Eiki Projector Lc Wb100 User Manual

							
51

Setting
Picture in PictureThis	function	is	used	to	project	two	videos	simultaneously
by	placing	a	separate	small	sub	screen	within	the	main
screen.	(Picture	in	Picture	combinations	provided	in	this	
projector	are	shown	on	pages	75.)
Only	the	sound	on	the	main	picture	is	heard,	the	sound
on	the	sub	picture	cannot	be	heard.(	In	
P in P,	the	big	
picture	is	main	picture,	and	the	small	one	is	sub	picture;	in	
P 
by P ,	the	left	picture	is	main	picture,	and	the	right	one	is	sub	
picture.)
  Mode . 	.	.	.	.	
P in P :		The	sub	picture	in	the	main	picture.
																					P by P :		The	sub	picture	by	the	main	picture.
																					Off  				:			Exit	the	Picture	in	Picture	menu.
  Subpicture size . 	.	.		Select	the	subpicture	display	size.	
																																				Subpicture	can	be	changed		
																																				between	
Large, Small 	and	Middle .	
  Subpicture position. .		Set	a	position	for	subpicture. This	
																																									function	is	used	to 	set	
Subpicture 
                                         position	as	follows:
																																									the	top	left→	the	bottom	left	→
																																									the	bottom	right→	the	top	right→
	•	•	•
Selecting the Main picture or Sub picture
During	Picture	in	Picture	mode,	and	no	operation	on	the	On	
Screen	Menu,	press	the	SELECT 	button	to	select	main	or	
sub	picture.	(When	the	sub	picture	is	selected,	a	red	frame	
will	be	displayed.)
Switching of the Input Source
In	the	main	picture	or	the	sub	picture	mode,	 choose	input	
soucre by	pressing	the	INPUT 	button	on	the	top	control	or	
pressing	the	COMPUTER	1/2,	HDMI,	VIDEO,	S-VIDEO	or	
COMPONENT 	button	on	the	remote	control	or	through	Input	
Menu	operation.
Operation of the Sub picture
In	Picture	in	Picture	mode,	press	the	SELECT 	button	to	
select	the	sub	picture	(the	frame	becomes	red),	and	then	
use	the	Point	▲▼◄►	buttons	to	change	Subpicture	size,	
switch	the	Main	picture	and	the	Sub	picture,	and	move	
Subpicture	position.
			•	In	Picture	in	Picture	mode,	press	the	Point	▲	button	to			
					switch	the	Main	picture	and	the	Sub	picture.	
			•	In	P 	in	P,		press	the	Point	▼	button	to	change	Subpicture			
					size.
			•	In	P 	in	P,		press	the	Point	◄►	buttons	to	move	
					Subpicture	position.
Picture in Picturemore...Standby mode                                          Network
Picture in Picture
Note:
• 	When	the	input	signal(s)	is/are	incompatible,	X 	mark	will
		be	displayed	on	the	Main/Sub	picture.
• 	When	the	sub	picture	is	set	to	the	same	signal	as	the	main
		picture,	
X 	mark	will	be	displayed.
		•	
Subpicture position 	and	Subpicture size	are	only	used		
				for	
P in P.
Subpicture size
Note:
• 	When	P in P 	or	P by P 	is	set,	Total dots  is	
		disabled	in	the	PC	adjust	menu.	
• 	In	Picture	in	Picture	mode,	the	Freeze	function	
		is	disabled
.
• 	During	Picture	in	Picture	mode	and	the	Menu	
		screen	is	displayed,	below	functions	via	the	
		remote	control	operation	are	disabled.
			• 	Change	Subpicture	size.
			•	Move	Subpicture	position.
			•	Switching	of	the	Main	picture	and	Sub	picture.
			•	Select	the	Sub	picture	mode	by	the	SELECT 			
					button. 
						

