Eiki Projector Lc Wb100 User Manual
Have a look at the manual Eiki Projector Lc Wb100 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 422 Eiki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
41 Image Adjustment 1 Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63). Press the Point ◄ button to decrease the brightness; press the Point ► button to increase the brightness (from 0 to 63). Contrast Brightness Press the Point ◄ button to lighten red tone; press the Point ► button to deepen red tone (from 0 to 63). White balance (Red) Press the Point ◄ button to lighten green tone; press the Point ► button to deepen green tone (from 0 to 63). White balance (Green) Press the Point ◄ button to lighten blue tone; press the Point ► button to deepen blue tone (from 0 to 63). White balance (Blue) Use the Point ◄► buttons to select the desired Color temp. level (XLow, Low, Mid or High). Color temp . Press the Point ◄ button decrease the intensity of the color; press the Point ► button increase the intensity of the color (from 0 to 63). Press the Point ◄► buttons to adjust the tint value to get a proper color balance (from 0 to 63). Color Tint Note: • When the White balance Red , Green, or Blue is adjusted, the Color temp. level will change to User. • Tint cannot be selected when the video system is PAL , SECAM , PAL-M or PAL-N (p.39). • When Blackboard(Green) or Colorboard is selected in Image select, Color temp . will change to Blackboard or Colorboard. Image adjust MenuPress the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select the Image adjust and then press the Point ► or the SELECT button. Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value. Selected Image mode Use the Point ◄► buttons to adjust the setting value. Video Input
4 Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15). Gamma Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 15). Sharpness An interlaced video signal can be displayed in progressive mode. Select one of the following options. Off .......... Disabled. L1 .......... For an active picture. L2 .......... For a still picture. Film ........ For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Progressive Noise reduction Noise interference on the screen can be reduced. Select one of the following options to get smoother images. Off .......... Disabled. L1 .......... Lower reduction L2 .......... Higher reduction Note: Noise reduction and Progressive cannot be selected when 480p , 575p, 70p , 105i , 1080i or 1080p is selected (p.39). To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select y es . All adjustments will return to their previous figures. Reset Store To store the adjusted data, select Store and press the SELECT button. Use the Point ▲▼ buttons to select one from Image 1 to 4 and press the SELECT button. A confirmation box appears and then select yes . Stored data can be called up by selecting an Image (1- 4) in the Image Mode Selection on page 33. Store Menu A confirmation box appears and then select yes . Video Input
4 This projector has the picture screen resize function, which enables you to customize the image size. Screen Size Adjustment Screen Menu 0 0Off 0 0 Video Input Normal Provide the image to fit the screen size while maintaining the aspect ratio of input signal. Custom Adjust the screen scale and position manually with this function. Press the Point ► button at Custom and the Custom is displayed on the screen, you can use the Point ▲▼ buttons to choose the item you want to adjust. Scale H/V .......... Adjust the Horizontal/Vertical screen scale. H&V ................... When set to On, the aspect ratio is fixed. Scale V appears dimmed and becomes unavailable. Adjust the Scale H, then the screen scale is automatically modified based on the aspect ratio. Position H/V . . . . . Adjust the Horizontal/Vertical screen position. Common ........... Save the adjusted scale to all the inputs. Press the SELECT button at Common to display a confirmation box. To save the scale, press the SELECT button at yes , When Custom is selected, the saved scale is used. Reset ................. Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at yes . Note: • When no signal is detected, Normal is set automatically and the Aspect dialog box disappears. • The adjustable range for Scale H/V and Position H/V is limited depending on the input signal. • Wide , Zoom and Natural wide cannot be operated when 70p, 105i or 1080i is selected in the AV System Menu (p.39). Wide Provide the image at the 16:9 wide screen ratio. Only for 4:3 video aspect ratio signals. Full Provide the full screen image. Zoom Pan the horizontal direction of the image and cut the vertical direction of the image to fit the screen size (16:9). Only for 4:3 video aspect ratio signals. Natural wide Modify the 4:3 aspect ratio image to fit the screen size(16:9 aspect ratio) by stretching the image to make it look natural. 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Screen and then press the Point ► or the SELECT button. Use the Point ▲▼ buttons select the desired item and then press the SELECT button.
