA 6800 x 60037.9061.03
SVGA 7800 x 60034.5055.38
SVGA 8800 x 60038.0060.51
SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
ON-SCREEN DISPLAYRESOLUTIONH-Freq.(KHz)V-Freq.(Hz)
XGA 101024 x 768
XGA 111024 x 768
XGA 121024 x 768
XGA 131024 x 768
62.0477.07
XGA 141024 x 768
61.0075.70
XGA 151024 x 768
35.52286.96(Interlace)
46.9058.20
XGA 81024 x 768
47.0058.30
XGA 91024 x 768
58.0372.00
SXGA 41280 x 1024
63.4879.35
36.0087.17(Interlace)
63.3459.98
SXGA 51280 x 1024
SXGA 61280 x 1024
SXGA 71280 x 1024
63.7460.01
71.6967.19
SXGA 101280 x 960
81.1376.107
60.0060.00
XGA 11024 x 768
XGA 41024 x 768
48.3660.00
XGA 61024 x 768
XGA 71024 x 768
56.47670.07
48.5060.02
44.0054.58
SXGA 81280 x 1024
SXGA 91280 x 1024
63.9860.02
79.97675.025
XGA 51024 x 76860.3174.92
VGA 7640 x 48043.26985.00
575i768 x 57615.62550.00(Interlace)
480i640 x 48015.73460.00(Interlace)SXGA 121152 x 90071.4075.60
SXGA 111152 x 90061.2065.20
SVGA 10800 x 60032.7051.09
SXGA 131280 x 102450.0086.00(Interlace)
SXGA 21280 x 102462.5058.60
SXGA 31280 x 102463.9060.00
XGA 21024 x 76868.67784.997
XGA 31024 x 76860.02375.03
SXGA 181280 x 102446.4386.70(Interlace)
SXGA 191280 x 102463.7960.18
SXGA 141280 x 1024
SXGA 151280 x 1024
SXGA 161280 x 1024
SXGA 171152 x 900
50.0094.00(Interlace)
63.3760.01
76.9772.00
61.8566.00
MAC1280 x 96075.0075.08
MAC1280 x 102480.0075.08
SXGA+ 11400 x 105063.9760.19
MAC211152 x 87068.6875.06
WXGA 21360 x 768
WXGA 31376 x 768
WXGA 41360 x 768
47.7060.00
48.3660.00
56.1672.00
WXGA 11366 x 768
1080i1920 x 108033.7560.00(Interlace)
1035i1920 x 103533.7560.00(Interlace)
1080i1920 x 108028.12550.00(Interlace)
48.3660.00
SXGA+ 21400 x 105065.3560.12
SXGA+ 31400 x 105065.1259.90
SXGA 201280 x 102491.14685.024
480p640 x 48031.4759.88
575p768 x 57531.2550.00
WXGA 71280 x 768
WXGA 81280 x 768
60.28974.893
68.63384.837
WXGA 61280 x 76847.77659.87
MAC 191024 x 76860.2475.08
720p1280 x 72037.5050.00
720p1280 x 72045.0060.00
WXGA 101280 x 800
WXGA 111280 x 800
41.20050.000
49.70259.810
WXGA 91280 x 80049.60060.050
When the input signal is Analog , refer to the chart below.
UXGA 41600 x 120093.7575.00
UXGA 11600 x 1200
UXGA 21600 x 1200
UXGA 31600 x 1200
75.0060.00
81.2565.00
87.570.00
WXGA +11440 x 90055.93559.887
WSXGA +11680 x 105065.29059.954
WXGA +21440 x 90074.91860.000
WUXGA 21920 x 120074.03859.950
WUXGA 11920 x 120074.55659.885
WXGA 121280 x 80063.9860.02 
						

							
77

Appendix
ON-SCREEN DISPLAYRESOLUTIONH-Freq.(KHz)V-Freq.(Hz)
D-VGA640 x 48031.4759.94
D-480p720 x 480----59.94
D-575p720 x 575----50.00
D-SVGA800 x 60037.87960.32
D-WXGA 11366 x 76848.3660.00
ON-SCREEN DISPLAYRESOLUTIONH-Freq.(KHz)V-Freq.(Hz)
D-1035i1920 x 1035
D-1080i1920 x 1080
D-1080i1920 x 1080
33.7560.00(Interlace)
33.7560.00(Interlace)
28.12550.00(Interlace)D-XGA1024 x 76843.36360.00
D-WXGA 21360 x 76847.760.00
D-WXGA 31376 x 76848.3660.00
Note:
• The specifications are subject to change without notice.
• Depending on your PC settings, the digital signals of your PC may n\
ot be projected correctly. In such a case, 
  confirm your PC settings.
• When you project a DVI signal, connect the cables, turn the project\
or on, then select the input. Finally, turn 
  on your PC. Be sure to follow this procedure, otherwise an image may n\
ot be projected on the screen. If an 
  image is not projected correctly, restart your PC.
• Do not disconnect the cable while the projector is running. If the \
cable has been disconnected and then 
  reconnected, an image may not be correctly projected.
D-WXGA 41360 x 76856.16072.000
D-WXGA 51366 x 76846.50050.000
D-WXGA 61280 x 76847.77659.870
D-WXGA 71280 x 76860.28974.893
D-SXGA11280 x 102463.9860.02
D-SXGA21280 x 102460.27658.069
D-SXGA31280 x 102431.6529.80
D-WXGA 81280 x 76868.63384.837
D-WXGA 91280 x 80049.57259.870
D-WXGA 101280 x 80041.20050.000
D-WXGA 111280 x 80049.70259.810
D-SXGA+ 11400 x 105063.9760.19
D-SXGA+ 21400 x 105065.35060.120
D-SXGA+ 31400 x 105065.12059.900
D-WSXGA +11680 x 105065.29059.954
D-UXGA1600 x 120075.00060.000
D-WUXGA 21920 x 120074.03859.95
When the input signal is digital from HDMI terminal, refer to the chart \
below.
D-WXGA +11440 x 90055.93559.887
D-480p640 x 48031.4759.88
D-480p720 x 480----60.00
D-575p768 x 57531.2550.00
D-720p1280 x 72037.5050.00
D-720p1280 x 720----59.94
D-720p1280 x 72045.0060.00
D-VGA640 x 480----60.00
D-1080i1920 x 1080----
D-1080p1920 x 1080----59.94
D-1080p1920 x 1080----60.00
D-1080p1920 x 1080----50.00
59.94(Interlace)
D-WXGA 121280 x 80063.9860.02 
						