							
5

Setting
Power management
Timer	left	before	Lamp	is	off.
Power management
For	reducing	power	consumption	as	well	as	maintaining	
the	lamp	life,	the	Power	management	function	turns	off	the	
projection	lamp	when	the	projector	is	not	operated	for	a	
certain	period.
Select	one	of	the	following	options:
Ready	.................. 	When	the	lamp	has	been	fully	cooled	
down,	the	POWER	indicator	changes	
to	green	blinking.	In	this	condition,	the	
projection	lamp	will	be	turned	on	if	the	
input	signal	is	reconnected	or	any	button	
on	the	top	control	or	remote	control	is	
pressed.	
Shut down 	.......... 	When	the	lamp	has	been	fully	cooled	
down,	the	power	will	be	turned	off.	
Off 	....................... 	Power	management	function	is	off.	
Timer	................... 	If	the	input	signal	is	interrupted	and	
no	button	is	pressed	for	more	than	
30	seconds,	the	timer	display	with	
No 
signal 	appears.	It	starts	the	countdown	
until	the	lamp	is	turned	off.	Use	the	Point	
▲▼	buttons	to	set	the	 Timer(1~30min).
Note:
		Factory	default	is	
Ready: 5 min.
Standby mode
This	function	is	available	when	operating	the	projector	via	
network.
	Network 	.... 	Supply	 the	power	 to	the	 network	 function	 even	
after	turning	off	the	projector.	 You	can	turn	on/
off	the	projector	via	network,	modify	network	
environment,	and	receive	an	e-mail	about	
projector	status	while	the	projector	is	powered	
off.
	Eco 	............ 	Select	Eco	when	you	do	not	use	the	projector	
via	network.	 The	projector’s	network	function	
will	stop	when	turning	off	the	projector.
Refer	to	the	owner’s	manual	of	“Network	Set-up	and	
Operation”.
Note:
•	Factory	default	is	
Eco.
•	When	selecting	
Network ,	the	cooling	fans	may	be	running	
		depending	on	the	temperature	inside	the	projector	even	if	
		the	projector	is	turned	off. 
						

							
5

Setting
On start
When	this	function	is	set	to On,	the	projector	will	be	
automatically	turned	on	just	by	connecting	the	 AC	power	
cord	to	a	wall	outlet.	
Note:
•	 Be	sure	to	turn	off	the	projector	properly	(see	"Turning	Off	
the	Projector"	on	page	20).	If	the	projector	is	turned	off	
in	the	incorrect	sequence,	the	On	start	function	does	not	
work	properly.
•	 On	start	function	is	available	only	when
 Network 	is	
selected	in	Standby	mode	function.	(p.52)
On start 
						

							
54

Press	the	Point	▲▼	buttons	to	
select	
Off ,	CC1 ,	CC ,	CC 	or	CC4,	
and	then	Press	Select	button.
Setting
Closed caption
Closed	Caption	is	a	function	that	displays	the	audio	portion
of	a	 TV	program	as	text	on	the	screen.	If	the	input	signal	
contains	closed	captions,	you	can	turn	on	the	feature	and	
switch	the	channels.	Press	 the	Point	▲▼	buttons	to	select	
Off,	CC1 ,	CC ,	CC 	or	CC4.		
If	the	closed	caption	is	not	clear,	you	can	change	the	text	
from	
Color 	to	White.
Closed Caption
Note:
The	Closed	Caption	is	available	only	under	the	situation	
below.
    •	When	the	input	signal	is	NTSC 	of	composite	and									
						S-video,	and	the	system	is	set	according	to	the	signal		
						or	set	on	
Auto .		
	 	 •	 The	system	must	be	set	on	
NTSC 	or	Auto	in	Video				
		System	Selection.	(p.39)	
	 	 •	 The	icon	of	Closed	caption	is	displayed	in	gray	while	it 	
							is	not	available.	
	 	 •	 The	Closed	caption	is	unavailable	when	On-Screen
						menu	and	P-Timer	are	displayed,	and	Picture	in	
							Picture	is	active.
Power management                                      Off                  On start                                                         Off 
						