44 Language The language used in the On-Screen Menu is available in English, German , French, Italian, Spanish , Portuguese , Dutch, Swedish , Finnish, Polish, Hungarian , Romanian, Russian, Chinese, Korean, japanese and Thai. Setting Menu Setting Setting 1 This projector has a Setting menu that allows you to set up the other various functions described below. Language Menu position Picture in PictureStandby mode Network Picture in PictureStandby mode Network Press the MENU button to display the On-Screen Menu. Press the Point ▲▼ buttons to select Setting and press the Point ► or the SELECT button to access the submenu items. Use the Point ▲▼ buttons to select the desired item and then press the Point ► or the SELECT button to access the selected item. Use the Point ▲▼ buttons to select the desired item and then press the SELECT button. This function is used to change the position of the On-Screen Menu. Select Menu position and press the SELECT button. The Menu position screen appears. The Menu position changes each time you press the SELECT button as follows. the top left the top right the center the bottom left the bottom right the top left .....
45 Note: • Input search, Auto PC adj . and Auto Keystone cannot be set Off at the same time. • Auto Keystone corrects vertical distortion only, not correct horizontal distortion. • The Auto Keystone function cannot work when the Ceiling feature is set On in the Setting menu (p.50). • Perfect correction of the image distortion cannot be ensured with the Auto setup function. If the distortion is not corrected properly by pressing the AUTO SETUP or AUTO SET button, adjust manually by pressing the KEYSTONE button on the remote control or selecting Keystone in the Setting menu (pp.23, 46). • Fine sync . , Total dots, Horizontal and Vertical position of some computers cannot be fully adjusted with the Auto PC adjustment function. When the image is not provided properly with this operation, manual adjustments are required (pp.31-32). • Only the last selected input source can be detected. Auto setup Input search This function detects the input signal automatically. When a signal is found, the search will stop. Use the Point ▲▼ buttons to select one of the following options. Off ........... Input search will not work. On1.......... Input search works under the following situation. – When pressing the AUTO SETUP button on the top control. – When pressing the AUTO SET button on the remote control. On .......... Input search works under the following situation. – When turning on the projector by pressing the ON/STAND-BY button on the top control or the remote control. – When pressing the AUTO SET button on the remote control. – When pressing the AUTO SETUP button on the top control. – When the current input signal is cut off.* * If the No show or Freeze function is active, cancel it to activate the Input search. It is also unavailable when On- Screen menu is displayed. Auto PC adj . On. . . . . . . . Enables Auto PC adjustment when pressing the AUTO SET button on the remote control or the AUTO SETUP button on the top control. Off. . . . . . . .Disables Auto PC adjustment. Auto Keystone Auto . . . . . Always works and corrects keystone distortion according to the projector's tilt. Manual . . . .Works only when pressing the AUTO SETUP button on the top control or the AUTO SET button on the remote control. Off. . . . . . . . Disables Auto Keystone. Auto setup Note: • While Input search is set to On1 or On , the status of Input and Lamp are displayed every time the signal is switched. • During Input search is in progress, if the INPUT button on the top control, the COMPUTER1/2, HDMI, S- VIDEO, COMPONENT or the VIDEO button on the remote control, the MENU button or the ON/STAND-BY button is pressed, Input search will stop. If the INPUT button is pressed, the Input search will go back to the current search signal. If the COMPUTER 1/2, HDMI, VIDEO, S-VIDEO or COMPONENT button is pressed, Input search will go back to the button's input signal. This function enables Input search, Auto Keystone correction and Auto PC adjustment by pressing the AUTO SETUP button on the top control or the AUTO SET button on the remote control. Settings for those functions can be altered as follows: Picture in PicturePicture in PictureStandby mode Network Setting
46 Keystone This function is used to store or reset the keystone correction when the AC power cord is unplugged. Use the Point ▲▼ buttons to switch between each option. Store ....... Keep the keystone correction even when the AC power cord is unplugged. Reset ....... Release the keystone correction when the AC power cord is unplugged. To correct keystone distortion, press the SELECT button. Keystone appears on the screen. Use the Point ▲▼ buttons to correct keystone distortion (p.23). Background Select the background screen for when no input signal is detected. Press the Point ▲▼ buttons to switch between each option. Blue . . . Project a blue background Black . . Project a black background User. . . Project an image captured in the Logo setting. This function decides whether to display On-Screen Displays. On ............................ Show all the On-Screen displays. Use this function when you want to project images after the lamp becomes bright enough. The factory default setting is in this option. Countdown Off ......... Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off ............................ Hide the On-Screen Displays except; ● On-Screen Menu ● Power off? (p.20) ● No signal for Power management (p.52) ● Please wait ... ● Arrows for the True function in the Screen Menu (p.35) ● P-Timer Display Keystone Picture in PicturePicture in PictureStandby mode Network Setting