							
78

List	of	Picture	in	Picture
 o : Picture in Picture combinations are enabled
 - : Picture in Picture combinations are disabled
Note: •  When the input signal(s) is/are incompatible, X mark will be displayed on the Main/Sub picture.
  •  Depending on the frequency or signal type of PC/AV input, 
the display resolution may be lowered or images may not be displayed on 
the Main/Sub picture.
　　
    •  Inputting PC analog signals: Between 100-140 MHz
　　
    •  Inputting PC analog signals: More than 140MHz
    •  Inputting PC digital signals: More than 100MHz
    •  Inputting AV digital signals: 1080p
　　
    •  Inputting signal formats: SXGA20, WUXGA 1, WUXGA 2, WSXGA+ 1, WXGA+2, UXGA 1, UXGA 2, UXGA 3, UXGA4, D-1080p
Appendix 
						

							
79

Appendix
Technical	Specifications
Mechanical	Information	 
  Projector Type  Multi-media Projector 
  Dimensions (W x H x D)  13.16" x 3.09" x 10.30 (334.2 x 78.4 x 261.5mm) (Not including protrusions)
 
  Net Weight   8.2 lbs (3.7 kg)
 
  Feet Adjustment  0˚ to 8.9˚           
              
Panel	Resolution	 
 LCD Panel System  0.74" TFT Active Matrix type, 3 panels  
  Panel Resolution  1,280 x 800 dots
   Number of Pixels                                              3,072,000 (1,280 x 800 x 3 panels)
                
Signal	Compatibility	  
 Color System PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N 
  High Definition TV Signal  480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
 
 Scanning Frequency  H-sync. 15 kHz–100 kHz, V-sync. 50–100 Hz         
 
Optical	Information	
 Projection Image Size (Diagonal)  Adjustable from 40” to 300” 
  Throw Distance  3.3' (1.0m) - 39.7' (12.1m)           
  Projection Lens  F1.7–2.5 lens with f=19.2 mm–30.2 mm with manual zoom and focus
 
  Projection Lamp  275 W            
  
Interface
 Video Input Jack  RCA Type x 1  
  S-video Input Jack  Mini DIN 4 pin x 1
 
  Audio Input Jacks  RCA Type x 2
   Computer 1 /Computer2 Audio Input Jacks  Mini Jack x 2
 
  Computer In 1/ Component Input Terminal      Mini D-sub 15 pin x 1
 
  Computer In 2/MONITOR OUT Terminal          Mini D-sub 15 pin x 1
 
  Control port    D-sub 9 pin x 1
 
  USB Connectors  USB connector (Series A x1, Series B x 1)
 
  Audio Output Jack  Mini Jack (stereo) x 1 (variable)           
  LAN Connection Terminal                                100 Base-TX (100Mbps)/10 Base-T (10Mbps), RJ45
   HDMI                                                                x 1
     
 
Audio	
 Internal Audio Amp  1.0 W RMS 
  Built-in Speaker  1 speaker, ø1.10" (28 mm) 
 
 
Power
 Voltage and Power Consumption  AC 100–120 V (4.0A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
                                                      AC 200–240 V (2.0A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)
 
         
Operating	Environment
 Operating Temperature  41˚F–95˚F (5 ˚C–35 ˚C) 
  Storage Temperature  14˚F–140˚F (-10˚C–60 ˚C)
 
 
Remote	Control	
  Battery  AAA or LR03 Type x 2           
  Operating Range  5 m/±30˚
 
  Dimensions  45 mm (W) x 23 mm (H) x 145 mm (D)           
  Net Weight  3.5 oz 99 g (including batteries)           
 Laser Pointer Class II Laser (Max. Output: 1 mW/Wave length: 640–660 nm)  
						

							
80

Appendix
	 			Model No.
COMPONENT~VGA	Cable																					:	AH-98771
SCART~VGA 	Cable																																:	
AH-98881
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. 
to the sales dealer.
Optional	Parts
Accessories
 Owner’s Manual (CD-ROM)
   Quick Reference Guide 
   Safety Manual 
  AC Power Cord
 
  Remote Control and Batteries                     
  VGA Cable
  PIN Code Label
 
  Network Application (CD-ROM)
  Soft Carrying Case
  USB thumb drive for Auto Capture
  Case (for USB thumb drive)
  Hook and Loop Fastener
  Remote control cable
●   The specifications are subject to change without notice.
●    LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are 
effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD 
panels.