							
55

Remote control
This	function	allows	you	to	change	brightness	of	the	
screen.
Normal	...... 	Normal	brightness	
Eco 	............ 	Lower	brightness	reduces	the	lamp	
power	consumption	and	extends	the	
lamp	life.
Lamp control 
Remote control
Lamp life control
This	projector	provides	two	different	remote	control	codes:	
the	factory-set	initial	code	(Code	1)	and	the	secondary	code	
(Code	2).	 This	switching	function	prevents	remote	control	
interference	when	operating	several	projectors	or	video	
equipment	at	the	same	time.
When	operating	the	projector	in	 Code ,	both	the	projector	
and	the	remote	control	must	be	switched	to	 Code 
.
To change the code for the projector:
Select	either	
Code 1	or	Code  	in	this	Setting	Menu.
To change the code for the remote control:
Press	and	hold	both	the	MENU	and	IMAGE	buttons	
together	for	5	seconds	or	more.		 After	changing	the	code,	
make	sure	the		remote	control	operates	properly.
Lamp control
Select	the	lamp	operation	when	the	total	lighting	time	of	a	
lamp	exceeds	the	recommended	total	hours	of	use.
Mode 1 	.............. 	A	lamp	can	be	turned	on	even	after	
exceeding	the	recommended	total	
hours	of	use.
Mode  	.............. 	A	lamp	can	be	turned	on	even	after	
exceeding	the	recommended	total	
hours	of	use.	But	the	projector	turns	off	
automatically	after	3	minutes.
Lamp life control
Note:
•	When	different	codes	are	set	on	the	projector	and	on	the	remote	control,	any	operation	cannot	be	made.	In	
			that	case,	switch	the	code	on	the	remote	control	to	fit	the	code	on	the	projector.
•	If	the	batteries	are	removed	from	the	remote	control	for	a	long	period	of	time,	the	remote	control	code	will	be	
		reset.
Power management                                      Off                  On start                                                         Off
	Note:
•	 Lamp	mode	cannot	be	changed	for	a	while	after	turning	
		on	the	projector.	Lamp	needs	some	time	to	stabilize	
		after	the	power	is	turned	on.	Stored	lamp	mode	will	be	
		active	after	the	lamp	is	stabilized.
•	If	 Mode  	has	been	selected	and	the	projection	lamp	
		exceeds	the	recommended	total	hours	of	use,	the	
		replacement	icon	will	be	displayed	at	the	time	of	power-
		on.	 Then	the	projector	will	turn	off	after	3	minutes.
	 •	 The	Lamp	replacement	icon	will	not	appear	when	the	
				Display	function	is	set	to	
Off 	(p.46),	during	"FREEZE	
button"	(p.25),	or
  "NO	SHOW	button"	(p.26).
Lamp replacement icon
Setting 
						

							
56

Key lock
Key lockSecurity (Key lock and PIN code lock)
PIN code lock
This	function 	locks 	the 	top 	control 	and 	remote 	control	
buttons	to	prevent	operation	by	unauthorized	persons.
Select	
Key lock 	and	 then	 press	 the	SELECT 	button,	 and	
select	the	desired	item	by	pressing	the	Point	
▲▼	buttons.
	 .....	Unlocked.
	 ..... 	Lock	the	operation	of	the	top	control.	 To	
unlock,	use	the	remote	control.
	 ..... 	Lock	the	operation	of	the	remote	control.				
To	unlock,	use	the	top	control.
If	 the	 top	control	 accidentally	 becomes	locked	and	you	do	
not	 have	 the	remote	 control	nearby	 or	there	 is	something	
wrong	 with	your	 remote	 control,	 contact	the	dealer	 where	
you	purchased	the	projector	or	the	service	center.
This	 function	 allows	you	to	use	 the	Key	 lock	 and	PIN	code	
lock	function	to	set	the	security	for	the	projector	operation.
This	function	prevents	the	projector	from	being	operated	
by	unauthorized	persons	and	provides	the	following	
setting	options	for	security.
	 Off 	............	Unlocked.
	 On1 	.......... 	Enter	the 	PIN 	code 	every 	time 	turning 	on	
the	projector.
	 On2 	.......... 	Enter	 the	PIN	 code	 to	operate	 the	projector	
once 	the 	power 	cord 	is 	disconnected; 	as	
long 	as 	the 	AC 	power 	cord 	is 	connected,	
the 	projector 	can 	be 	operated 	without 	a	
PIN	code.
Whenever	 you	change	 the	PIN	 code	 lock	setting	 or	the	
PIN 	code 	(the 	four-digit 	number), 	you 	are 	required 	to	
enter	 the	PIN	 code.	 The	“1234”	 is	set	 as	the	 initial	 PIN	
code	at	the	factory.	
If	 you	 want	 to	change	 the	PIN	 code	 lock	setting,	 Press	
t h e 	S E L E C T 	b u t t o n 	a n d 	t h e 	P I N 	c o d e 	d i a l o g 	b o x	
appears.
PIN code lock
Setting
When 	the 	projector 	is 	locked 	with 	the 	PIN 	code, 	the	
Security	icon	appears	on	the	guide.
Power management                                      Off                  On start                                                         Off 
						