47 Logo (Logo and Logo PIN code lock settings) Logo selectThis function allows you to customize the screen logo with Logo select , Capture, Logo PIN code lock and Logo PIN code change functions. Note: When On is selected in the Logo PIN code lock function, Logo select and Capture functions cannot be selected. Logo select This function decides on the starting-up display from among following options. User ........ Show the image you captured. Default .... Show the factory-set logo. Off ........... Show the countdown display only. Picture in PictureStandby mode Network Setting
48 Capture Capture This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations. Select Capture and press the SELECT button. A confirmation box appears and select yes to capture the projected image. After capturing the projected image, go to the Logo select function and set it to User . Then the captured image will be displayed the next time you turn on the projector. To cancel the capture function, select yes in the "Quit?" confirmation box. Note: • Before capturing an image, select Standard in the Image select Menu to capture a proper image (pp.33, 40). • A signal from a computer can be captured up to WXGA (1280 x 800). A signal from video equipment can be captured except for 1035i, and 1080i. • When capturing the image that has been adjusted by the Keystone function, the adjusted data is automatically reset and the projector captures an image without keystone correction. • When Logo PIN code lock is set to On, capture cannot be selected. • When starting to capture a new image, the previously stored image is cleared even if you cancel the capturing. • When there is no captured image or it is interrupted while capturing an image, User is not included in Logo Select menu, you can only switch between Default and Off. Logo PIN code lockThis function prevents an unauthorized person from changing the screen logo. Off ........... The screen logo can be changed freely from the Logo Menu (p.47). On ........... The screen logo cannot be changed without a Logo PIN code. If you want to change the Logo PIN code lock setting, press the SELECT button and the Logo PIN code dialog box appears. Enter a Logo PIN code by following the steps below. The initial Logo PIN code is set to “4321” at the factory. Logo PIN code lock Setting
4 Enter a Logo PIN code Use the Point ▲▼ buttons to enter a number. Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to “ ”. If you fixed an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number. Repeat this step to complete entering a four-digit number. After entering the four-digit number, move the pointer to Set . Press the SELECT button so that you can start to operate the projector. If you entered an incorrect Logo PIN code, Logo PIN code and the number ( ) will turn red for a moment. Enter the correct Logo PIN code all over again. Logo PIN code can be changed to your desired four-digit number. Press the SELECT button to select Logo PIN code change. Logo PIN code dialog box appears, use the Point ▲▼ buttons to enter the correct code. The New Logo PIN code input dialog box appears. Set a new Logo PIN code, confirmation box appears, choose yes to set the new Logo PIN code. Be sure to note the new Logo PIN code and keep it on hand. If you lost the number, you could no longer change the Logo PIN code setting. Use the Point ▲▼ buttons to switch On or Off , and then press the SELECT button to make a choice. Change the Logo PIN code lock setting Enter a Logo PIN code CAUTION: WHEN yOU HAVE CHANGED THE LOGO PIN CODE, WRITE DOWN THE NEW PIN CODE IN COLUMN OF THE LOGO PIN CODE NO . MEMO ON PAGE 80, AND KEEP IT SECUREL y . SHOULD THE LOGO PIN CODE BE LOST OR FORGOTTEN, THE LOGO PIN CODE SETTING CAN NO LONGER BE CHANGED . Logo PIN code change Setting Cancel Cancel Logo PIN code change
50 Ceiling Rear Ceiling When this function is set to On, the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to On , the picture will be left/right reversed. This function is used to project the image from rear of the screen. Setting HDMI setup Picture in PictureStandby mode Network HDMI setup This function is only used for HDMI input source. Image Normal : When the output of Digital R/G/B equipment is set to Standard . Enhanced : When the output of Digital R/G/B equipment is set to Enhanced. Sound HDMI : When Digital input source is input, Sound is set to HDMI. Computer : When DVI input source is changed to HDMI input source, Sound is set to Computer . The names for the output setting of Digital R/G/B vary from equipment to equipment. For details, refer to the owner’s manual of your Digital R/G/B equipment. When the black parts of the image are destroyed or stand out, please switch to Normal or Enhanced , and then switch the output type of the HDMI Digital R/G/B output equipment. Terminal The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for Computer 2 input or monitor output. (See page 9) Computer . . . Computer input Monitor out . . . Monitor out Terminal function is not available when selecting Computer to the input source. Change the input source to the others (HDMI or Computer 1 or Video) so that the Terminal function will be available. (pp.27-28, 37-38)