							
57

Use	the	Point	▲▼	buttons	to	select	Off,	On1 	or	On ,	and	
then	press	the	SELECT 	button	to	make	a	choice.
Change the PIN code lock setting
Enter a PIN code
Use	the	Point	▲▼	buttons	 to	enter	 a	number.	 Press	the	
Point	
►	 button	 to	fix	 the	 number	 and	move	 the	red	 frame	
pointer	 to	the	 next	 box.	The	number	 changes	 to	“
”.	 If	
you	 fixed	 an	incorrect	 number,	use	the	Point	
◄	button	 to	
move	 the	pointer	 to	the	 number	 you	want	 to	correct,	 and	
then	enter	the	correct	number.
Repeat	this	step	to	complete	entering	a	four-digit	
number.
After	 entering	 the	four-digit	 number,	move	the	pointer	 to	
“Set.”	 Press	 the	SELECT 	button	 so	that	 you	can	start	 to	
operate	the	projector.
If	 you	 entered	 an	incorrect	 PIN	code,	
PIN  code 	and	 the	
number	 (
)	will	 turn	 red	for	a	moment.	 Enter	the	
correct	PIN	code	all	over	again.
Enter a PIN code
The	PIN	code	can	be	changed	to	your	desired	four-digit	
number.	Press	the	SELECT 	button	to	select	
PIN code 
change.	PIN code 	dialog	box	appears,	use	the	Point	
▲▼	buttons	to	enter	the	correct	code.	 The	New	PIN	code	
input	dialog	box	appears.	Set	a	new	PIN	code.
Change the PIN code
CAUTION:
WHEN yOU  HAVE CHANGED  THE PIN  CODE, WRITE 
DOWN  THE  NEW  PIN  CODE  IN  COLUMN  OF  THE 
PIN  CODE  NO .  MEMO  ON  PAGE   80, AND KEEP  IT 
SECUREL y .  IF  yOU  FORGET  yOUR  PIN  CODE, THE 
PROjECTOR CAN NO LONGER BE STARTED .
Setting
PIN code change 
						

							
58

This	function	 provides	 the	following	 options	in	the	 cooling	
fans’ 	operation	when	the	projector	is	turned	off	(p.20).
	L1	...... 	Normal	operation
	L 	...... 	S l o w e r 	a n d 	l o w e r - s o u n d 	t h a n 	t h e 	n o r m a l	
operation	 (
L1),	but	 it	takes	 more	time	to	cool	 the	
projector	down.
Fan
This	projector	provides	Fan	control	function	in	the	Setting	
menu.
Choose	the	running	speed	of	cooling	fans	from	the	following	
options	according	to	the	ground	elevation	under	which	you	
use	the	projector.	
Off ................	Normal	speed.	Set	this	function	to	Off	when	
																						using	the	projector	in	non-high	altitude	
																						environment.	
On 1 .............	Faster	than	Off	mode.	Select	this	mode	
																						when	using	the	projector	in	high	altitudes	
																						(about	1,200	meters	or	more	above	the	sea	
																						level)	where	the	fans	have	less	cooling	
																						effect.	
On  .............	Faster	than	On	1	mode.	Select	this	mode	
																						when	using	the	projector	in	higher	altitudes	
																						than	above	where	the	fans	have	lesser	
																						cooling	effect.
Note:
	 The	fan	noise	becomes	louder	in	On 1 and  On .	
Fan control
Setting
This	function	is	used	to	set	a	frequency	for	the	filter	
cleaning.
When 	the 	projector 	reached 	a 	specified 	time 	between	
cleanings, 	a 	Filter 	warning 	icon 	appears 	on 	the 	screen,	
notifying	 the	cleaning	 is	necessary.	 After	cleaning	 the	filter,	
be 	sure 	to 	select 	
RESET 	and 	set 	the 	timer. 	The 	Filter	
warning	icon	will	not	turn	off	until	the	filter	counter	is	reset.
For	 details	 about	resetting	 the	timer,	 refer	to	“Resetting	 the	
Filter	Counter”	on	page	62.
Filter counter 
Filter counter
Press	the	SELECT 	button	to	select		Timer,	and	
then	use	the	Point	
◄►	buttons	to	set	the	timer.	
Select	from	(
Off/100H /	00H /	00H )	depending	
on	the	use	environment.
Filter	warning	icon	appears	on	the	screen	at	a	set	time. Fig .1 			Filter	warning	icon
Note:
	 This	icon	also	appears	at	turning	on.
Note:
				 The	Lamp	replacement	icon	will	not	appear	when	the	
				Display	function	is	set	to	
Off 	(p.46),	during	"FREEZE	
button"	(p.25),	or
  "NO	SHOW	button"	(p.26). 
						

							
5

Factory default
This	function	returns	all	setting	values	except	for	the	User 
logo,	PIN code lock ,	Logo PIN code lock ,	Lamp counter	
and	
Filter counter 	to	the	factory	default	settings.
Factory default
WARNING log
This	function 	records 	anomalous 	operations 	while 	the	
projector	 is	in	 operation	 and	use	it	when	 diagnosing	 faults.	
Up	 to	10	 warning	 logs	are	displayed	 with	the	latest	 warning	
message	 at	the	 top	of	the	 list,	 followed	 by	previous	 warning	
messages	in	chronological	order.	
Note:
	 		When 	the 	Factory 	default 	function 	is 	executed, 	all 	the	
warning	log	records	will	be	deleted.
Setting
Power management                                      Off                  On start                                                         Off
---- 
						

							
60

Input Source Information Display
The	Information	Menu	is	used	for	checking	the	status	of	the	image	signal	being	projected	and	the	operation	of	the	projector.
H-sync freq .
V-sync freq .
Lamp counter
Information Menu
The	horizontal	frequency	of	the	input	signal	is	displayed	in	
KHz,	or	- - - - -	when	no	signal.
The	vertical	frequency	of	the	input	signal	is	displayed	in	
Hz ,	
or	
- - - - - 		when	no	signal.	Numbers	of	Hz	doubles	when	
during	Interlace.
The	cumulative	lamp	operating	time	is	displayed.
Direct Operation
Press	the	INFO.	button	on	the	remote	control	to	display	the	
Information	Menu.
INFO . button
Remote Control
Press	the	Point	▲▼	buttons	to	select	the	Information.	 The	
Information	Menu	is	displayed.	
See	below	for	displayed	information.
Menu Operation
Power management
Screen
Off ,	Ready ,	Shut down 	or	Timer	is	displayed.
The	selected	screen	size	is	displayed.
Input
Lamp status The	selected	input	source	is	displayed.
The	selected	lamp	mode	is	displayed.
Information
Language
The	selected	language	is	displayed.
Key lock
The	selected	Key	lock	icon	is	displayed.
PIN code lock
Off 	or	On 1 	or	On  	is	displayed.
Remote control
The	selected	remote	code		is	displayed.